Instruction/ maintenance manual of the product 100SX Profile
Go to page of 20
100SX 200SX 400SX 600SX 800SX 1200SX 440SX 640SX MOSFET POWER AMPLIFIERS Installation Instructions / Owner's Man ual.
I NTRODUCTION Congratulations on your purchase of a California state-of-the-art power amplifier. Your selection of a California car audio product indicates a true appreciation of fine musical reproduction.
S AFETY PRECAUTIONS Fuse amplifier’s power wire at the battery . Be sure to fuse the power wire within 12” of the car's battery. This will protect the car's battery in case of a short circuit between the power amplifier and battery.
F EATURES AND BENEFITS DC Offset Protection This circuit protects the output of the amplifier against DC voltage. If for some reason DC voltage is detected at the output stage, the amplifier will shut down protecting the speakers from direct current.
Bass Boost For added low frequency performance the two channel amplifiers are equipped with 12dB bass boost. Power Fusing This protects the amplifier against short circuits and excessive current. Remote Turn-on Automatically turns amplifier on when connected to the head unit's remote output.
M OUNTING LOCATION Before you start the installation, it will be necessary to find a mounting location for the amplifier. Find a location in which the amplifier will receive adequate ventilation in order to dissipate the heat it develops during operation.
Connect the amplifier to the car's battery. At times, the amplifier will need to draw large levels of current that cannot be provided by any circuit in the car's fuse box. We recommended using an 8 to 10 gauge power wire for your connections depending on the amplifier and length of the wire.
7 INPUT CH1 CH2 CH4 CH3 X-OVER 40Hz 130Hz X-OVER 40Hz 130Hz BASS BOOST 0dB 12dB BASS BOOST 0dB 12dB FILTER LOW HI OFF FILTER LOW HI OFF MIN MIN MAX MAX LEVEL LEVEL 85Hz 85Hz R R Connect 2 sets of RCA .
8 If a low level RCA signal source is not available, you may still wire the models 100SX, 200SX, and 400SX with high-level or speaker level outputs from your head unit. However, only speaker leads from a "floating ground" system may be used (see diagram below).
B + REM GND FUSE L - R + R - L + BRIDGED L - R + R - L + BRIDGED CH1, 2 CH3, 4 Make the speaker connections using speaker wire that is at least 16 gauge or heavier. As with any audio component, proper phasing of the amplifier and speakers is essential for strong bass response.
B + REM GND FUSE L - R + R - L + BRIDGED L - R + R - L + BRIDGED CH1, 2 CH3, 4 + + - - + + - - 4 Ohm Speaker 4 Ohm Speaker 4 Ohm Speaker 4 Ohm Speaker L - R + R - B + REM GND FUSE L + BRIDGED + + - - .
CAUTION! In Tri- mode operation, the amplifier must see a 2 Ohm load or higher for the stereo satellites and no lower than 4 Ohms for the subwoofer(s). Any lower than the above mentioned impedance will cause the amplifier to overheat and possibly cause permanent damage to the amplifier.
MIN MAX LEVEL FIL TER X-OVER BASS BOOST 40Hz 130Hz 0dB 12dB LOW HI OFF Select your crossover type and frequency. . (Please note: If you intend to u se the amplifier in the Tri-mode configuration, it i.
T ROUBLE SHOOTING THE SYSTEM We have put together this trouble-shooting guide if you experience problems after installing the amplifier. Please keep in mind that the majority of problems incurred are caused by improper installation and not the equipment itself.
S PECIFICATIONS 100SX O u t p u t P o w e r @ 4 O h m..................................................2 x 7 0 W A T T S R M S ....................................................2 x 3 5 W A T T S R M S ................................................
15 600SX ....................................................2 x 1 5 0 W A T T S R M S ...................................................2 x 2 2 5 W A T T S B r i d g e d R M S @ 4 O h m..................................................1 x 4 5 0 W A T T S T H D @ R M S P o w e r .
440SX ....................................................4 x 5 0 W A T T S R M S ....................................................4 x 7 5 W A T T S B r i d g e d R M S @ 4 O h m..................................................2 x 1 5 0 W A T T S T H D @ R M S P o w e r .
LIMITED WARRANTY Profile Consumer Electronics, Inc. warrants this product to be free from defects in material and workmanship for a period of One (1) Year from the date of sale to the original consumer purchaser.
WARRANTY REPAIR POLICY In the unlikely event of product failure, the following procedures should be followed 1) The unit must be under the 1-year warranty period. 2) The unit must have no physical damage. 3) A copy of the original proof of purchase must be sent with the unit.
PROFILE CONSUMER ELECTRONICS, INC. 15060 SHOEMAKER AVE SANTA FE SPRINGS, CA 90670 TEL: (562) 404-9393 FAX: (562) 404-9433 WWW.PROFILEUSA.COM By.
An important point after buying a device Profile 100SX (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Profile 100SX yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Profile 100SX - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Profile 100SX you will learn all the available features of the product, as well as information on its operation. The information that you get Profile 100SX will certainly help you make a decision on the purchase.
If you already are a holder of Profile 100SX, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Profile 100SX.
However, one of the most important roles played by the user manual is to help in solving problems with Profile 100SX. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Profile 100SX along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
