Instruction/ maintenance manual of the product PADVD-220T Power Acoustik
Go to page of 24
P AD VD -220/ P AD VD -220T Single-DIN A/V Multimedia Source Touch Sensor DVD/CD/MP3/MP4 AM/FM Radio Built-in TV tuner Owner’s Manual Take the time to read thro ugh this ow ner’s manual. Familiarity with installation and operation pr ocedures will hel p you obtain the best Performance from your new DVD-receiver.
Page- 1 Table of Contents Table of Contents..... ............................ .................... ......................... ..................... ........... ......... 1 Important Safeguards ............. ............. ............. .................
Page -2 Important Safeguards z Using the device at temperature below -10 may cause the breakage of the device. BEFORE ℃ USING PLEASE HEAT UP TH E PASSENGER COMPARTMENT TO THE RECOMMENDED TEMPERATURE! z Read carefully through t his manual to familiariz e yourself with this high-quality sound system.
Page- 3 Accessories Package contains the following accessories for instal lation and operation of the unit. (1) W asher , S pring W asher , M5 Nut 1 each (2) Mounting S trap 1 (3) Screw (4) Bolt 1 4 (.
Page -4 Installation/Un-Installation First complete the electric al connections, and then check them for correctness. Installation This unit can be installed in any dashboard hav ing an opening as shown on the picture. The dashboard should be 4.75 – 5.
Page- 5 Wiring Connections Make sure you have good chassis ground. A good ground connection will eliminate most electrical noise problems. A good chassis ground requires a tight connection to the vehicle’s metal chassis.
Page -6 Caution: Do not interch ange the connection of the wiring!!! For some car models you may need to modify wiring of the supplied power cord. Contact your authorized car dealer before installing this unit.
Page- 7 Panel Controls 1. Power/Mute 2. BAND 3. PREVIOUS 4. VOL + 5. NEXT 6. DISP 7. AS/PS 8. LCD 9. IR sensor 10. OPEN 11.MODE. 12.OK 13.VOL- 14. PRESET 1/play pause 15. PRESET 2./RPT 16. PRESET 3./INT 17. PRESET 4/RDM 18. PRESET 5/STOP 19. PRESET 6/MENU 20.
Page -8 IR Remote Control REPLACIN G THE BATTERY Remote Control comes with a CR-2025 Lithium Battery included. 1. Remove the Batter y Holder from the back of the Remote Control. 2. Insert a CR-2025 Lithium battery with the positive (+) mark upward. Insert the Battery Holder into the back of the Remote Control.
Page- 9 General Ope rations Reset the Unit In case the unit is malfunctioned or need to reset to factory default setting, press RESET button in inner p anel then the unit will be reset. Power on/of f Press POWER key button to turn on the unit. Long press POWER key on front panel or press PO WER button on RC to power off the unit.
Page -10 Digital Tuner Band selection Press MODE button to select the RADIO mode. Press the BAND button to select the desired band: FM1=> FM2 => FM3 => AM1=>AM2 STEREO/MONO In FM mode, press SETREO /MONO button on remote control to select stereo or mono sound reception.
Page- 1 1 SD/MMC Cards & USB Operations USB Flas h Memory To play MP3/ MP4/ WMA files from a USB flash memory, insert a USB flash memory into the US B port on the right side of the unit. The unit will start playing MP3/MP4/ WMA files on the USB flash memory automatically.
Page -12 Repeat Press the RPT button on remote control or the panel for RPT1 (repeat the current playing file) => RPT ALL (repeat all folders) => RPT folder (repeat curr ent folder) => RPT OFF. Repeat A-B Functi on 1. Press A-B button on the r emote at the starting point of the section you want to repeat (point A).
Page- 13 Discs operations Glossary PBC (Play Back Control) Play Back Control is a menu recorded on the disc with SVCD or VCD2.0 format. For the discs contained PBC, it can playback interactive software with the menu displayed on TV . And if the disc contains still images, it can playback high definition of still image.
Page -14 Playing/pausing To ensure good system performance, wait until the unit finishes reading the disc informat ion before proceeding. Press the PLAY/ PAUSE button to start/ pause the playback. In pause mode press it again to resume the playback. Stop During playback press the STOP button on the RC or on the panel.
Page- 15 PBC (Playback Co ntrol) function (for VCD only) If you insert a VCD with PBC, playback sta rts fr om the beginning of the 1st track automatically. 1. Long press PBC/STOP button to activate interactive menu on screen during playback. 2. If the menu consists of titles, you can select a desired one using the digit 0-9 buttons.
Page -16 MP3 overview Notes on MP3: z MP3 is short for MPEG Audio Layer 3 and refers to an audio compression technology standard. z This product allows playback of MP3 files on CD-ROM, CD-R or CD-RW discs. z The unit can read MP3 files written in the format compliant with ISO 9660.
Page- 17 Setup Menu • Press SETUP button to enter the system settings main menu; • Press cursor / buttons to move along icons on the t op navigation bar on settings main menu.
Page -18 Dolby settings Menu entry Dual mono With this menu item you can select the type of Left and Right channel audio output. Stereo is normal Stereo, Mono L is all sound on the Left Audio output, Mono R is all sound on the Right channel. The “Mix Mono” function only works when a DVD is being played in DTS 5.
Page- 19 Menu entry Function TV T ype This setting enables the selection of the appropriate TV standard. P A L is the customary standard in Europe. NTSC is the customary st andard in the US and Japan. Onl y select the MUL TI option if your TV can play back both formats.
Page -20 TV OPERA TIONS (TV function is for P ADVD-220T only) Connect TV antenna as it is shown on electrical connection diagram. Switch to TV mode Press MODE button repeatedly to select the TV mode, and press BAND select TV sy stem: P A L DK → PA L I → PA L B G → PA L M → PA L N → SCEAM DK → SCEAM BG → NTSC M Auto tuning 1.
Page- 21 Note on Discs Only use groundless loudspeakers. Use only loudspeakers of minimal 40 W att, using fewer watt s may result in damaging your loud speakers at higher volumes. Use 4~8 Ω (Ohm impedance) loudspeakers only; using higher or lesser impedance may damage the unit.
Page -22 T roubleshooting guide Symptom Cause Solution General No power The car ignition is not on. The fuse is blown. If the power supply is properly connected to the car accessory switch the ignition key to “ACC”. Replace the fuse. Disc Disc cannot be loaded.
Page- 23 Specification General Power supply: 12 V DC Current consumption: max. 10 A Maximum power output: 40W x 4 channels Compatible forma ts: DVD/SVCD/VC D/HD CD/M P3/MP4/WMA/CDDA/Picture-CD/JP EG/ CD-R/ -RW/DVD±R/± RW playback Dimensions (W x D x H) / weight: 178 x 175 x 50 mm / 1.
An important point after buying a device Power Acoustik PADVD-220T (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Power Acoustik PADVD-220T yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Power Acoustik PADVD-220T - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Power Acoustik PADVD-220T you will learn all the available features of the product, as well as information on its operation. The information that you get Power Acoustik PADVD-220T will certainly help you make a decision on the purchase.
If you already are a holder of Power Acoustik PADVD-220T, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Power Acoustik PADVD-220T.
However, one of the most important roles played by the user manual is to help in solving problems with Power Acoustik PADVD-220T. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Power Acoustik PADVD-220T along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
