Instruction/ maintenance manual of the product SN250TYLA-D Procom
Go to page of 21
COMP ACT LP .& NA TURAL GAS VENT -FREE STOVE OWNER ’ S OPERA TION AND INST ALLA TION MANUAL W ARNING: If the information in this manual is not followed exactly, a fire or explosion may re- sult causing property damage, personal injury, or loss of life.
2 IMPORT ANT : Read this owner’s manual carefully and completely before trying to assemble, operate, or service this heater. Improper use of this heater can cause serious injury or death from burns, fire, explosion, electrical shock, and carbon monoxide poisoning.
3 SAFETY INFORMA TION Continued 15. T urn off and unplug heater and let cool before servicing. Only a qualified service person should service and repair heater. 16. Operating heater above eleva- tions of 4,500 feet could cause pilot outage. 17. Do not operate heater if any log is broken.
4 AIR FOR COMBUSTION AND VENTILA TION W ARNING: This heater shall not be installed in a confined space or unusually tight construc- tion unless provisions are provided for adequate combustion and ven- tilation air. Read the following in- structions to insure proper fresh air for this and other fuel-burning appliances in your home.
5 W ARNING: Rework worksheet, adding the space of the adjoining unconfined space. The combined spaces must have enough fresh air to supply all appliances in both spaces. If the actual Btu/Hr used is less than the maximum Btu/Hr the space can support, the space is an unconfined space.
6 NOTICE: This heater is in- tended for use as supplemental heat. Use this heater along with your primary heating system. Do not install this heater as your primary heat source. If you have a central heating system, you may run system's circulating blower while using heater .
7 CONNECTING TO GAS SUPPL Y W ARNING: A qualified service person must connect heater to gas supply. Follow all local codes. CAUTION: Never connect heater directly to the gas supply . This heater requires an external regulator (not supplied). lnstall the external regulator between the heater and gas supply.
8 W ARNING: T est all gas piping and connections for leaks after install- ing or servicing. Correct all leaks at once. W ARNING: Never use an open flame to check for a leak. Apply a mixture of liquid soap and water to all joints. Bubbles forming show a leak.
9 W ARNING: Failure to position the parts in accordance with these diagrams may result in property dam- age or personal injury. CAUTION: After installation and periodically thereafter, check to ensure that no flame comes in contact with any log. With the heater set to HIGH, check to see if flames contact any log.
1 0 THERMOST A T CONTROL OPERA TION The thermostat control knob can be set to any comfort level between HI and LO. The thermostat will gradually modulate the heat output and flame height from higher to lower settings, or pilot, in order to maintain the comfort level you select.
1 1 CLEANING ODS/IGNITOR AND BURNER Clean with a vacuum cleaner. CLEANING MAIN AIR INLET HOLE We recommend that you clean the unit every three months or after 2500 hours of operation. We also recom- mend that you keep the burner tube and pilot assembly clean and free of dust and dirt.
1 2 REMEDY TROUBLESHOOTING Note : All troubleshooting items are listed in order of operation. W ARNING: T urn off heater and let cool before servicing. Only a qualified service person should service and repair heater. CAUTION: Never use a wire, needle, or similar object to clean ODS/pilot.
1 3 TROUBLESHOOTING Continued OBSERVED PROBLEM POSS IBLE CAUSE REMEDY Delayed ignition burner. 1. Manifold pressure is too low. 2. Burner orifice is clogged. 1 . Contact local gas company. 2. Clean burner (see Cleaning and Maintenance, pages 1 1). Burner backfiring during combustion.
1 4 REPLACEMENT P ARTS Note : Use only original replacement parts. This will protect your warranty coverage for parts replaced under warranty. P ARTS UNDER W ARRANTY Contact authorized dealers of this product. If they can't supply original replacement part(s) call the number on the back of manual.
1 5 1. Install legs and flex tube. Lay the heater down on its back and remove the regulator dustproof sticker and assemble the gas line into the inlet hole on the regulator. 2. Install the decorating logs. Fasten decorating logs 1 ¡¢ ¡¢ ¡¢ ¡¢ ¡¢ 2 ¡¢ ¡¢ ¡¢ ¡¢ ¡¢ 3 onto the correspon dent angle iron (Figur e 3).
1 6 ILLUSTRA TED P ARTS BREAKDOWN SN250TYLA-D SL250TYLA-D.
1 7 P ARTS LIST SN250TYLA-D SL250TYLA-D This list contains replaceable parts used in your heater. When ordering parts, follow the instructions listed under Replacement Parts on page 14 of this manual .
1 8 ILLUSTRA TED P ARTS BREAKDOWN SN250TYLA-D SL250TYLA-D 20.
1 9 P ARTS LIST SN250TYLA-D SL250TYLA-D O N Y E K T R A P R E B M U N N O I T P I R C S E D Y T Q D - A L Y T 0 5 2 N SD - A L Y T 0 5 2 L S 10 0 0 3 3 B Ey l b m e s s A s g o L g n i t a r o c e D1 .
2 0 INST ALLING BLOWER ACCESSOR Y BLOWER ACCESSOR Y MODEL NFHTX186 1 . From back of heater remove the knock-out center panel with two brackets at the four sides with a Philips head screwdriver (see Figure 1). 2 . Attach the two brackets to blower housing using four white screws provided in blower kit (2 for each bracket) (see Figure 3).
2 1 INST ALLING BLOWER ACCESSORY BLOWER ACCESSOR Y MODEL NFHTX186 Figure 4-A Routing Power Cord Figure 4-B Routing Power Cord Wiring Diagram Decal Figure 5 Mounting Control Housing SIDE VIEW.
An important point after buying a device Procom SN250TYLA-D (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Procom SN250TYLA-D yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Procom SN250TYLA-D - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Procom SN250TYLA-D you will learn all the available features of the product, as well as information on its operation. The information that you get Procom SN250TYLA-D will certainly help you make a decision on the purchase.
If you already are a holder of Procom SN250TYLA-D, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Procom SN250TYLA-D.
However, one of the most important roles played by the user manual is to help in solving problems with Procom SN250TYLA-D. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Procom SN250TYLA-D along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
