Instruction/ maintenance manual of the product 831.21941.2 ProForm
Go to page of 24
Model No. 831.21941.2 Serial No. Write the serial number in the space above for reference. Serial Number Decal (under frame) • Assembly • Operation • Maintenance • Part List and Drawing Sears, Roebuck and Co.
TABLE OF CONTENTS WARNING DECAL PLACEMENT ............................................................... 2 IMPORTANT PRECAUTIONS .................................................................. 3 BEFORE YOU BEGIN ...................................
iMPORTANT PRECAUTIONS 3.
BEFORE YOU BEGIN Thank you for selecting the new PROFORM '_' XP 210 U exercise bike. Cycling is an effective exercise for increasing cardiovascular fitness, building endurance, and toning the body. The XP 210 U exercise bike provides a selection of features designed to make your workouts at home more effective and enjoyable.
PART iDENTiFiCATiON CHART Use the drawings below to identify the small parts needed for assembly. The number in parentheses below each drawing is the key number of the part, from the PART LIST near the end of this manual. The number following the key number is the quantity needed for assembly.
ASSEMBLY Assembly requires two persons. Place all parts in a cleared area and remove the packing materials. Do not dispose of the packing materials until you complete all assembly steps.
, Orient the Upright (3) as shown. Have a second person hold the Upright near the Frame (1). Locate the wire tie in the lower end of the Upright (3). Tie the wire tie to the Main Wire (31). Then, pull the upper end of the wire tie until the Main Wire is routed through the Upright.
. Orient the Top Shield (9) as shown. Slide the Top Shield onto the Upright (3). Attach the Top Shield (9) to the Frame (1) with two M4 x 16mm Screws (40). Orient the Top Shield Cap (10) as shown. Press the Top Shield Cap onto the Left and Right Shields (17, 18).
. Loosen and remove the Seat Knob (11) from the Seat Carriage (30). Look underneath the Seat (12), and locate the Carriage Block (55) inside the Seat Carriage (30). Orient the Seat Post (5) as shown. Set the Seat Carriage (30) in the bracket on the Seat Post.
, Orient the Console Plate (19) and the Handlebar (47) as shown. Have a second person hold the Console Plate and the Handlebar near the Upright (3). Locate the Pulse Wire (52) in the Handlebar (47). Insert the Pulse Wire into the hole in the Upright (3), and then pull it upward out of the top of the Upright.
12. While a second person holds the Console (6) near the Console Plate (19), connect the wires on the Console to the Main Wire (31) and to the Pulse Wire (52). Insert the excess wire into the Console Plate (19) or into the Console (6). Tip: Avoid pinching the wires.
HOW TO USE THE EXERCISE BiKE HOW TO LEVEL THE EXERCISE BiKE If the exercise bike rocks slightly on your floor during use, turn one or both of the leveling feet on the rear stabilizer until the rocking motion is eliminated.
CONSOLE DIAGRAM RESISTANCE _mm | | [] mm_ TIME I SJ, LJ SPEED RESISTANCE FEATURES OF THE CONSOLE The advanced console offers an array of features designed to make your workouts more effective and enjoyable. When you use the manual mode of the console, you can change the resistance of the pedals with the touch of a button.
HOW TO USE THE MANUAL MODE 1. Turn on the console. Press any button or begin pedaling to turn on the console. When you turn on the console, the display will light. A tone will sound and the console will be ready for use. 2. Select the manual mode. When you turn on the con- sole, the manual mode will be selected automatically.
5. Measure your heart rate if desired. if there are sheets of plastic on the metal contacts on the handgrip heart rate monitor, remove the plastic, in addition, make sure that your hands are clean. To measure your heart rate, hold the handgrip heart rate monitor with your palms resting Contacts against the contacts.
HOW TO USE A PRESET WORKOUT 1. Turn on the console. Press any button or begin pedaling to turn on the console. When you turn on the console, the display will light. A tone will sound and the console will be ready for use. 2. Select a preset workout. To select a preset work- out, press the 7 Wt.
HOW TO USE AN IFIT WORKOUT iFit cards are available separately. To purchase iFit cards, go to www.iFit.com or call 1-888-533-1333. iFit cards are also available at select stores. 1. Turn on the console. Press any button or begin pedaling to turn on the console.
THE USER MODE The console features a user mode that allows you to select a unit of measurement for the console and to view console usage information. 1. Select the user mode. To select the user mode, press and hold down the Display Mode button for a few seconds until the user mode information appears in the display.
MAINTENANCE AND TROUBLESHOOTING Inspect and tighten all parts of the exercise bike regu- larly. Replace any worn parts immediately. To clean the exercise bike, use a damp cloth and a small amount of mild soap. IMPORTANT: To avoid damage to the console, keep liquids away from the console and keep the console out of direct sunlight.
HOW TO ADJUST THE DRIVE BELT if you can feel the pedals slip while you are pedaling, even when the resistance is adjusted to the highest level, the drive belt may need to be adjusted. To adjust the drive belt, you must remove the top shield cap, the top shield, and the right shield (see the instructions below).
EXERCISE GUiDELiNES These guidelines will help you to plan your exercise program. For detailed exercise information, obtain a reputable book or consult your physician.
PART LIST Model No. 831.21941.2 R0811B Key No. Qty. Description Key No. Qty. Description 1 1 Frame 30 1 Seat Carriage 2 1 Front Stabilizer 31 1 Main Wire 3 1 Upright 32 1 M10 Flange Nut 4 2 Stabilizer Cap 33 1 M10 x 50mm Screw 5 1 Seat Post 34 1 Resistance Cable 6 1 Console 35 3 M4.
EXPLODED DRAWING Model No. 831.21941.2 R0811B 40 6 8 . 40 41 18 40 52 5 31 16 43 23 51 49 44 13 19 40 44 45 36 15 38 23.
Your Home For repair--in your home--of all major brand appliances, lawn and garden equipment, or heating and cooling systems, no matter who made it, no matter who sold it! For the replacement parts, accessories, and user's manuals that you need to do-it-yourself.
An important point after buying a device ProForm 831.21941.2 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought ProForm 831.21941.2 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data ProForm 831.21941.2 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, ProForm 831.21941.2 you will learn all the available features of the product, as well as information on its operation. The information that you get ProForm 831.21941.2 will certainly help you make a decision on the purchase.
If you already are a holder of ProForm 831.21941.2, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime ProForm 831.21941.2.
However, one of the most important roles played by the user manual is to help in solving problems with ProForm 831.21941.2. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device ProForm 831.21941.2 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
