Instruction/ maintenance manual of the product LC-10 IR Provision-ISR
Go to page of 20
.
1 T able of Content: Chapter 1: Product Sum mary : 1.1 T echnical Parameters…… ……..… ……….……………. ………… ….2 1.2 Packa ge Content s…. …………… ……………… ……………. ……….3 1.3 Functio n descriptio n…………… ………… ………………….
2 Chapter 1:Product Summary: 1.1 T e chnical Parameters : Model numb er 4" High S peed Mini Dome Camera Optical focus 10X Image sensor 1/3"CCD Signal mod e P AL/NTSC Resolution 650TVL Optical focus Manual/Aut o, high performance DSP to util ize high continuous fo cusing funct ion.
3 1.2 Package Content s: 1. S peed Dome Camera – 1 Pcs 2. Wa ll Bracket – 1 Pcs 3. Ceiling Brac ket – 1 Pcs 4. Power Supp ly – 1 Pcs 5. User Manua l – 1 Pcs 6.
4 6. Lens C ontrol: (1) Zoom co ntrol Users can control the PTZ l ens in order to adjust the zoom level of the camera and get wide/narr ow view according to the scene. (2) Focus Control System default is auto-focus. The object in center of the screen will be the subject of focus.
5 10. Night M ode (color / Black & W hite conversi on) : Cameras with n ight m ode, automatic color / mon ochrome conversion mode, in accordanc e with c hanges in ambient light a utomatic c onversion CCD illumination. Such as: adequate lighting during the day du e to the use of general illumination to ensure colorful im ages.
6 DIP switch to “O N” means to “1”,DIP switch to "OFF" means "0". The baud rate and contro l protocol a s the followi ng table: NO.
7 248 OFF OFF O FF ON ON ON ON ON.
8 2.2 Dome cam e ra struct ure diagram: Figure 1 Figure 2 2.3 Bracket i nst allation diagram Figure 3.
9 Figure 4 Chapter 3 System OSD menu settings: 3.1Power-O n Self-T est : When power i s connected to the dome camera, the camera will move i n horizonta l and vertical di rect ions to confirm that motor s and belts are in order . The screen w ill show sy stem-related information.
10 3.2.2 Call pres et points : (1) Make sure the correct camera is se l ected in y our control ler . (2) Press the required preset number (in put s the designated preset) + PREVIE W * button, the camera will immediately mov e to the desired preset position.
1 1 3.4OSD Main Menu Once the dome camera is power on and finished self-testin g, call preset 95in order to acce ss the OD S main me nu as shown i n T able 3.1. MAINMEN U Menu funct ion descri ptions SYSTEM INFORMATIO N Displays ca m era basic in formation.
12 3.5 SYSTE M INFOR MA TION: SYSTEM IN FORMA TION Menu funct ion descri ptions COM 2400,N,8,1 Serial infor mation, display the dome camera ser ial port baud rate, parity , dat a bits, st op bits of informat ion. ADDRESS 1 Display t he current do me camera a ddress PROTOCOL PELCO- D Display t he current do me camera communicat ion protocol.
13 3.7 MOTIO N (PTZ) Sett ings: This menu is used to set PTZ parameters suc h as movement and orientat ion angles as s hown in the fo llowing t able: MOTION Menu funct ion descri ptions SET FRAME SCAN Set the sca n left and right limits. See More Det ails in sectio n 3.
14 3.7.4POWE R UP Setting s: This will define which action the dome camera will perfor m when it is powered on. (unless any other acti on was rece ived). Para meters in t he following t able: POWER U P M enu fun ction descri ptions NONE Don’t perfor m any action.
15 3.8P A TTERNS M enu: PATTERNS Menu funct ion descri ptions PATTER NNUMBER 1 S elect patter n number, within 1~4. PROGRAM PATT ERN To select patt ern scan l ine; O perations shown in sect ion 3.8.1. CLEAR C URRENT PA TTERN Clear current pattern scan line.
16 3.9 CAMERA (Zoom Module) Settings : CAMERA ID 000 Not in use ZOOM DIS PLA Y OFF Allow you t o remove the Zoom indicatio n display BLC OFF Backlight Compensat i on Contro l AGC MIDDLE Allows y ou to.
17 EXIT Exit the me nu setting. *in case you are setting-up the cruise using Provision-ISR DVR, m ake sure that you m ark “Simulativ e Cruise” as active.
18 Chapter4: Simple troubleshooting and maintenance. 4.1 Simple T roubles hooting T able: Failure Possible Cause Soluti ons Power connected b ut the camera i s not perfor ming self-test, no image Connected t he wrong power cord Check volt age in c able Power supply is damaged Check power r atings.
19 Blurry Image Manual focu s on the state Make sure s ettings are on auto focus. If so t ry t o shift the ca mera in any direction to reinst ate aut o focus mode Long delay s in actions performing / camera goin g out of contr ol. Power rating is not suf ficient Replace power supply to meet the requirement s of the power consumption.
An important point after buying a device Provision-ISR LC-10 IR (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Provision-ISR LC-10 IR yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Provision-ISR LC-10 IR - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Provision-ISR LC-10 IR you will learn all the available features of the product, as well as information on its operation. The information that you get Provision-ISR LC-10 IR will certainly help you make a decision on the purchase.
If you already are a holder of Provision-ISR LC-10 IR, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Provision-ISR LC-10 IR.
However, one of the most important roles played by the user manual is to help in solving problems with Provision-ISR LC-10 IR. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Provision-ISR LC-10 IR along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
