Instruction/ maintenance manual of the product PLCD9MR Pyle
Go to page of 15
OWNER’S MANUAL Mobile Audio System • CD Player • PLL Synthesizer Stereo Radio • Compact Disc Player • Automatic Memory Storing • Full Detachable Panel • Preset Equalization • Electronic Shockpr oof (ESP) Function • Auxiliary Input Function • Remote Control www .
2 CONTENTS Installation ........................................... 3 T ake out screw befor e installation.........3 DIN Front-Mount (Method A) ................3 Installing the unit .................................3 Removing the unit ................
3 INST ALLA TION Notes: • Choose the mounting location where the unit will not interfere with the normal driving function of the driver . • Before finally installing the unit, connect the wiring temporarily and make sure it is all connected up properly and the unit and the system work properly .
grounding of the unit. Note to install the short threading terminal of the mounting bolt to the back of the unit and the other long threading terminal to the dashboard. 10. Reconnect the cable to the vehicle battery's negative (-) terminal. Then replace the outer trim ring and install the unit's front panel.
DIN REAR-MOUNT (Method B) If your vehicle is a Nissan, Toyota, follow these mounting instructions. Use the screw holes marked T (T oyota), N (Nissan) located on both sides of the unit to fasten the unit to the factory radio mounting brackets supplied with your vehicle.
USING THE DET ACHABLE FRONT P ANEL REMOVING THE FRONT P ANEL 1. Pr ess the release button (RELEASE) on the front panel and pull of f the front panel. 2. Keep fr ont panel into the case. INST ALLING THE FRONT P ANEL T o install the front panel, insert the panel into the housing and make sure the panel is properly installed.
7 WIRING CONNECTION FRONT Lch SPEAKER GREEN GREEN/BLACK MEMORY BACK-UP (B+) MAIN UNIT IGNITION SWITCH (ACC+) POWER ANTENNA RED GROUND (B–) YELLOW BLACK BLUE RCA CABLE ANTENNA CONNECTOR (GREY) Rch RE.
8 OPERA TION LOCA TION OF KEYS 24 7 9 14 3 6 15 5 8 4 11 10 25 2 1 23 22 21 20 18 13 19 17 12 16 26.
9 OPERA TION SWITCHING ON/OFF THE UNIT Switch on the unit by pressing any button (except button (7) and button (4)). When system is on, press button (9) to turn off the unit. F ACEPLATE RELEASE Press button (7) to detach the removable faceplate. SOUND ADJUSTMENT Press SEL button (10) to select the desir ed adjustment mode.
10 RADIO OPERA TION • SWITCHING TO RADIO MODE Press MODE button (6) shortly to select radio mode, the radio mode appears in the display together with the memory band and frequency . • SELECTING THE FREQUENCY BAND At radio mode, press BND/LOU (ENT) button (13) shortly to select the desired band.
11 OPERA TION • PLA YING ALL TRACKS IN RANDOM Press SHF button (23) to play all tracks on CD in random order . Press again to cancel the function. • EJECTING A DISC Press button (4) to stop CD playing and eject the disc from the disc slot (5).
12 REMOTE CONTROL HANDSET FUNCTION KEYS & CONTROL 1. PWR Power ON/OFF Button 2. DSP Display Button 3. SEL Sound Mode Select Button 4. VOL V olume Up Button 5. VOL V olume Down Button 6. BND (LOU) Band Select Button (When pressed shortly) Loudness Button (When pressed long) 7.
13 OPERA TION DISC NOTE A. Notes on discs: 1. Attempting to use non-standard shape discs (e.g. square, star , heart) may damage the unit. Be sure to use r ound shape CD discs only for this unit. 2. Do not stick paper or tape etc., onto the label side or the recor ding side of any discs, as it may cause a malfunction.
14 GENERAL P o wer Supply Requirements : DC 12 V olts, Negative Ground Chassis Dimensions : 178 (W) x 160 (D) x 50 (H) Tone Controls - Bass (at 100 Hz) : ± 10 dB - T reble (at 10 KHz) : ± 10 dB Maximum Output P ower : 4 x 40 W atts Current Drain : 5 Ampere (max.
TROUBLE SHOOTING Before going thr ough the check list, check wiring connection. If any of the problems persist after check list has been made, consult your nearest service dealer . Symptom Cause Solution No power . The car ignition switch is If the power supply is not on.
An important point after buying a device Pyle PLCD9MR (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Pyle PLCD9MR yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Pyle PLCD9MR - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Pyle PLCD9MR you will learn all the available features of the product, as well as information on its operation. The information that you get Pyle PLCD9MR will certainly help you make a decision on the purchase.
If you already are a holder of Pyle PLCD9MR, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Pyle PLCD9MR.
However, one of the most important roles played by the user manual is to help in solving problems with Pyle PLCD9MR. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Pyle PLCD9MR along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
