Instruction/ maintenance manual of the product EFX 821 Precor
Go to page of 48
As sembling and Maintaining the EFX® 821 Elliptical Fitnes s Cr os s tr ainer ™ Prec or Incorporated 20031 142nd A venue NE P .O . Box 7 202 W oodinville, W A USA 98072-400 2 EFX 821 P AG/ OM 3007 .
.
As sembling and Maintaining the EFX ‰ 821 Elliptical Fitnes s Cr oss tr ainer ™.
Edition Inf ormation ASSEMBLING AND MAINTAINING THE EFX 821 ELLIPTIC AL FITNESS CROSSTRAINER P/N 300763-101 rev A Copyright ©2011 Precor Incorporated. All rights reserved. Specifications subject to change wi thout notice. Trademark Note Precor, AMT, and E FX are registered tr ademarks and Preva is a trademark of Precor Incorporated.
Chapter 1 Important Safe ty Instructions Read the following precautions thoroughly before you begin assembly, and save them afterward for future reference. Safety Precautions Always follow basic safety precautions when using this equipment to reduce the chance of injury, fire, or damage.
4 Assembling and Maintaining the EFX 821 Elliptical Fitness Crosstrain er Never leave the equipment unattended when it is plu gged in. Unplug the equipment from its power source wh en it is not in use, before cleaning it, and before providing authorized service.
Important Safety Instructions 5 Maintain the equipment to keep it in good working condition, as described in the Maintenance section o f the assembly and maintenanc e guide. Inspect the equipment for incorrect, worn, or loose components, and then correct, replace or tighten prior to use .
6 Assembling and Maintaining the EFX 821 Elliptical Fitness Crosstrain er Educating Users Take time to educate users about the Important S afety Instructions found in both the User Reference Manual and Product Owner’s Manual .
Important Safety Instructions 7 Regulatory Notices for Cardiovascular Exercise Equipment The regulatory information in this section applies to the exercise equipment and its control console. Safety Approvals for Cardiovascular Equipment Precor equipment has been tested and found to comply with the following applicable safety st andards.
8 Assembling and Maintaining the EFX 821 Elliptical Fitness Crosstrainer Industry Canada This Class A digital ap paratus complies with Can adian ICES-003.
Important Safety Instructions 9 The grounding plug on a treadmill or power supply lo oks like the plug shown in one of the following two figures. The po wer outlet must have the same configuration as the plug. Important: Do not use any power cord adapter with this product.
10 Assembling and Maintaining the EFX 821 Elliptical Fitness Crosstrain er.
T able of C ont ents Important Safety Instructions .................................................... 3 Safety Prec autions ................................................................................ 3 Educating Users ..........................
.
Chapter 2 As sembling the EFX WARNING You will need the assistance of two other people to assemble this unit. DO NOT attempt assembly by yourself . Important : The instructions in the following proced.
14 Assembling and Maintaining the EFX 821 Elliptical Fitness Crosstrain er Begin installation of all fasteners by hand, then partially tighten them. Do not fully tighten faste ners until instructed to do so. Important : When wrench-tightening the screws, make sure the head of the fastener is paralle l to the product surface.
Assembling the EFX 15 Required Tools Wire tie cutter Phillips-head screwdriver Two ⁹⁄₁₆ -inch combination wrenches (open-end and box) SAE Standard socke t set Hardware Kit (not to scale) Table 1.
16 Assembling and Maintaining the EFX 821 Elliptical Fitness Crosstrain er Fasteners Quantity Bushings 2 Link arm caps 2 Pivot arm caps 2 Pivot axle covers 2 Upright support covers (packaged separatel.
Assembling the EFX 17 Assembling the EFX Assemble the EFX in the order presented. Once you have assembled it, clean the ramp with a soft cloth dampened in a diluted solution of mild soap and water. To begin assembl y: 1. Feed the cable through the right upright suppor t.
18 Assembling and Maintaining the EFX 821 Elliptical Fitness Crosstrainer 2. Attach both upright suppo rts to the base frame using eight buttonhead screws, eigh t split washers, and eight washers. Finger tighten. Figure 4: Attaching the upright supports Installing the Display Console Mount 1.
Assembling the EFX 19 3. Fasten the display console m ount to each upright support by threading a buttonhead screw, washer, and split washer through opposite m ounting holes. Check that the base fasteners are loose before installi ng the display console fasteners.
20 Assembling and Maintaining the EFX 821 Elliptical Fitness Crosstrain er Installing the Bottle Holder The bottle holder attaches to the right stationary arm handrail. To install the bottle holder: 1. Position the water bottle holder as shown an d attach it to the right stationary handrail.
Assembling the EFX 21 Installing the Handlebars CAUTION: Handlebars can s wing and cause injury. Have your assistant hold the ha ndlebar and gently lo wer it into a vertical position when the handleb ar assembly is complete. To install the moving handlebars: 1.
22 Assembling and Maintaining the EFX 821 Elliptical Fitness Crosstrain er 3. Attach the handlebars to the link arms using two hex head screws, two bushings, and four washers. For ease of installation, slide the corresponding foot pedal to the top of the ramp before attaching each handlebar.
Assembling the EFX 23 Attaching the Caps an d Upright Support Cover You will need the arm caps and foot covers to complete the following tasks. To attach the caps and u pright support covers: 1. Align the cut-out inside the link arm cap with the link arm mounting hole.
24 Assembling and Maintaining the EFX 821 Elliptical Fitness Crosstrain er 4. Slide the covers down into the base mount. Secure each pair of covers using two self-tapping screws and a Phillips-head screwdriver. Figure 13: Attaching the pivot axle covers 5.
Assembling the EFX 25 Verifying that the Heart Ra te Display is Operational To verify that the heart rate display is operational: 1. Hold on to a stationary handrail and step on the foot pedals. 2. When you are comfortably si tuated, begin pedaling. A pedaling speed above 40 strides per minute must be maintained for several seconds.
.
Chapter 3 Ins talling the Console To make installation easier, all Precor Experience Series consoles use the same mounting hardware and connector locations whenever possible.
28 Assembling and Maintaining the EFX 821 Elliptical Fitness Crosstrainer Threading the Cable Assembly Earlier in the installation, you threaded the necessary cables through the frame of the base unit and out the passthrough opening in the console mount.
Installing the Console 29 Connecting Cables After the console has been seated, separate the individual cables out of the end of the cable asse mbly and attach them to the appropriate circuit connectors inside the console. Refer to the following diagram and table to id entify the cables and connectors.
30 Assembling and Maintaining the EFX 821 Elliptical Fitness Cros strainer Completing the Console Installation Before you complete the final installation steps, double-check the connections you have made. Make sure that all cables are fully and securely connected, and that any unneeded cables are tied back properly.
Chapter 4 Self-Po w er ed Featur es On self-powered equipment, the system initializes and displays the Welcome screen when a user starts exe rcising. A minimum rate of motion must be maintained for the banner to appear, as shown in the following table.
32 Assembling and Maintaining the EFX 821 Elliptical Fitness Cros strainer Informational Displays Prior to Shutdown The equipment saves its battery charge by moving into a shutdown mode. If the user does not maintain the minimum rate of motion, a 30-second shutdown process begins.
Self-Powered Features 33 Using the Optional Power Adapter After connecting the power adap ter to the equipment, plug the opposite end into the appropriate power source (120 V or 240 V). CAUTION: When the optional powe r adapter is in use, make sure that the power supply cord does not create a safety hazard.
34 Assembling and Maintaining the EFX 821 Elliptical Fitness Cros strainer Replacing the Battery The equipment’s battery is built to last for a long time. However, if you feel that the battery may need replacing, check with an authorized service technician.
Chapter 5 Maint enanc e To keep the equipment functioning properly, perform the minor maintenance tasks in this section at the intervals shown on the maintenance checklis t. Failure to maintain the equipment as described in this section could void the Precor Limited Warranty.
36 Assembling and Maintaining the EFX 821 Elliptical Fitness Crosstrainer CAUTION: Read and follow the manufacturer’s instructions, particularly dilut ion instructions, before using any clean er on Precor fitness equipmen t.
Maintenance 37 7. Verify that th e unit sits squarely on the floor. All of its feet should be touching the floor and the unit should not rock or wobble when in use. If not, re-level it as described in. Monthly Maintenance DANGER USE EXTREME CAUTION when the rear cover of any EFX is removed.
38 Assembling and Maintaining the EFX 821 Elliptical Fitness Crosstrain er Storing the Chest Strap If you purchased the optional heart rate chest strap, store it in a place where it remains free of du st and dirt (for example, in a closet or drawer). Be sure to protect the chest strap from extremes in temperature.
Chapter 6 C ommer cial Car dio v a scular Equipment Limit ed W arr anty PLEASE READ THESE WARRANTY TERMS AND CONDITIONS CARE FULLY BEFORE USING YOUR PRECOR INCORPORATED PROD UCT. BY USING THE EQUIPMENT, YOU ARE CONSENTING TO BE BOUND BY THE FOLLOWING W ARRANTY TERMS AND CONDITIONS.
40 Assembling and Maintaining the EFX 821 Elliptical Fitness Crosstrain er Options / Accessories Many options or accessories have components that are connected internally or mounted inside the electronic console. The following guidelines deter mine the warranty for these components.
Commercial Cardiovascular Equipment Limited Warranty 41 This Limited Warranty sha ll not apply to: 1. Software version upgrades. 2. Software defects that do not materially an d negatively affect the normal performance of the product under norma l conditions of use.
42 Assembling and Maintaining the EFX 821 Elliptical Fitness Crosstrainer EXCLUSION OF CONSEQUENTIAL AND INCIDENTAL DAMAGES. PRECOR AND/OR ITS SUPPLIERS SHALL HA VE NO OBLIGATION OR LIABILITY, WHETHER.
Notes 43.
44 Assembling and Maintaining the EFX 821 Elliptical Fitness Crosstrain er.
.
As sembling and Maintaining the EFX® 821 Prec or Incorporated 20031 142nd A venue NE P .O . Box 7 202 W oodinville, W A USA 98072-400 2 EFX 821 P AG/ OM 3007 63- 101 rev A 13 January 2011.
An important point after buying a device Precor EFX 821 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Precor EFX 821 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Precor EFX 821 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Precor EFX 821 you will learn all the available features of the product, as well as information on its operation. The information that you get Precor EFX 821 will certainly help you make a decision on the purchase.
If you already are a holder of Precor EFX 821, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Precor EFX 821.
However, one of the most important roles played by the user manual is to help in solving problems with Precor EFX 821. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Precor EFX 821 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
