Instruction/ maintenance manual of the product DX850 Primera Technology
Go to page of 16
Quick S tart © 2009 All rights reserved Unpacking and Setup 3 Loading the Label S tock 4 Dispensing the Label 9 Using the Control Panel 1 1 Label Path Diagram 12 T roubleshooting and Maintenance 13 S.
Notices : The information in this document is subject to change without notice. NO W ARRANTY OF ANY KIND IS MADE WITH REGARD TO THIS MA TERIAL, INCL UDING, BUT NOT LIMITED TO , THE IMPLIED W ARRANTIES OF MERCHANT ABILITY AND FITNESS FOR A P ARTICULAR PURPOSE.
Thank you for purchasing the DX850 Label Dispenser (hereafter referred to as "Label Dispenser"). The Label Dispenser includes a P ower Cord, 12 volt P ower A dapter and the parts shown in F igure 1-1. The Roll Bar , Roll Guides and Roll Drag Ar m are located in the supply box along with the P ower Cord.
1. Remove the Roll Bar and Roll Guides from the Label Dispenser . The Roll Guides and Roll Drag Arm are removable and adjustable. They are held in place magnetically . (Figure 2-1.) 2. Remove one Roll Guide and the Roll Drag Arm from the Roll Bar . 3.
4. Place the Roll Drag Arm under the Roll Bar . The Roll Drag Arm may be placed on either side of the Roll Bar , but the rounded tip of the Roll Drag Ar m should be located in the center of the inside of the core. The arm is spring loaded so that there is downward pressure on the inside of the roll.
6. Now position the stock to correspond with the general area where the labels will be dispensed. 7. Pull the loose end of the label stock forward under the T op Roller . Pull appro ximately 6 inches of label stock out beyond the P eel Edge. (F igure 2-5.
9. Pull the stock through until the P eel Edge is positioned in between two of the labels. (F igure 2-7.) Note: The liner may be fed out the front or back of the Label Dispenser . 10. P ush the Liner Idler Roller into the clamped position by pressing your thumbs on the Liner Idler Roller T abs on both sides.
11. Move the Label Sensor Bracket where desired within the width of the label. (F igure 2-9.) 12. Y ou are now ready to dispense labels. 8 DX850 Label Dispenser F igure 2-9.
DX850 Label Dispenser 9 T o dispense a label, first load label stock as described in Section 2, connect power and switch on the Label Dispenser . F ollow these steps to dispense labels.
10 DX850 Label Dispenser 3. A label will peel off the liner until it trips the Label Sensor . (F igure 3-3.) 4. Pull the label off the liner with a quick upward motion.
DX850 Label Dispenser 11 The Control P anel can be used to start and stop dispensing of labels, display label counts and other advanced functions. Start/Stop Button: Starts or stops the motor depending on whether or not the label sensor is tripped. Note: If sensor does not get triggered in a 24” run, the motor will stop.
12 DX850 Label Dispenser Section 5: Label P ath Diagram Label Path Peel Edge Liner Drive Roller Liner Idler Roller Label Path Diagram Front or Rear Liner Output.
DX850 Label Dispenser 13 T roubleshooting Motor stalling on labels 6" (152 mm) or wider . F or label stock 6” (152 mm) and wider , it may be necessar y to reduce the speed of the Label Dispenser . The Label Dispenser includes a Half-Speed Mode that generates more power from the motor for wider label stock.
Supply roll diameter: Up to 8" (203mm) Label width: 0.75" to 8.25" (19.1mm to 209.6mm) Media liner width: 1.00" to 8.38" (25.4mm to 213.0mm) Label height/length: 0.75" to 24.00" (19.1mm to 609.6mm) Supply roll core: 2" to 3" (51.
.
P/N 511260 - 052609.
An important point after buying a device Primera Technology DX850 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Primera Technology DX850 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Primera Technology DX850 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Primera Technology DX850 you will learn all the available features of the product, as well as information on its operation. The information that you get Primera Technology DX850 will certainly help you make a decision on the purchase.
If you already are a holder of Primera Technology DX850, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Primera Technology DX850.
However, one of the most important roles played by the user manual is to help in solving problems with Primera Technology DX850. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Primera Technology DX850 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
