Instruction/ maintenance manual of the product 59022-11 A 4-13 Q-Logic
Go to page of 322
Simplify 0 59022-1 1 A Page i SANbox2-8c/16 Switch Management User ’ s Guide Firmware V ersion 5.0.
Page ii 59022-1 1 A 0 SANbox2-8c/16 Switch Manage ment User’s Guide © 2000–2005 QLogic Corporation First Printed: May 2001 All Rights Reserved Worldwide. Printed in U. S.A. Information fu rnished in this manual is believed to be accurate and reliab le.
59022-1 1 A Page iii T able of Content s Section 1 Introduction 1.1 Intended Audience .................................................... ......................................... 1-1 1.2 Related Materials ............................................
Page iv 59022-1 1 A SANbox2-8c/16 Switch Manage ment User’s Guide 0 2.1 1 SANsurfer Switch Manager User Interfa ce .................................... .................. 2-19 2.1 1.1 Menu Bar ..................................... ..................
59022-1 1 A Page v SANbox2-8c/16 Switch Management User’s Guide 0 3.2 Securing a Fabric ................................. .......................................... .................... 3-7 3.2.1 Connection Security .................................
Page vi 59022-1 1 A SANbox2-8c/16 Switch Manage ment User’s Guide 0 3.5 Displaying Fabric Information .................................................................... ....... 3-26 3.5.1 Fabric S tatus.......................................... ..
59022-1 1 A Page vii SANbox2-8c/16 Switch Management User’s Guide 0 3.7 Zoning a Fabric .................................................................... ............................ 3-37 3.7.1 Zoning Concept s ......................... .........
Page viii 59022-1 1 A SANbox2-8c/16 Switch Manage ment User’s Guide 0 Section 4 Managing Switches 4.1 Managing User Account s ..................................................... .............................. 4-2 4.1.1 Creating User Account s ....
59022-1 1 A Page ix SANbox2-8c/16 Switch Management User’s Guide 0 4.9 Restoring a Switch .................................................................................... ....... 4-36 4.10 Restoring the Factory Default Configuration ............
Page x 59022-1 1 A SANbox2-8c/16 Switch Manage ment User’s Guide 0 Appendix A Command Line Interface A.1 Logging On to a Switch ...................................................................................... A-1 A.2 User Account s ...........
59022-1 1 A Page xi SANbox2-8c/16 Switch Management User’s Guide 0 Show Setup Command................................................ .......................... A-1 1 1 Shutdown Command ............................. .................................
Page xii 59022-1 1 A SANbox2-8c/16 Switch Manage ment User’s Guide 0 Figures Figure Page 2-1 Initial Startup Dialog ......................................... ..................................................... ....... 2 -10 2-2 SANsurfer Switch Manager Window .
59022-1 1 A Page xiii SANbox2-8c/16 Switch Management User’s Guide 0 5-1 Faceplate Display - Port Information .......................................................... .................... 5-1 5-2 Port Properties Dialog ............................
Page xiv 59022-1 1 A SANbox2-8c/16 Switch Manage ment User’s Guide 0 A-10 Port Configuration Defaults ................................................................................... ....... A-47 A-11 Port Threshold Alarm Configuration Defaults..
59022-1 1 A 1-1 Section 1 Introduction This manual describes the switch managem ent too ls which include the SANsurf er Switch Manager™ application (version 5.00) and the Command Line Interface (CLI) for the SANbox2 Fibre Channel switch (firmware version 5.
1 – Introduction JDOM License 1-2 59022-1 1 A 0 1.3 JDOM Licen se This product includes soft ware dev eloped by the JDOM Project (http://www .jdom.org/).
1 – Introduction Technical Support 59022-1 1 A 1-3 0 1.4 T echnical Suppor t Customers should cont act their authorized maintenance provider for technical support of their QLogic switch product s. QLogic-direct customers may contact QLogic T echnical Support; others will be redire cted to their authorized maintenance provider .
1 – Introduction Technical Support 1-4 59022-1 1 A 0 Notes.
59022-1 1 A 2-1 Section 2 Using SANsurfer Switch Manager This section describes how to use the SA Nsu rfer Switch Manager application and its menus. The following topics are covered: Workst ation .
2 – Using SANsurfer Switch Ma nager Workstation Requirem ents 2-2 59022-1 1 A 0 2.1 Wo rkst ation Requirements The requirements for fa bric management wo rkstatio ns running SANsurfer Switch Manager.
2 – Using SANsurfer Switch Manager Installing the Manageme nt Application 59022-1 1 A 2-3 0 2.2.1 SANsurfer Switch Manager Y ou can inst all SANsurfer Switch Manag er on a Windo ws, Linux, Solaris, or Mac OS X workstation.
2 – Using SANsurfer Switch Ma nager Installing the Manage ment Application 2-4 59022-1 1 A 0 For a Mac OS X plat form: 1. Open the CD and move to the following fo lder: data/files/Management_Software/MacOSX 2. Double click the applicat on zip file (MacOSX_5.
2 – Using SANsurfer Switch Manager Installing the Manageme nt Application 59022-1 1 A 2-5 0 6. Y ou can run the inst allation file from the CD-ROM or download the installation file to your hard drive. Choose one of the following : Open the installa tion file from the CD-ROM and follow the SANsurfer Switch Manager installation in structions.
2 – Using SANsurfer Switch Ma nager Installing the Manage ment Application 2-6 59022-1 1 A 0 2.2.2.2 SMS Inst allation for Linux Close all programs currently running, and insert the SANsurfer Management Suite Installation Disk into the manage ment wo rkstation CD-ROM drive.
2 – Using SANsurfer Switch Manager Installing the Manageme nt Application 59022-1 1 A 2-7 0 10. T o ensure that you are using the most recent version of SANsurfer Switch Manager, visit the QLogic support web p age and go to Drivers, Sof tware and Manuals .
2 – Using SANsurfer Switch Ma nager Installing the Manage ment Application 2-8 59022-1 1 A 0 3. On the SANbox Switch Softwa re page, scroll to the SANbox2-8c/ 16 Series area. 4. In the Operating System column, click the Solaris SP ARC link. 5. Click the SANsurfer Management Sof tware link to open the Save As dialog.
2 – Using SANsurfer Switch Manager Starting SANsurfer Switch Manager 59022-1 1 A 2-9 0 15. When prompted for the SMS inst allation directory , enter d if SMS was installed in it’s d efault directory (/opt/QLogic_Corporation/SANsurfe r). Otherwise, enter the p ath name for the SMS inst allation directory .
2 – Using SANsurfer Switch Ma nager Starting SANsurfer Switch Manager 2-10 59022-1 1 A 0 T o start SANsurfer Switch Man ager from SANsurfer Management Suite, do the following.
2 – Using SANsurfer Switch Manager Starting SANsurfer Switch Manager 59022-1 1 A 2-1 1 0 Click the Open Existing Fabric View File radio button to open the Open View dialog which p rompts you to specif y a f abric view file that you saved earlier .
2 – Using SANsurfer Switch Ma nager Exiting SANsurfer Management Suite 2-12 59022-1 1 A 0 2.4 Exiting SANsurfer Mana gement Suite T o exit a SANsurfer Switch Manager application session, open the File menu and select Exit .
2 – Using SANsurfer Switch Manager Uninstalling SANsur fer Switch Manager 59022-1 1 A 2-13 0 In your next SANsurfer Switch Manager session , the Load Default Fabric File dialog shown in Figure 2-4 prompt s you to load the default fabric view file and to specify its encryption key , if there is one.
2 – Using SANsurfer Switch Ma nager Uninstalling SANsurfer Switch Man ager 2-14 59022-1 1 A 0 2.5.1 SMS Uninst all A program to uninst all SANsurfer Management Suite was included a s part of the SANsurfer Management Suite inst allation process.
2 – Using SANsurfer Switch Manager Changing the Encryption Key for th e Default Fabric View File 59022-1 1 A 2-15 0 2.5.2 S t andalone Uninstall A program to uninst all SANsurfer Switch Manager was included as p art of the installation process. Use t his method only if you inst alled SANsurfer Switch Manager as a st andalone program.
2 – Using SANsurfer Switch Ma nager Saving and Opening Fa bric View Files 2-16 59022-1 1 A 0 2.7 Saving and Opening Fabric View Files A fabric view file is one or more fabrics saved to a file. In addition to the SANsurfer Switch Manager default fabric view file, you can save and op en your own fabric view files.
2 – Using SANsurfer Switch Manager Setting SANsurfer Switch Manager Prefere nces 59022-1 1 A 2-17 0 Enable (default) or disable the Event Browser .
2 – Using SANsurfer Switch Ma nager Using Online Help 2-18 59022-1 1 A 0 2.9 Using Online Help Online help is available for the SANsurf er Switch Manager a pplication and its functions. The two ways to open the online h elp file are: open the He lp menu and select Help Topics , or click the Help button in th e tool bar .
2 – Using SANsurfer Switch Manager SANsurfer Switch Manager User Interface 59022-1 1 A 2-19 0 2.1 1 SANsurfer Switch Ma nager User Interface The SANsurfer Switch Manager application uses two basic displays to man age the fabric and individual sw itches: the topology display and the faceplate display .
2 – Using SANsurfer Switch Ma nager SANsurfer Switch Manager User Interfac e 2-20 59022-1 1 A 0 2.1 1.1 Menu Bar The SANsurfer Switch Manager menus and the t asks offered in them vary depending on the display . For example, t he Port menu and many of the Switch menu selections are only available in the face plate display .
2 – Using SANsurfer Switch Manager SANsurfer Switch Manager User Interface 59022-1 1 A 2-21 0 2.1 1.1.2 Faceplate Display Menu The menu options in the faceplate displa y are shown in Figure 2-8 . Figure 2-8. Faceplate Display Menu The keyboard shortcut keys vary by di splay type: to pology display and faceplate display .
2 – Using SANsurfer Switch Ma nager SANsurfer Switch Manager User Interfac e 2-22 59022-1 1 A 0 2.1 1.2 To o l B a r The tool bar consists o f a row of graphical buttons that you can use to access SANsurfer Switch Manager functio ns as shown in T able 2-2 .
2 – Using SANsurfer Switch Manager SANsurfer Switch Manager User Interface 59022-1 1 A 2-23 0 2.1 1.3 Fabric T ree The fabric tree list s the managed fabr ics an d their switches as shown in Figure 2-9 . The window width can be adjusted by clicking and dragging the moveable window border .
2 – Using SANsurfer Switch Ma nager SANsurfer Switch Manager User Interfac e 2-24 59022-1 1 A 0 2.1 1.4 Graphic Window The graphic window , as shown in Figure 2-6 , presents graphic information about fabrics and switches such as the fabric topology and th e switch faceplate.
2 – Using SANsurfer Switch Manager Using the Topology Display 59022-1 1 A 2-25 0 2.12 Using the T opology Display The topology display shown in F igure 2-10 receives information from the selected fabric and displays it s topology . Switches and inter-switch links (ISLs) appear in the graphic window and use color to indicate st atus.
2 – Using SANsurfer Switch Ma nager Using the Topology Display 2-26 59022-1 1 A 0 2.12.2 Wo rking with Switches and Links Switch and link icons are selectable a nd moveable, and serve as access point s for other displays and menus.
2 – Using SANsurfer Switch Manager Using the Topology Display 59022-1 1 A 2-27 0 2.12.3 Opening the Faceplate Display and T opology Popu p Menus The faceplate display shows the front of a sing le switch and it s ports.
2 – Using SANsurfer Switch Ma nager Using the Faceplate Display 2-28 59022-1 1 A 0 2.13 Using the Faceplate Display The faceplate display shown in Figure 2-1 1 displays the switch name and operational sta te, and port st atus.
2 – Using SANsurfer Switch Manager Using the Faceplate Displ ay 59022-1 1 A 2-29 0 2.13.2 Wor k i n g w i t h P o r ts Ports are se lectable and serve as access point s for other displays and menus. Y ou select port s to display information about them in the data window or to modify them.
2 – Using SANsurfer Switch Ma nager Using the Faceplate Display 2-30 59022-1 1 A 0 2.13.2.2 Opening the F aceplate Popup Menu T o open the popup menu, right-click the fac eplate image to present t he following task s.
2 – Using SANsurfer Switch Manager Using the Faceplate Displ ay 59022-1 1 A 2-31 0 2.13.3 Faceplate Dat a Windows The faceplate display provides the following data windo ws corresponding to the data window t abs: Devices – displays informa tion about devices (hosts and storage target s) connected to the switch.
2 – Using SANsurfer Switch Ma nager Using the Faceplate Display 2-32 59022-1 1 A 0 Notes.
59022-1 1 A 3-1 Section 3 Managing Fabrics This section describes the follo wing tasks that manage fabrics: RADIUS Servers Securing a Fabric T racking Fabric Firmware and Software V ersions Managing the Fabric Database Displaying Fabric Information Working with Device Information and Nicknames Zoning a Fabric 3.
3 – Managing Fa brics RADIUS Servers 3-2 59022-1 1 A 0 3.1.1 Adding a RADIUS Server When you add a RADIUS server , you provide a method to centralize the management of authentication p asswords over a network. Figure 3-1. Add Server T o add a RADIUS server , do the following: 1.
3 – Managing Fabrics RADIUS Servers 59022-1 1 A 3-3 0 7. In the Retries field, enter the the numb er of retries. This is the maximum number of times the RADIUS client will retry a req uest sent to the primary RADIUS server .
3 – Managing Fa brics RADIUS Servers 3-4 59022-1 1 A 0 3.1.2 Removing a RADIUS Server When you remove a RADIUS server , you disable the management of authentication usernames and passwords ove r the network for that server . Figure 3-2. Remove Server T o remove a RADIUS server , do the following: 1.
3 – Managing Fabrics RADIUS Servers 59022-1 1 A 3-5 0 3.1.3 Editing RADIUS Server Information Editing information of a RADIUS server involves changin g the configuration of a RADIUS server . Figure 3-3. Edit Ra dius Server Information T o edit information of a RADIUS server , do the following: 1.
3 – Managing Fa brics RADIUS Servers 3-6 59022-1 1 A 0 3.1.4 Modifying Authentication Orde r RADIUS Server Information Editing information of a RADIUS server involves changin g the configuration of a RADIUS server .
3 – Managing Fabrics Securing a Fa bric 59022-1 1 A 3-7 0 3.2 Securing a Fabric Fabric security consist s of the following: Connection Security User Account Security Security Consistency Checklist Device Security Fabric Services 3.
3 – Managing Fa brics Securing a Fabric 3-8 59022-1 1 A 0 3.2.2 User Account Security User account security is the process by which yo ur user account and password are authenticated with the list of valid use r accounts and p asswords.
3 – Managing Fabrics Securing a Fa bric 59022-1 1 A 3-9 0 3.2.4 Device Security Device security provides for the authorization and a uthentication of devices tha t you attach to a switch.
3 – Managing Fa brics Securing a Fabric 3-10 59022-1 1 A 0 3.2.4.1 Edit Security Dialog The Edit Security dialog, shown in Figure 3-5 open s after clicking the Secur ity button on the toolbar or select ing Edit Security from the Security menu.
3 – Managing Fabrics Securing a Fa bric 59022-1 1 A 3-1 1 0 Use the File menu to: Edit the security configuration on the switch. Open or edit security files.
3 – Managing Fa brics Securing a Fabric 3-12 59022-1 1 A 0 3.2.4.3 Create Security Group Dialog Use the Create Security Group dialog, shown in Figure 3-6 , to add a security group to a security set.
3 – Managing Fabrics Securing a Fa bric 59022-1 1 A 3-13 0 3.2.4.4 Creating a Security Group An empty (no members) security group in the active security set will prevent all connections for that security group type. F or example, an empty ISL security group will cause the switch to refuse all lo gins from other switches.
3 – Managing Fa brics Securing a Fabric 3-14 59022-1 1 A 0 3.2.4.5 Create Security Group Member Dialog Use the Create Security Group Member dialog, shown in Figure 3-7 , to add a member to a security group.
3 – Managing Fabrics Securing a Fa bric 59022-1 1 A 3-15 0 The conventions for MS security group members are list ed below: Y ou can enter membe r world-wide name (WWN), which must be 16 hex characters, or 23 characters with vali d WWN format xx:xx:xx:xx:xx:xx:xx:xx.
3 – Managing Fa brics Securing a Fabric 3-16 59022-1 1 A 0 3.2.4.7 Editing the Security Co nfiguration on a Switch T o edit a security configuration on the switch, do the following: 1. On the faceplate display , click the Security button on the toolbar , or open the Security menu and select Edit Security to open the Edit Security dialog.
3 – Managing Fabrics Securing a Fa bric 59022-1 1 A 3-17 0 3.2.4.8 V iewing Properties of a Secu rity Set, Group, or Member T o view the properties of a security set, group, or member , do the following: 1.
3 – Managing Fa brics Securing a Fabric 3-18 59022-1 1 A 0 4. Click the Apply button to save the se ttings. 5. Click the OK button to close the Security Config dialog. 3.2.4.10 Archiving a Security Co nfiguration to a File T o archive (save) a security configuration to a file, do the following: 1.
3 – Managing Fabrics Securing a Fa bric 59022-1 1 A 3-19 0 3.2.4.13 Configured Security Dat a Window The Configured Security dat a window displays a graph ical represent ation of all security sets, group s, and members in the dat abase.
3 – Managing Fa brics Tracking Fabric Firmware and Softwar e Versions 3-20 59022-1 1 A 0 3.2.5.2 Enabling In-band Management T o enable In-band Management, do the followin g: 1. On the faceplate display , open the Switch menu and select Switch Properties to open the Switch Properties dialog.
3 – Managing Fabrics Tracking Fabric Firmware and So ftware Versions 59022-1 1 A 3-21 0 3.3.2 V iewing and Comp aring V ersion Snap shots The Differen ces tab p age shows a side-by-side comp arison of two snapshot s. The timestamp of each sna pshot is displa yed above the scroll area showing that snapshot.
3 – Managing Fa brics Managing the Fabric Database 3-22 59022-1 1 A 0 3.4 Managing the Fabric Dat abase A fabric dat abase contains the set of fabrics that you have added during a SANsurfer Switch Manager session.
3 – Managing Fabrics Managing the Fabric Database 59022-1 1 A 3-23 0 4. Click the Add Fabric button. 3.4.2 Removing a Fabric T o delete a fabric from the database , do the following: 1. Select a fabric in the fabric tree. 2. Open the Fabric menu and select Remove Fabric .
3 – Managing Fa brics Managing the Fabric Database 3-24 59022-1 1 A 0 3.4.4 Saving a Fabric V iew File T o save a fabric view file, do the following: 1. Open the File menu, and select Save View As . 2. In the Save V iew dialog, enter a new file n ame.
3 – Managing Fabrics Managing the Fabric Database 59022-1 1 A 3-25 0 5. Configure the port types for the new sw itch using th e Port Properties dialog. The ports can be G_Port, GL_Port, F_Port, FL_Port, or Donor . 6. Connect the devices to the switch.
3 – Managing Fa brics Displaying Fabric Information 3-26 59022-1 1 A 0 4. Restore the configuration from th e failed switch to the replacement switch: a. Open a new fabric through the replacement switch. b. Open the faceplate display for the rep lacement switch.
3 – Managing Fabrics Displaying Fabric Information 59022-1 1 A 3-27 0 3.5.1 Fabric S t atus The fabric updates the topology an d faceplate displays by fo rwarding changes in status to the manage ment workstation a s they occur . Y ou can allow the fabric to update the display st atus, or you can refresh the display at any time.
3 – Managing Fa brics Displaying Fabric Information 3-28 59022-1 1 A 0 3.5.2 Displaying the Event Browser The Event Browser displays a list of events generated by the switches in the fabric and the SANsurfer Switch Man ager application.
3 – Managing Fabrics Displaying Fabric Information 59022-1 1 A 3-29 0 Severity is indicated in the severity column usin g icons as described in T able 3-2 . T able 3-2. Severity Levels Severity Icon Description Alarm – An Alar m is a "serviceable ev ent".
3 – Managing Fa brics Displaying Fabric Information 3-30 59022-1 1 A 0 3.5.2.1 Filtering the Event Browser Filtering the Event Browser enables you to display only those events that are of interest based on the event severity , timestamp, source, type, and description.
3 – Managing Fabrics Displaying Fabric Information 59022-1 1 A 3-31 0 3.5.2.2 Sorting the Event Browser Sorting the Event Browser enables yo u to display the event s in alphanumeric order based on the event se verity , timestamp, source, type, or description.
3 – Managing Fa brics Displaying Fabric Information 3-32 59022-1 1 A 0 3.5.3 Devices Dat a Window The Devices data wind ow displays information about the devices that are logged into the fabric. Click the Devices t ab below the data window to displa y device information for all devices that are logged into the selected fabric.
3 – Managing Fabrics Displaying Fabric Information 59022-1 1 A 3-33 0 3.5.4 Active Zone Set Dat a Window The Active Zoneset dat a window displays the zone membership for the active zone set that resides on the fabric management switch.
3 – Managing Fa brics Working with Device Information and Nicknames 3-34 59022-1 1 A 0 3.5.5 Link Dat a Window The Link data win dow displays information about all switch links in the fabric or selected links. This information includes the swit ch name, the port number at t he end of each link, and the link st atus ic on.
3 – Managing Fabrics Working with Device Information and Nickna mes 59022-1 1 A 3-35 0 3.6.2 Exporting Device Information to a File T o save device information to a file, o pen the topology display and do the following: 1. Select one or more switches.
3 – Managing Fa brics Working with Device Information and Nicknames 3-36 59022-1 1 A 0 3.6.3.2 Editing a Nickname A nickname must start with a letter an d can have up to 64 characters. V alid characters include alphanumeric characters [aA-zZ][0-9] and special symbols [$ _ - ^ ].
3 – Managing Fabrics Zoning a Fabric 59022-1 1 A 3-37 0 3.6.3.5 Importing a Nicknames File Importing a nicknames file c opies its content s into and replaces the contents of the Nicknames.xml file whic h is used by SANsurfer Switch Manager. T o import a nickname file, do the following: 1.
3 – Managing Fa brics Zoning a Fabric 3-38 59022-1 1 A 0 3.7.1.1 Zones A zone is a named group of port s or devices that can communicate with each other . Devices within a zone can only communicate with other devices in the same zone. A device may particip ate in more than one zone.
3 – Managing Fabrics Zoning a Fabric 59022-1 1 A 3-39 0 3.7.1.1.2 Access Control List Hard Zones Access Control List (ACL) zoning divides the fabric for p urposes of controlling discovery and inbound traf fic. ACL zoning is a type of hard zoning that is hardware enforced.
3 – Managing Fa brics Zoning a Fabric 3-40 59022-1 1 A 0 3.7.1.4 Zoning Dat abase Each switch has its own zoning dat abase. The zoning database is made up of all aliases, zones, and zone set s that have been created on the switch or received from other switches.
3 – Managing Fabrics Zoning a Fabric 59022-1 1 A 3-41 0 3.7.2 Using the Zoning W izard The Zoning Wizard is a series of dialogs that leads yo u through the process of zoning a fabric. T o open the Zoning Wizard, open th e Wizards menu in the faceplate display , and select Zoning Wizar d .
3 – Managing Fa brics Zoning a Fabric 3-42 59022-1 1 A 0 3.7.3.1 Editing the Zoning Dat abase T o edit the zoning database for a p artic ular switch, open the Zoning menu from the faceplate display and select Edit Zoning to open the Edit Zoning dialog shown in Figure 3-15 .
3 – Managing Fabrics Zoning a Fabric 59022-1 1 A 3-43 0 The Edit Zoning dialog has a Z one Sets tr ee on the left a nd a Port/Device (or members) tree on the right. Both tre es use display conventions similar to the fabric tree for exp anding and contracting zone sets, zones, and port s.
3 – Managing Fa brics Zoning a Fabric 3-44 59022-1 1 A 0 3.7.3.2 Configuring the Zoning Dat abase Use the Zoning Config d ialog to change the Auto Save, Default V isibility , and Discard Inactive configuration parameters.
3 – Managing Fabrics Zoning a Fabric 59022-1 1 A 3-45 0 3.7.3.2.1 Interop Auto Save The Interop Auto Save parameter determines whether cha nges to the active zone set that a switch receives from other switches in the fabric will be saved to the zoning datab ase on that swit ch.
3 – Managing Fa brics Zoning a Fabric 3-46 59022-1 1 A 0 3.7.3.4 Restoring the Zoning Dat abase from a File Do the following to restore the zoning d atabase from a file to a switch: 1. In the faceplate display , open the Zoning menu and select Edit Zoning to open the Edit Zoning window .
3 – Managing Fabrics Zoning a Fabric 59022-1 1 A 3-47 0 3.7.4 Managing Zone Set s Zoning a fabric involves creating a zo ne set, creating zones as zone set members, then adding devices as zone members.
3 – Managing Fa brics Zoning a Fabric 3-48 59022-1 1 A 0 4. T o create new zones in a zone set, do one of th e following: Right-click a zone set an d select Create A Zone from the popup menu. In the Create a Zone dialog, enter a n ame for the new zone, and click the OK button.
3 – Managing Fabrics Zoning a Fabric 59022-1 1 A 3-49 0 3.7.4.4 Removing a Zone from a Zone Set or from All Zone Set s Y ou can remove a zone from a zone set or from a ll zone sets in the database. 1. In the faceplate display , open the Zoning menu and select Edit Zoning to open the Edit Zoning d ialog.
3 – Managing Fa brics Zoning a Fabric 3-50 59022-1 1 A 0 3.7.5 Managing Zones Managing zones involves the following: Creating a Zone in a Zone Set Adding Zone Members Renaming a Zone or a Zone Set Removing a Zone Member Removing a Zone from a Zone Set Removing a Zone from All Zone Sets Changing Zone T ypes 3.
3 – Managing Fabrics Zoning a Fabric 59022-1 1 A 3-51 0 5. T o add switch ports or att ached devices to the zone, do one of the following: In the zone set tree, select the zone set. In t he graphic window , select the port to add to the zone. Open the Edit men u and select Add Members .
3 – Managing Fa brics Zoning a Fabric 3-52 59022-1 1 A 0 3. Click the OK button to add the member and save the change. 3.7.5.3 Renaming a Zone or a Zone Set T o rename a zone, do the following: 1. In the Zone Set s tree of the Edit Zoning dialog, click the zone/ zone set to be renamed.
3 – Managing Fabrics Zoning a Fabric 59022-1 1 A 3-53 0 3.7.5.6 Removing a Zone from All Zone Set s Zones that are no longer members of any zon e set are moved to the orphan zo ne set. The orphan zone set is saved on the switch. T o remove a zone from all zone sets inclu ding the orphan zone set, do the following: 1.
3 – Managing Fa brics Zoning a Fabric 3-54 59022-1 1 A 0 3.7.6.1 Creating an Alias T o create an alias, do the following: 1. Open the Zoning menu, and select Edit Zoning to op en the Edit Zoning dialog. 2. Open the Edit menu, and select Create Alia s to open the Create Alias dialog.
3 – Managing Fabrics Zoning a Fabric 59022-1 1 A 3-55 0 If the port/device you wan t to add is not in the Port/Device tree, you can add it by doing the following: a. Right click the selected alias. b. Open the Edit menu and select Create Members . c.
3 – Managing Fa brics Zoning a Fabric 3-56 59022-1 1 A 0 3.7.7.2 Zone Merge Failure Recovery When a zone merge failure occurs, the conf lict that caused the failure must be resolved.
59022-1 1 A 4-1 Section 4 Managing Switches This section describes the follo wing tasks that manage switches in the fabric. Managing User Account s Displaying Switch Information Configurin.
4 – Managing Switches Managing User Accounts 4-2 59022-1 1 A 0 4.1 Managing User Account s Only the Admin account can manage us er account s with the User Account Administration dialogs.
4 – Managing Switches Managing Us er Accounts 59022-1 1 A 4-3 0 4.1.1 Creating User Account s T o create a user account on a switch, o pen the Switch menu in the facepla te display and select User Accounts... . This displays the User Account Administration dialog shown in Figure 4-1 .
4 – Managing Switches Managing User Accounts 4-4 59022-1 1 A 0 4.1.2 Removing a User Account T o remove a user account on a switch, open the Switch menu in the fa ceplate display and select User Accounts... . Click the Remove Account t ab in the dialog to present the display sho wn in Figure 4-2 .
4 – Managing Switches Managing Us er Accounts 59022-1 1 A 4-5 0 4.1.3 Changing a User Accoun t Password T o change the password for an account on a switch, open the Switch menu in the faceplate display and select User Accounts... . Click the Change Password t ab in the dialog to present the display shown in Figure 4-3 .
4 – Managing Switches Managing User Accounts 4-6 59022-1 1 A 0 4.1.4 Modifying a User Account T o modify a user account on a switch, open the Switch menu in the faceplate display and select User Accounts... . This displays the User Account Administration dialog shown in Figure 4-4 .
4 – Managing Switches Displaying Switch Information 59022-1 1 A 4-7 0 4.2 Displaying Switch Information The faceplate display and dat a windows provide the following switch information: Device a.
4 – Managing Switches Displaying Switch Information 4-8 59022-1 1 A 0 The fabric updates the topology an d faceplate displays by fo rwarding changes in status to the manage ment workstation a s they occur . Y ou can allow the fabric to update the switch st atus, or you can refresh the d isplay at any time.
4 – Managing Switches Displaying Switch Information 59022-1 1 A 4-9 0 Super User Super user privileges enabled/disa bled UserAuthentication Enabled Enforcement of account names and authority (alw ay.
4 – Managing Switches Displaying Switch Information 4-10 59022-1 1 A 0 Interop Mode Zoning merge st atus. When a zone set is activated on an FC-SW-2 compliant switch, only the active zone set is propagated to all switches in the fabric.
4 – Managing Switches Displaying Switch Information 59022-1 1 A 4-1 1 0 W arning T emperature Non-configurable temperatur e threshold (65° Celsius) above which a warning condition alarm is ge nerated. Failure T emperature Non-configurable temperature thr eshold (70° Celsius) above which a failure condition ala rm is generated.
4 – Managing Switches Displaying Switch Information 4-12 59022-1 1 A 0 4.2.3 Port St atistics Dat a Window The Port S tatistics dat a window displays port performance dat a for the selected ports. T o open the Port S tatistics data window , click the Port Stats tab below the data window in the fa ceplate display .
4 – Managing Switches Displaying Switch Information 59022-1 1 A 4-13 0 4.2.4 Port Information Dat a Window The Port Information dat a window displays port detail information for the se lected ports. T o open the Port S tatistics data window , click the Port Info tab below the data window in the fa ceplate display .
4 – Managing Switches Displaying Switch Information 4-14 59022-1 1 A 0 4.2.5 Configured and Active Zoneset s Data W indow The Configured Zoneset s data window displa ys all zone sets , zones, aliases, and zone membership in the zoning dat abase, as shown in Figure 4-7 .
4 – Managing Switches Configuring Port Thresh old Alarms 59022-1 1 A 4-15 0 4.3 Configuring Port Threshold Alarms Y ou can configure the switch to genera te alarms for selected event s. Configuring an alarm involves choosing an event type, rising and falling triggers, a sample window , and finally enabling or disabling the alarm.
4 – Managing Switches Paging a Switch 4-16 59022-1 1 A 0 5. Enter a value for the rising trig ger . A rising trigger alarm is generated when the event count per interval exceeds the rising trigger .
4 – Managing Switches Setting the Date/Time and Enabling NTP Client 59022-1 1 A 4-17 0 4.5 Setting the Date/T ime and Enabling NTP Client The Date/T ime and Network T ime Protocol (NTP) dialog enabl.
4 – Managing Switches Resetting a Switch 4-18 59022-1 1 A 0 Common administrative operations that ch ange the fabric include: Zoning modifications. Adding, moving or removing devices att ached to the switch fabric. This includes powering up or powering down attached d evices.
4 – Managing Switches Configuring a Switch 59022-1 1 A 4-19 0 4.7 Configuring a Switch Switch configuration is divided into three areas: chassis configuratio n, network configuration, and SNMP configura ti on. Chassis configurat ion specifies switch-wide Fibre Channel settings.
4 – Managing Switches Configuring a Switch 4-20 59022-1 1 A 0 4.7.2 Switch Properties T o open the Switch Properties dialog, either select a switch in the topolo gy display or open the faceplate display for the switch you be configur ing, and then open the Switch menu and select Switch Propertie s .
4 – Managing Switches Configuring a Switch 59022-1 1 A 4-21 0 4.7.2.1 Symbolic Name The symbolic name is a use r-defined name of up to 32 characters that identifies the switch. The symbolic name is used in the topology and faceplate displays, as well as many data windo ws to more easi ly identify switches.
4 – Managing Switches Configuring a Switch 4-22 59022-1 1 A 0 4.7.2.3 Domain ID and Domain ID Lock The domain ID is a unique Fib re Channel identifier for the switch. The Fibre Channel address consist s of the domain ID, port ID, and the Arbitra ted Loop Physical Address (ALP A).
4 – Managing Switches Configuring a Switch 59022-1 1 A 4-23 0 4.7.2.4 Fabric Device Manageme nt Interface Fabric Device Management Interface (FDM I) provides a means to gather and display device information from the fabr ic, and allows FDMI cap able devices to register cert ain information with the fabric, if FDMI is enabled.
4 – Managing Switches Configuring a Switch 4-24 59022-1 1 A 0 4.7.2.5 Broadcast Support Broadcast is supported on the switch which allows for TCP/IP support. Broadcast is implemented using the proposed standard sp ecified in Multi-Switch Broadcast for FC-SW-3, T1 1 Presenta tion Number T1 1/02-031v0 .
4 – Managing Switches Configuring a Switch 59022-1 1 A 4-25 0 4.7.3 Advanced Switch Properties The Advanced Switch Properties dialog enables you to set the timeout values, Interop Mode, and Legacy Address Fo rmat settings.
4 – Managing Switches Configuring a Switch 4-26 59022-1 1 A 0 4.7.3.2 Legacy Port Address Format Legacy Address Format should be enabled only to permit interoperation with certain older non-FC-SW -2 compliant switches. Enabling this setting under other circumstances will disable zoning th at is defined by domain ID and port number .
4 – Managing Switches Configuring a Switch 59022-1 1 A 4-27 0 4.7.4 System Services Dialog The System Services dialog provide s a central location for you to enable or disable any of the external us.
4 – Managing Switches Configuring a Switch 4-28 59022-1 1 A 0 SSL - Secure Sockets Laye r . Provides secure encrypted communications between the switch management application (GUI) and the switch. SSL must be enabled for configu ration of security and RADI US servers with the switch management application (GUI).
4 – Managing Switches Configuring a Switch 59022-1 1 A 4-29 0 4.7.6 Network Properties Use the Network Properties dialog shown in Figure 4-13 to change IP configuration p arameters and enable remote logging . After making cha nges, click the OK button to put the new values into ef fect.
4 – Managing Switches Configuring a Switch 4-30 59022-1 1 A 0 4.7.6.1 IP Configuration The IP configuration ident ifies the switch on the Ethernet network and determines which network discovery method to use. Ta b l e 4 - 6 describes the IP co nfiguration parameters.
4 – Managing Switches Configuring a Switch 59022-1 1 A 4-31 0 4.7.6.2 Remote Logging The Remote Logging (syslog) feature enables saving of the log information to a remote host that support s the syslog protocol. When enab led, the log entries are sent to the syslog host at the IP address tha t you specify in the Logging Ho st IP Address field.
4 – Managing Switches Configuring a Switch 4-32 59022-1 1 A 0 4.7.7 SNMP Properties Use the SNMP Properties dialog shown in Figure 4-14 to change SNMP configuration p arameters. After making changes, click the OK button to put the new values into effe ct.
4 – Managing Switches Configuring a Switch 59022-1 1 A 4-33 0 4.7.7.1 SNMP Configuration The SNMP configuration define s how authentication trap s are managed. Ta b l e 4 - 7 describes the SNMP confi guration parameters. The illegal characters for the user-defined fields are the pound sign (#), semi-colon (;), and comma (,).
4 – Managing Switches Configuring a Switch 4-34 59022-1 1 A 0 4.7.7.2 SNMP T rap Configuration The SNMP trap configuration defines how trap s are set. Choose from the t abs Trap1 – Trap 5 to configure each trap. T able 4-8 descri bes the SN MP configuration p arameters.
4 – Managing Switches Archiving a Switch 59022-1 1 A 4-35 0 4.8 Archiving a Switch Y ou can create an .XML arch ive file c ontaining the configuration p a rameters. Basically any data received by SANsurfer Switch Manager is archived. However , passwords are not arch ived with the user account information.
4 – Managing Switches Restoring a Switch 4-36 59022-1 1 A 0 4.9 Restoring a Switch Restoring a switch loads the archived switch configu ration pa rameters to the switch.
4 – Managing Switches Restoring a Switch 59022-1 1 A 4-37 0 3. Enter the archive file name or browse for the f ile. This archive file must be one that was produced by the SANsurfer Switch Manager Archive function.
4 – Managing Switches Restoring the Factory Default Configuration 4-38 59022-1 1 A 0 4.10 Restoring the Factory Default Configuration Y ou can restore the switch and po rt configuration settings to the factory default values. T o restore the factory configuration on a switch, open the Switch menu and select Restore Fact ory Defaults .
4 – Managing Switches Downloading a Support File 59022-1 1 A 4-39 0 4.1 1 Downloading a Support File The Download Support File menu option assembles all log files and switch memory data into a core d ump file (dump_support.tg z). This file can be se nt to technical support personnel for troubl eshooting switch problems.
4 – Managing Switches Installing Firmware 4-40 59022-1 1 A 0 4.12 Inst alling Firmware Installing firmware invo lves loading, unp ac king, and activating the firmware image on the switch.
4 – Managing Switches Displaying Hardware Status 59022-1 1 A 4-41 0 3. Click the Start button to begin the firmware load process. Y ou will be shown a message warning you that th e switch will be reset in order to activate t he firmware.
4 – Managing Switches Displaying Hardware Status 4-42 59022-1 1 A 0 Notes.
59022-1 1 A 5-1 Section 5 Managing Port s This section describes the following t a sks that manage ports and devices: Displaying Port Information Configuring Ports T esting Ports Graphing Port Performance 5.1 Displaying Port Information Port information is available primaril y in the faceplate display shown in Figu re 5-1 .
5 – Managing Ports Displaying Port Information 5-2 59022-1 1 A 0 5.1.1 Monitoring Port S t atus The faceplate display provides the following p ort related information: Port type Port operati.
5 – Managing Por ts Displaying Port Information 59022-1 1 A 5-3 0 5.1.1.2 Displaying Port Operational St ates T o display the operational st ate on each port in the faceplate display , open the View men u and select View Port States . T able 5-2 lists the possible operational states and their me anings.
5 – Managing Ports Displaying Port Information 5-4 59022-1 1 A 0 5.1.1.4 Displaying T ransceiver Media St atus T o display transceiver media st atus, open the V iew menu and select View Port Media . T able 5-4 lists the port media st ates and their meanings.
5 – Managing Por ts Displaying Port Information 59022-1 1 A 5-5 0 T able 5-5. Port Stat istics Data Window Entri es Entry Description S tart T ime The beginning of the period over which the st atistics apply . The start time for the Abso lute view is not applicable.
5 – Managing Ports Displaying Port Information 5-6 59022-1 1 A 0 Flow Errors Number of times a frame is received and all the switch ports receive buf fers are full. The normal Fabric Login exchange of flow contro l credit shou ld preven t this from o ccurring.
5 – Managing Por ts Displaying Port Information 59022-1 1 A 5-7 0 5.1.3 Port Information Dat a Window The Port Information dat a window displays det ail information for the selected port. T o open the Port Information dat a window , click the Port Info tab below the data window in the faceplate display .
5 – Managing Ports Displaying Port Information 5-8 59022-1 1 A 0 Administrative Port S tate The port state (Online, Of fline, Diagnostics, or Down) which has been set by the user . This state may be dif ferent from the configured administr ative state if the user has not saved it in the switch configuration.
5 – Managing Por ts Displaying Port Information 59022-1 1 A 5-9 0 Symbolic Name Port symbolic name Ext Credits Re quested Whether extended cr edits have been requested for port s. Credits to Donate Number of requested credits. Donor Group The donor group of the selected port.
5 – Managing Ports Configuring Ports 5-10 59022-1 1 A 0 5.2 Configuring Port s The port settings o r characteristics are c onfigured using the Port Properties dialog shown in Figure 5-2 . T o open the Port Properties dialog, select one or more p orts, open the Port menu and select Port Properties .
5 – Managing Por ts Configuring Ports 59022-1 1 A 5-1 1 0 5.2.1 Changing Port Administrative St ates The port administrative st ate determines the operat ional state of a po rt. The port administrative st ate exists in two forms: the configured administrat ive state and the current administrative st ate.
5 – Managing Ports Configuring Ports 5-12 59022-1 1 A 0 5.2.2 Changing Port Speeds Ports are ca pable of transmit ting and receiving at 1-Gbp s or 2-Gbps. The ports can be configured for either transmissi on speed or to sense the transmission speed of the device to which it is connected.
5 – Managing Por ts Configuring Ports 59022-1 1 A 5-13 0 5.2.3 Changing Port T ypes The ports can be configured to self-discover the pro per type to match the device or switch to which it is connected. Ta b l e 5 - 9 describes the port types. T o change the port type, do the following: 1.
5 – Managing Ports Using the Extended Credits Wizard 5-14 59022-1 1 A 0 5.2.5 Device Scan The Device Scan feature queries the connected device during login for FC-4 descriptor information. Disable this p arameter only if the scan creates a conflict with the connected device.
5 – Managing Por ts Using the Extended Credits Wizard 59022-1 1 A 5-15 0 3. Designate Donor Ports: Select availa ble ports and click >> to move the port into the Selected Donor Port column shown in Figure 5-3 . Match the number of ports nee ded with the number of desig nated donor port s.
5 – Managing Ports Resetting a Port 5-16 59022-1 1 A 0 5.4 Resetting a Port The Reset Port option reinitializes the port using the saved configuration. T o reset a port, do the following: 1. In the faceplate display , select the ports to be rese t. 2.
5 – Managing Por ts Testing Ports 59022-1 1 A 5-17 0 SFP level (External) - The SFP level test verifies port circuitry . The SFP level test sends a test f rame from the ASIC through the SerDes ch ip, through the SFP transceiver fitted with an external loopback plug, and back to the ASIC for the selected port s.
5 – Managing Ports Graphing Port Performance 5-18 59022-1 1 A 0 5.6 Graphing Port Performance SANsurfer Performance V iewer applic ation displays por t performance using graphs. SANsurfer Performance V iewer plots data communication rates and total errors for selected port s as shown in Figure 5-5 .
5 – Managing Por ts Graphing Port Performance 59022-1 1 A 5-19 0 This section describes how to do the following: S tarting SANsurfer Perfo rmance Vi ewer Exiting SANsurfer Performance V iewe.
5 – Managing Ports Graphing Port Performance 5-20 59022-1 1 A 0 5.6.2 Exiting SANsurfer Performance V iewer T o exit a SANsurfer Performance Viewer session, ope n the File menu and select Exit . The current fabric view is automatically saved to yo ur default performance view file upon exit, if you have defined an encryption key .
5 – Managing Por ts Graphing Port Performance 59022-1 1 A 5-21 0 In your next SANsurfer Performance V iew er session, the Load Default V iew File dialog shown in Figure 5-7 prompt s you to load the default performance view file and to specify its e ncryption key , if there is one.
5 – Managing Ports Graphing Port Performance 5-22 59022-1 1 A 0 5.6.4 Changing the Default Performanc e View File Encryption Key T o change the encryption key for the default performance view file, do the following: 1. Open the File menu and select Save Default Performance Vie w File to open the Save Default Perfo rmance View File dialog.
5 – Managing Por ts Graphing Port Performance 59022-1 1 A 5-23 0 5.6.6 Setting the Polling Frequency SANsurfer Performance V i ewer updates the graphs once per second by default. T o change this polling frequency , do the following: 1. Open the Graph menu, and select Set Polling Frequency to open the Se t Graph Polling Frequency dialog.
5 – Managing Ports Graphing Port Performance 5-24 59022-1 1 A 0 5.6.7.1 Arranging Graphs in the Display T o arrange and size graphs in the display , open the Window me nu and select Cascade , Tile , or Close Al l . Cascade overlaps the graphs so that all gr aphs are at least partially visible.
5 – Managing Por ts Graphing Port Performance 59022-1 1 A 5-25 0 T o modify the graph options, do the following: 1. Choose the units for the graph: Select the Show Bytes Data on Graph check box to plot dat a in KBytes/second Select the Show Frames Data on Graph check box to plot data in frames/second.
5 – Managing Ports Graphing Port Performance 5-26 59022-1 1 A 0 5.6.7.3 Setting Global Graph T ype The Set Global Graph T ype option enables y ou to view port activity using two types of graphs: Line Graph - plots continuous port acti vity in horizont al line format.
59022-1 1 A A-1 Appendix A Command Line Interface The command line interface (CLI) enable s you to perform a variety of fabric a nd switch management t asks through an Ethernet or a serial port connection. This section describes the following: Logging On to a Switch User Account s Working with Switch Configurations Commands A.
A – Command Line Interface User Accounts A-2 59022-1 1 A 0 A.2 User Account s Switches come from the factory with t he following user account already d efined: Account name: admin Password: password Authority: Admin This user account provides fu ll access to the switch and its configuratio n.
A – Command Line Interface Working with Switch Configurations 59022-1 1 A A-3 0 A.3.1 Modifying a Configuration A switch supports up to 10 configurati ons including the defau lt configuration. Each switch configuration contains swit ch, port, port threshold alarm, and zoning configuration component s.
A – Command Line Interface Working with Switch Configurations A-4 59022-1 1 A 0 A.3.2 Backing up and Restoring Switch Configurations Backing up and restoring a configuratio n is useful to protect your work or for use as a template in configu ring other switches.
A – Command Line Interface Working with Switch Configurations 59022-1 1 A A-5 0 The restore operation begins wit h FTP to upload the configuration file from the workstation to the switch, then finishes with a T elnet session and the Config Restore command.
A – Command Line Interface Commands A-6 59022-1 1 A 0 A.4 Commands The command synt ax is as follows: command key word keyword [value] keyword [value1] [value2] The Command is followed by one or more keyw ords. Consider the following rules and conventions: Commands and keywords are case insensitive.
A – Command Line Interface Commands 59022-1 1 A A-7 0 The command set performs monitoring and configuration t asks. Commands related to monitoring t asks are availabl e to all account names. Commands re lated to configuration tasks ar e available only within an a dmin session.
A – Command Line Interface Admin Command A-8 59022-1 1 A 0 Admin Command Opens and closes an Admin session. The Admin session provides comma nds that change the fabric and swit ch confi gurations. Only one Admin session can be open on the switch at any time.
A – Command Line Interface Alias Command 59022-1 1 A A-9 0 Alias Command Creates a named set of port s/devices. Aliases make it easier to assign a set of ports/devices to many zon es.
A – Command Line Interface Alias Command A-10 59022-1 1 A 0 members [alias] Displays all members of the alias given by [alias]. This keyword does not require an admin session. remove [alias] [member_list] Removes the ports/d evices given by [member_l ist] from the alia s given by [alias].
A – Command Line Interface CIM Command 59022-1 1 A A-1 1 0 CIM Command Manages CIM listener and subscription confi gurations on the switch. Refer to the ”CIMListener Command” on page A-12 for information about creating and modifying CIM listeners.
A – Command Line Interface CIMListener Command A-12 59022-1 1 A 0 CIMListener Command Configures CIM indication service listeners and ad ds s ubscriptions to listeners. Refer to the ”CIMSubscription Command” on pag e A-14 for information about configuring subscriptions.
A – Command Line Interface CIMListener Command 59022-1 1 A A-13 0 Examples The following is an example of the CIMListe ner Create command: SB5602-91.54 (admin-cim) #> cimlistener create listener_1 A list of attributes with formatting and current values will follow.
A – Command Line Interface CIMSubscription Command A-14 59022-1 1 A 0 CIMSubscription Command Creates, edit s, or removes CIM subscriptions. Authority Admin session and a CIM Edit session. Refer to the ”CIM Command” o n page A-1 1 for information ab out opening a CIM edit session.
A – Command Line Interface CIMSubscription Command 59022-1 1 A A-15 0 Examples The following is an example of the CIMSub scription Create command: SANbox2 (admin-cim) #> cimsubscription create subscription_1 A list of attributes with formatting and current values will follow.
A – Command Line Interface Config Command A-16 59022-1 1 A 0 Config Command Manages the Fibre Channel con figurations on a switch. For information ab out setting the port and switch configu rations, refer to the ”Set Config Command ” on page A-6 0 .
A – Command Line Interface Config Command 59022-1 1 A A-17 0 restore Restores configuration settings to an out-of-band switch from a backup file named configdata , which must b e first uploaded on the switch using FTP . Y ou create the backup file using the Config Backup command.
A – Command Line Interface Config Command A-18 59022-1 1 A 0 The following is an example of how to cre ate a backup file (configdata) an d download the file to the workst ation.
A – Command Line Interface Create Command 59022-1 1 A A-19 0 Create Command Creates support files for troublesho oting switch problems, and certificates for secure communications for SANsurfer Switch Man ager . Authority Admin session Synt a x create certificate support Keywords certificate Creates a security certificate on the switch.
A – Command Line Interface Create Command A-20 59022-1 1 A 0 Would you like to continue downloading support file? (y/n) [n]: y Connected to 10.20.33.130 (10.20.33.130). 220 localhost.localdomain FTP server (Version wu-2.6.1-18) ready. 331 Password required for johndoe.
A – Command Line Interface Create Command 59022-1 1 A A-21 0 The following is an example of the Create Certificate command: SANbox2 (admin) #> create certificate The current date and time is day mon date hh:mm:ss UTC yyyy. This is the time used to stamp onto the certificate.
A – Command Line Interface Date Command A-22 59022-1 1 A 0 Date Command This command displays or set s the system date and time. T o set the date and time the information string must be provid ed in this format: MMDDhhmmCCYY . The new date and time t akes effect immediately .
A – Command Line Interface Firmware Install Command 59022-1 1 A A-23 0 Firmware Inst all Command Downloads firmware from a remote host to the switch, installs the firmware, then resets the switch (with out a power-on self test) to activa te the firmware.
A – Command Line Interface Group Command A-24 59022-1 1 A 0 Group Command Creates group s, manages membership within the group, and manage s the membership of gr oups in sec urity sets . Authority Admin session and a Security Edit session. Refe r to the ”Security Command” on page A-5 2 for information about st arting a Security Edit session.
A – Command Line Interface Group Command 59022-1 1 A A-25 0 Keywords add [group] Initiates an editing session in which to spe cify a group member and its attributes for the existing group given by [group]. ISL, Port, and MS member attributes are described in T able A-5 , Ta b l e A - 6 , and T able A-7 respectively .
A – Command Line Interface Group Command A-26 59022-1 1 A 0 T able A-6. Port Group Member Attributes Attribute Description Member Port worldwide name for the N_Port device that would attach to the switch. A member cannot belong to more than one gro up.
A – Command Line Interface Group Command 59022-1 1 A A-27 0 copy [group_source] [group_destination] Creates a new grou p named [group_destination] and copies the membership into it from the group given by [group_source]. create [group] [type] Creates a group with the name given by [group] with the type given by [type].
A – Command Line Interface Group Command A-28 59022-1 1 A 0 edit [group] [member] Initiates an editing session in which to change the attributes o f a worldwide name given by [member] in a group given by [gro up]. Member attributes that can be changed are described in T able A-8 : T able A-8.
A – Command Line Interface Group Command 59022-1 1 A A-29 0 list Displays a list of all groups and the security set s of which they are members. This keyword is available without an Admin sessio n. members [group] Displays all members of the group given by [group].
A – Command Line Interface Group Command A-30 59022-1 1 A 0 Examples The following is an example of the Gr oup Add command: SANbox2 (admin-security) #> group add Group_1 A list of attributes with.
A – Command Line Interface Group Command 59022-1 1 A A-31 0 The following is an exampl e of th e Group List command: SANbox2 #> group list Group SecuritySet ----- ----------- group1 (ISL) alpha g.
A – Command Line Interface Hardreset C ommand A-32 59022-1 1 A 0 Hardreset Command Resets the switch and performs a power-on self test. This reset disrupt s traffic, activates the pending firmware, and clears the alarm log. T o save the alarm log before resetting, refer to the ”Set Log Command” on p age A-71 .
A – Command Line Interface Help Command 59022-1 1 A A-33 0 Help Command Displays a brief description of the specifie d command, its keywords, and usage. Authority None Synt a x help [command] [keyword] Keywords [command] Displays a summary of the comman d given by [command] and it s keywords.
A – Command Line Interface History Command A-34 59022-1 1 A 0 History Command Displays a numbered list of the previously e ntered commands from which you can re-execute selected commands.
A – Command Line Interface Hotreset Co mmand 59022-1 1 A A-35 0 Hotreset Command Resets the switch for th e purpose of activating t he pending firmware withou t disrupting traf fic. This command terminates all management session s, saves all configuration information, a nd clears the event log.
A – Command Line Interface Image Command A-36 59022-1 1 A 0 Image Command Manages and insta lls switch firmware. Authority Admin session Synt a x image cleanup fetch [account_name] [ ip_address] [file_source] [file_destination] inst all list unpack [file ] Keywords cleanup Removes all firmware image files from the switch.
A – Command Line Interface Image Command 59022-1 1 A A-37 0 Notes T o provide consistent performance throughout the fabric, ensure that all switches are running the same version of firmware.
A – Command Line Interface Image Command A-38 59022-1 1 A 0 9. Open an Admin session to acquire th e necessary authority . SANbox2 $>admin start 10. Display the list of firmware image files on the switch to confirm that the file was loaded. SANbox2 (admin) $>image list 1 1.
A – Command Line Interface Lip Command 59022-1 1 A A-39 0 Lip Command Reinitializes the specified loop port. Authority Admin session Synt a x lip [port_number] Keywords [port_number] The number of the port to be reinitialize d. Ports are numbered beginning with 0.
A – Command Line Interface Passwd Command A-40 59022-1 1 A 0 Passwd Command Changes a user account’ s password. Authority Admin account name and an admin se ssion to change another acco unt’s password; Y ou can change you own password with out an Admin session.
A – Command Line Interface Ping Command 59022-1 1 A A-41 0 Ping Command Initiates an attempt to communica te with another switch over an Ethernet net work and reports the result. Authority None Synt a x ping [ip_address] Keywords [ip_address] The IP address of the switch to qu ery .
A – Command Line Interface Ps Command A-42 59022-1 1 A 0 Ps Command Displays current system process information. Authority None Synt a x ps Examples The following is an example of the Ps command: SANbox2 #> ps PID PPID %CPU TIME ELAPSED COMMAND 338 327 0.
A – Command Line Interface Quit Command 59022-1 1 A A-43 0 Quit Command Closes the T elnet session. Authority None Synt a x quit, exit, or logout Notes Y ou can also enter Control-D to close the T elnet session.
A – Command Line Interface Reset Command A-44 59022-1 1 A 0 Reset Command Resets the switch configuration p arameters. If you omit the keyword, the de fault is Reset Switch.
A – Command Line Interface Reset Com mand 59022-1 1 A A-45 0 services Resets the switch se rvices configuration to the default values as described in T able A-15 . snmp Resets the SNMP conf iguration settings to the factory default valu es. Refer to T able A-13 for SNMP configuration default values.
A – Command Line Interface Reset Command A-46 59022-1 1 A 0 Notes The following tab les specify the various factory default settings: Enter the Show Config Switch comm and to display switch configuration values.
A – Command Line Interface Reset Com mand 59022-1 1 A A-47 0 Enter the Show Config Port command to display port co nfiguration values. T able A-10. Port Configuration Defaults Parameter Default Admi.
A – Command Line Interface Reset Command A-48 59022-1 1 A 0 Enter Show Config Threshold comman d to display threshold alarm configuration values. Enter the Show Config Zoning command to display zoning configuration values.
A – Command Line Interface Reset Com mand 59022-1 1 A A-49 0 Enter the Show Setup SNMP command to display SNMP co nfiguration values. T able A-13. SNMP Configuration Defaults Parameter Default SNMPE.
A – Command Line Interface Reset Command A-50 59022-1 1 A 0 Enter the Show Setup Radius command to display RADI US configuration values. Enter the Show Setup Services command to display switch service configuration values.
A – Command Line Interface Reset Com mand 59022-1 1 A A-51 0 Enter the Show Setup System command to display system configuration values. Enter the Show Config Security command to d isplay security configuration values. T able A-16. System Configuration Defaults Parameter Default Ethernet Network Discovery S tatic Ethernet Network IP Address 10.
A – Command Line Interface Security Command A-52 59022-1 1 A 0 Security Command Opens a Security Edit session in which to manage the securit y database o n a switch. Refer to the ”Group Comman d” on page A-24 and the ”Securityset Command” on page A-56 .
A – Command Line Interface Security Command 59022-1 1 A A-53 0 history Displays history information about the security d atabase and the active securit y set including the account name tha t made changes and when those changes were made. This keyword does not require an Ad min session.
A – Command Line Interface Security Command A-54 59022-1 1 A 0 The following is an example of the Security Histo ry command: SB211.192 #> security history Active Database Information ------------.
A – Command Line Interface Security Command 59022-1 1 A A-55 0 The following is an example of the Secu rity List command: SANbox2 (admin-security) #> security list SB211.192 #> security list Active Security Information SecuritySet Group GroupMember ----------- ----- ----------- No active securityset defined.
A – Command Line Interface Securityset Command A-56 59022-1 1 A 0 Securityset Command Manages security sets in the secu rity database. Authority Admin session and a Security Edit session. Refe r to the ”Security Command” on page A-5 2 for information about st arting a Security Edit session.
A – Command Line Interface Security set Command 59022-1 1 A A-57 0 del ete [security_set] Deletes the security set given by [securit y_set ]. If the specified security set is active, the command is suspended until th e security set is deactivated.
A – Command Line Interface Set Command A-58 59022-1 1 A 0 Set Command Sets a vari ety of switch p arameters. Authority Admin session for all keywords except Alarm, Beacon , and Pagebreak which are available without an Admin session.
A – Command Line Interface Set Comman d 59022-1 1 A A-59 0 p agebreak [st ate] S pecifies how much information is displayed on the screen at a time according to the value given by [ state]. This keyword does not require an admin session. [state] can be one of the following: on Limits the display o f information to 20 lines at a time.
A – Command Line Interface Set Config Command A-60 59022-1 1 A 0 Set Config Command Sets switch, port, port thre shold alarm, security , and zoning configuration parameters. The changes you make with th is comman d are not ret ained when you reset or power cycle the switch unless you save them using the Config Save command.
A – Command Line Interface Set Config Command 59022-1 1 A A-61 0 SymbolicPortNa me Desc riptive name for the po rt. The na me can be up to 32 characters excluding #, semico lon (;), and comma ( ,). The default is Port n where n is the port number . ALFairness Arbitration loop fairness.
A – Command Line Interface Set Config Command A-62 59022-1 1 A 0 security Initiates an editing session in which to change the security settings. Th e system displays each parameter one line at a time and prompts you for a value. For each LCFEnable Link control frame pr ef erence routing .
A – Command Line Interface Set Config Command 59022-1 1 A A-63 0 parameter , enter a new value or press the Enter key to accept the current value shown in brackets. En ter “q” or "Q" to end the editing session. Ta b l e A - 1 9 describes the Set Config Security p arameters.
A – Command Line Interface Set Config Command A-64 59022-1 1 A 0 SymbolicName Descriptive name for the switch. The name can be up to 32 characters excluding #, semicolon (;), and comma (,). The default is SANbox2. R_A_TOV Resource Allocation Timeout V alue.
A – Command Line Interface Set Config Command 59022-1 1 A A-65 0 threshold Initiates a configuration session by which to gene rate and log alarms for selected events. The syste m displa ys each event, its triggers, and sampling window one line at a time and prompt s you for a value.
A – Command Line Interface Set Config Command A-66 59022-1 1 A 0 zoning Initiates an editing session in which to change switch zoning attributes. Th e system displays each p arameter one line at a time and prompt s you for a value. For each pa rameter , enter a new value or press the Enter key to accept the current value shown in bracket s.
A – Command Line Interface Set Config Command 59022-1 1 A A-67 0 ALFairness (True / False) [False ] DeviceScanEnable (True / False) [True ] ForceOfflineRSCN (True / False) [False ] ARB_FF (True / Fa.
A – Command Line Interface Set Config Command A-68 59022-1 1 A 0 The following is an example of the Set Config Security comma nd: SANbox2 #> admin start SANbox2 (admin) #> config edit SANbox2 (admin-config) #> set config security A list of attributes with formatting and current values will follow.
A – Command Line Interface Set Config Command 59022-1 1 A A-69 0 The following is an example of the Set Config Thre shold command: SANbox2 #> admin start SANbox2 (admin) #> config edit SANbox2 (admin-config) #> set config threshold A list of attributes with formatting and current values will follow.
A – Command Line Interface Set Config Command A-70 59022-1 1 A 0 The following is an example of the Set Config Zon ing command. SANbox2 #> admin start SANbox2 (admin) #> config edit SANbox2 (admin-config) #> set config zoning A list of attributes with formatting and current values will follow.
A – Command Line Interface Set Log Command 59022-1 1 A A-71 0 Set Log Command S pecifies the event s to record in the event log and display on the screen. Y ou determine what event s to record in the switch event log using the Component, Level, and Port keywords.
A – Command Line Interface Set Log Command A-72 59022-1 1 A 0 None Monitor none of the component eve nts. Other Monitors other mi scellaneous event s. Port Monitors all port event s. SNMP Monitors all SNMP events. Switch Monitors switch management event s.
A – Command Line Interface Set Log Command 59022-1 1 A A-73 0 level [filter] S pecifies the severity level given by [filter ] to use in monitoring and logg ing events for the specified component s or ports. [filter] can be one o f the following values: Critical Monitors critical event s.
A – Command Line Interface Set Log Command A-74 59022-1 1 A 0 Notes In addition to critical, warn, and informative severity levels, the highest even t severity level is alarm. The alarm level describ es events that are disruptive to the administration or opera tion of a fabric and require administrator intervention.
A – Command Line Interface Set Port Command 59022-1 1 A A-75 0 Set Port Command Sets port st ate and speed for the specified port temporarily until the next switch reset or new configuration activation. Th is command also clears port counters. Authority Admin session except for the Clear keyword.
A – Command Line Interface Set Port Command A-76 59022-1 1 A 0 st ate [state] S pecifies one of the following adminis trative states fo r the specified port: Online Places the port online. This activates an d prepares the port to send data. Offline Places the port of fline.
A – Command Line Interface Set Setup Command 59022-1 1 A A-77 0 Set Setup Command Manages configuration settings for Remote Aut hentication Dial-In User Service (RADIUS) servers, switch services , SNMP , and system configurations.
A – Command Line Interface Set Setup Command A-78 59022-1 1 A 0 UserAuthServer Enab le (T rue) or disable (False) this server for user account authentication. A user authentication RADIUS ser ver requires a secure management con nection (SSL). The default is T rue.
A – Command Line Interface Set Setup Command 59022-1 1 A A-79 0 services Prompts you in a line-by-lin e fashion to enable o r disable switch services. T able A-24 describes the switch service paramet ers. For each parameter , enter a new value or press the Enter key to accept the current value shown in brackets.
A – Command Line Interface Set Setup Command A-80 59022-1 1 A 0 EmbeddedGUIEnabled Enab les (T rue) or disables (False) the SANsurfer Switch Manager web applet. The web applet ena bles you to point at a switch with an intern et browser and ru n SANsurfer Switch Manager through the browser .
A – Command Line Interface Set Setup Command 59022-1 1 A A-81 0 snmp Prompts you in a line-by-lin e fashion to change SNMP configuration settings. T able A-25 describes the SNMP fields. For each para meter , enter a new value or press the Enter key to accept the current value shown in bracket s .
A – Command Line Interface Set Setup Command A-82 59022-1 1 A 0 system Prompts you in a line-by-lin e fashion to change system conf iguration settings. T able A-26 describes the system configuration fields. For each parameter , enter a new value or press the Enter key to accept the current value shown in brackets.
A – Command Line Interface Set Setup Command 59022-1 1 A A-83 0 LocalLogEnabled Enables (T rue) or disables (False) the saving of log information on the switch. The default is T rue. RemoteLogEnabled Enables (T rue) or disables (False) the recor ding of the switch event log on a remote host that support s the syslog protocol.
A – Command Line Interface Set Setup Command A-84 59022-1 1 A 0 Examples The following is a n example of the Set Setup RADIUS command: SANbox2 (admin) #> set setup radius A list of attributes with formatting and current values will follow. Enter a new value or simply press the ENTER key to accept the current value.
A – Command Line Interface Set Setup Command 59022-1 1 A A-85 0 The following is an example of the Set Setu p SNMP command: SANbox2 #> admin start SANbox2 (admin) #> set setup snmp A list of attributes with formatting and current values will follow.
A – Command Line Interface Set Setup Command A-86 59022-1 1 A 0 The following is an example of the Set Setu p System command: SANbox2 (admin) #> set setup system A list of attributes with formatting and current values will follow. Enter a new value or simply press the ENTER key to accept the current value.
A – Command Line Interface Show Command 59022-1 1 A A-87 0 Show Command Displays fabric, switch, and port operational inf ormation. Authority None Synt a x show about alarm [option] audit broadcast .
A – Command Line Interface Show Command A-88 59022-1 1 A 0 alarm [option] Displays the alarm log and session disp lay setting. If you omit [optio n], the command displays the last 200 alarm entries. The alarm log is cleared when the switch is reset or power cycled.
A – Command Line Interface Show Command 59022-1 1 A A-89 0 log [option] Displays log entries. Refer to the ”Show L og Command” on page A-106 . The log is cleared when the switch is reset or power cycled.
A – Command Line Interface Show Command A-90 59022-1 1 A 0 port [port_number] Displays operational information for t he port given by [port_ number]. Ports a re numbered beginning with 0. If [po rt number] is omitted, information is d isplayed for all ports.
A – Command Line Interface Show Command 59022-1 1 A A-91 0 LIP_F8_AL_PS This LIP denotes a loop failure detecte d by the L_Port identified by AL_PS. LIP_F7_F7 A loop initialization primit ive frame used to acquire a valid AL_P A.
A – Command Line Interface Show Command A-92 59022-1 1 A 0 post log Displays the Power On Self T est (POST) log which contains results from th e most recently failed POST . setup [option] Displays setup attributes for the system, SNMP , and the switch manufacturer .
A – Command Line Interface Show Command 59022-1 1 A A-93 0 Whoami Zoneset (Active, List) Zoning (History , Limits, List) switch Displays switch operational information. T able A-28 describes the switch operational p arameters. T able A-28.
A – Command Line Interface Show Command A-94 59022-1 1 A 0 timezone Displays the current time zone setting. topology Displays all connected devices. users Displays a list of logged-in users. This is equivalent t o the User List command. version Displays an introductory set of information about ope rational attributes of the switch.
A – Command Line Interface Show Command 59022-1 1 A A-95 0 Examples The following is an example of the Show Chassis co mmand: SANbox2 #> show chassis Chassis Information ------------------- Board.
A – Command Line Interface Show Command A-96 59022-1 1 A 0 The following is an example of the Show FDMI command: SANbox2 #> show fdmi HBA ID PortID Manufacturer Model Ports -------- ------ ------.
A – Command Line Interface Show Command 59022-1 1 A A-97 0 The following is an example of th e Show NS (local d omain) command: SANbox2 #> show ns Seq Domain Port Port No ID ID Type COS PortWWN N.
A – Command Line Interface Show Command A-98 59022-1 1 A 0 The following is an example of the Show Inte rface command: SANbox2 #> show interface eth0 Link encap:Ethernet HWaddr 00:C0:DD:00:BD:ED inet addr:10.20.68.107 Bcast:10.20.68.255 Mask:255.
A – Command Line Interface Show Command 59022-1 1 A A-99 0 The following is an example of the Show Port command: SANbox2 #> show port 1 Port Number: 1 ------------ AdminState Online OperationalSt.
A – Command Line Interface Show Command A-100 59022-1 1 A 0 The following is an example of the Show Switch co mmand: SANbox2 #> show switch Switch Information ------------------ SymbolicName sw .108 SwitchWWN 100000c0dd00bc56 SwitchType SANbox2-64 BootVersion Vx.
A – Command Line Interface Show Command 59022-1 1 A A-101 0 The following is an example of the Show T opology command for port 1: SANbox2 #> show topology 1 Local Link Information ---------------.
A – Command Line Interface Show Command A-102 59022-1 1 A 0 The following is an example of the Show V ersion command: SANbox2 #> show version *****************************************************.
A – Command Line Interface Show Config Command 59022-1 1 A A-103 0 Show Config Command Displays switch, port, alarm threshold, security , and zoning for the current configuration.
A – Command Line Interface Show Config Command A-104 59022-1 1 A 0 MSEnabled True NoClose False IOStreamGuard Disabled VIEnabled False PDISCPingEnable True The following is an example of the Show Co.
A – Command Line Interface Show Config Command 59022-1 1 A A-105 0 The following is an example of the Show Config Threshold co mmand: SANbox2 #> show config threshold Configuration Name: default .
A – Command Line Interface Show Log Comm and A-106 59022-1 1 A 0 Show Log Command Displays the content s of the log or the p arameters used to create and display entries in the log. The log cont ains a maximum of 1200 entries. When the log reaches its e ntry capacity , subsequent entries overwrite the existing entries, beginning with the oldest.
A – Command Line Interface Show Log Command 59022-1 1 A A-107 0 Zoning Monitors zoning conflict event s. display [filter] Displays log events on the screen according to the component or severity level filter given by [filter]. [filter] can be one of the following: Info Displays all informative events.
A – Command Line Interface Show Log Comm and A-108 59022-1 1 A 0 Examples The following is an example of the Show Log Component command: SANbox2 #> show log component Current settings for log ---.
A – Command Line Interface Show Perf Command 59022-1 1 A A-109 0 Show Perf Command Displays port performance in frames/second and byt es/second. If you omit the keyword, the command displays dat a transmitted (out), data received (in), and total dat a transmitted and received in frames/second and bytes per second.
A – Command Line Interface Show Perf Command A-1 10 59022-1 1 A 0 Examples The following is an example of the Show Perf command: SANbox2 #> show perf Port Bytes/s Bytes/s Bytes/s Frames/s Frames/.
A – Command Line Interface Show Setup Command 59022-1 1 A A - 111 0 Show Setup Command Displays the current SNMP and system settin gs. Authority None Synt a x show setup mfg radius services snmp system Keywords mfg Displays manufacturing information about the switch .
A – Command Line Interface Show Setup Command A-1 12 59022-1 1 A 0 The following is an example of the Show Setup Services command: SANbox2 #> show setup services System Services -----------------.
A – Command Line Interface Show Setup Command 59022-1 1 A A-1 13 0 The following is an example of the Show Setup Snmp command: SANbox2 #> show setup snmp SNMP Information ---------------- SNMPEnabled True Contact <sysContact undefined> Location N_107 System Test Lab Description SANbox2-64 FC Switch Trap1Address 10.
A – Command Line Interface Show Setup Command A-1 14 59022-1 1 A 0 The following is an example of the Show Setup System command: SANbox2 #> show setup system System Information ------------------ Eth0NetworkDiscovery Static Eth0NetworkAddress 10.
A – Command Line Interface Shutdown Command 59022-1 1 A A-1 15 0 Shut down Command T erminates all data transfers on the switch a t convenient points a nd closes the T elnet session.
A – Command Line Interface Test Command A-1 16 59022-1 1 A 0 T est Command T ests ports using intern al (SerDes level), external (transceiver), and online loopback tests. I nternal and external test s require that the port be placed in diagnostic mode.
A – Command Line Interface Test Command 59022-1 1 A A-1 17 0 Examples T o run an internal or external port test, do the following: 1. T o start an admin sessio n, enter the following command and p ress the Enter key . admin start 2. Place the port in Diagnostics mode, ent er the following command ( x = port number) and press the Enter key .
A – Command Line Interface Test Command A-1 18 59022-1 1 A 0 The online loopback (node-to-node) test requires that port b e online and connected to a remote device. T o run the online loopback test, do the following : 1. T o start an admin sessio n, enter the following command and p ress the Enter key .
A – Command Line Interface Uptime Command 59022-1 1 A A-1 19 0 Uptime Command Displays the elap sed up time since the switch was last reset and reset method. A hot reset or non-disruptive firmware activatio n does not reset the elap sed up time reported by this command.
A – Command Line Interface User Command A-120 59022-1 1 A 0 User Command Administers and displays user account s. Authority Admin account name and an Admin session. The Account s and List keywords are available to all account names without an Admin session.
A – Command Line Interface User Command 59022-1 1 A A-121 0 Examples The following is an example of the User Accou nts command: SANbox2 (admin) #> user accounts Current list of user accounts ----.
A – Command Line Interface User Command A-122 59022-1 1 A 0 The following is an example of the User Delete command : SANbox2 (admin) #> user del user3 The user account will be deleted.
A – Command Line Interface Whoami Command 59022-1 1 A A-123 0 Whoami Command Displays the account name, session numb er , and switch domain ID for the T elnet session.
A – Command Line Interface Zone Command A-124 59022-1 1 A 0 Zone Command Manages zones and zone membership on a switch. Authority Admin session and a Zoning Edit sessio n. Refer to the ”Zoning Co mmand” on page A-1 30 for information about st arting a Zoning Edit session.
A – Command Line Interface Zone Command 59022-1 1 A A-125 0 list Displays a list of all zones and the zone set s of which they are components. This keyword does not require an Admin session. members [zone] Displays all members of the zone given by [zon e].
A – Command Line Interface Zone Command A-126 59022-1 1 A 0 Examples The following is an example of the Zone List command: SANbox2 #> zone list Zone ZoneSet ------------------- wwn_b0241f zone_se.
A – Command Line Interface Zone Command 59022-1 1 A A-127 0 The following is an example of th e Zone Zonesets command: SANbox2 #> zone zonesets zone1 Current List of ZoneSets for Zone: zone1 ----.
A – Command Line Interface Zoneset Command A-128 59022-1 1 A 0 Zoneset Command Manages zone sets and component zones across the fabric. Authority Admin session and a Zoning Edit sessio n. Refer to the ”Zoning Co mmand” on page A-1 30 for information about st arting a Zoning Edit session.
A – Command Line Interface Zoneset Com mand 59022-1 1 A A-129 0 list Displays a list of all zone set s. This keyword does not require an Admin session. remove [zone_set] [zone_list] Removes a list of zones given by [zon e_list] from the zone set given by [zone_set].
A – Command Line Interface Zoning Command A-130 59022-1 1 A 0 Zoning Command Opens a Zoning Edit session in which to create and manage zone set s and zones. Refer to the ”Zone Command” on page A-124 a nd the ”Zoneset Command” on page A-1 28 .
A – Command Line Interface Zoning Command 59022-1 1 A A-131 0 history Displays a history of zoning modification s. This keyword does not requir e an Admin session.
A – Command Line Interface Zoning Command A-132 59022-1 1 A 0 Examples The following is an example of the Zoning Edit comma nd: SANbox2 #> admin start SANbox2 (admin) #> zoning edit SANbox2 (admin-zoning) #> . . SANbox2 (admin-zoning) #> zoning cancel Zoning edit mode will be canceled.
A – Command Line Interface Zoning Command 59022-1 1 A A-133 0 The following is an exampl e of th e Zoning List command: SANbox2 #> zoning list Active ZoneSet Information ZoneSet Zone ZoneMember -.
A – Command Line Interface Zoning Command A-134 59022-1 1 A 0 Notes.
59022-1 1 A Glossary-1 Glossary Access Control List Zone Access Control List zoning divides the fabric for purposes of controlling discovery and inbound traf fic. Active Zone Set The zone set that define s the current zoning for the fabric. Active Firmware The firmware image on the switch that is in use.
Glossary-2 59022-1 1 A SANbox2-8c/16 Switch Manage ment User’s Guide 0 Class 3 Service A service which multiplexes frames at frame boundaries to or from one or more N_Ports without acknowledg ment. Configured Zone Set s The zone set s stored on a switch excluding the active zone set.
SANbox2-8c/16 Switch Management User’s Guide 0 59022-1 1 A Glossary-3 In-Order-Delivery A feature that requires that frames be received in the same order in which they were sent. Input Power LED A chassis LED that indicates that the switch logic circuitry is receiving proper DC voltages.
Glossary-4 59022-1 1 A SANbox2-8c/16 Switch Manage ment User’s Guide 0 Power On Self T est (POST) Diagnostics that the switch chassis performs at start up. Princip al Switch The switch in the fabric that manages domain ID assignment s. SANsurfer Switch Manager Switch management application.
59022-1 1 A Index-1 Index A access control list zone 3-39, 3-53 account name 3-22 display A-120, A-123 factory A-2 active zone set 3-33, 3-39 Active Zoneset data window 3-33 Admin account name A-7 aut.
Index-2 59022-1 1 A SANbox2-8c/16 Switch Manage ment User’s Guide 0 configuration activate A-16 archive 4-35 backup A-16 copy A-16 delete A-16 edit A-16 list A-16 reset A-44 restore 4-36, A-17 save .
SANbox2-8c/16 Switch Management User’s Guide 0 59022-1 1 A Index-3 event logging by component A-71, A-106 by port A-73, A-107 by severity level A-107 display A-106 restore defaults A-73 save setting.
Index-4 59022-1 1 A SANbox2-8c/16 Switch Manage ment User’s Guide 0 group add member 3-15, A-25 copy A-27 create 3-13, A-27 edit member attributes 3-16, A-28 list A-29 list members A-29 Management S.
SANbox2-8c/16 Switch Management User’s Guide 0 59022-1 1 A Index-5 M Management Server group A-27 service 4-28, A-80 manufacturer information A-111 mask address A-82 MD5 authentication A-26 media st.
Index-6 59022-1 1 A SANbox2-8c/16 Switch Manage ment User’s Guide 0 port administrative st ate 5-11, A-76 buffer credit s 5-14 configuration 5-10, A-60 configuration default s A-47 configuration dis.
SANbox2-8c/16 Switch Management User’s Guide 0 59022-1 1 A Index-7 SANsurfer Performance V iewer arrange graphs 5-24 customize graphs 5-24 display graphs 5-23 exit 5-20 preferences 5-22 start 5-19 S.
Index-8 59022-1 1 A SANbox2-8c/16 Switch Manage ment User’s Guide 0 Simple Network Management Protocol configuration 4-33, A-81 configuration display A-111 default s A-49 enable 3-19, 4-33 proxy 4-3.
SANbox2-8c/16 Switch Management User’s Guide 0 59022-1 1 A Index-9 time zone A-59 timeout Admin session A-82 T elnet session A-82 values 4-26 tool bar standard 2-22 zoning 3-43 topolo gy disp lay ar.
Index-10 59022-1 1 A SANbox2-8c/16 Switch Manage ment User’s Guide 0 zone merge description 3-55 failure 3-55 failure recovery 3-56 zone set activate 3-48, A-128 active 3-33, 3-39, A-130 add member .
An important point after buying a device Q-Logic 59022-11 A 4-13 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Q-Logic 59022-11 A 4-13 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Q-Logic 59022-11 A 4-13 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Q-Logic 59022-11 A 4-13 you will learn all the available features of the product, as well as information on its operation. The information that you get Q-Logic 59022-11 A 4-13 will certainly help you make a decision on the purchase.
If you already are a holder of Q-Logic 59022-11 A 4-13, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Q-Logic 59022-11 A 4-13.
However, one of the most important roles played by the user manual is to help in solving problems with Q-Logic 59022-11 A 4-13. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Q-Logic 59022-11 A 4-13 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
