Instruction/ maintenance manual of the product XT24H48YT Poulan
Go to page of 32
OPERA T OR'S MANU AL MODEL: XT24H48YT LA WN TRA CT OR AL W A YS WEAR EYE PR O TECTION DURING OPERA TION Visit our website: www .poulan-pro.com W ARNING: Read this Man u al and f ollow all W arnings and Saf ety Instructions. F ail ure to do so can re sult in serious in ju ry .
2 I. GENERAL OPERA TION • Read, understand, and f ollow all instructions on the machine and in the manual bef ore star ting. • Do not put hands or f eet near rotating par ts or under the machine.
3 • Be sure the area is clear of bystanders bef ore operat- ing. Stop machine if anyone enters the area. • Ne v er carry passengers. • Do not mow in re v erse unless absolutely necessary . Al ways look do wn and behind bef ore and while bac k- ing.
4 PR ODUCT SPECIFICA TIONS Gasoline Capacity 4.0 Gallons and T ype: Unleaded Regular Oil T ype (API-SG-SL): SAE 30 (abov e 32°F) SAE 5W-30 (belo w 32°F) Oil Capacity: W/Filter : 4.0 Pints W/O Filter: 3.75 Pints Spark Plug: Champion QC12YC (Gap: .040") Ground Speed (MPH): F orward: 5.
5 UNASSEMBLED P AR TS Steering Wheel Steering Wheel Insert (1) Large Flat Washer Steering Wheel Adapter Seat (2) Keys Slope Sheet Key (1) Oil Drain Tube (1) Knob (1) Washer 17/32 x 1-3/16 x 12 Gauge (4) Washers 3/8 x 3/4 x 14 Ga.
6 ASSEMBL Y T OOLS REQUIRED FOR ASSEMBL Y A sock et wrench set will mak e assemb ly easier . Stan dard wrench sizes are listed. (1) 3/4" wrench Pliers (1) 9/16" wrench Tire pressure gauge Ut.
7 ASSEMBL Y NO TE: Y ou ma y no w roll or drive y our tractor off the skid. F ollow the ap pro pri ate instruction below to remo v e the tractor from the skid . T O ROLL TRA CT OR OFF SKID (See Op- er a tion section for location and function of con tr ols) • Press lift lev er plunger and r aise attachment lift le v er to its highest po si tion.
8 ASSEMBL Y 02510 ANTI-SW A Y BAR SINGLE LOOP RET AINER SPRINGS GA UGE WHEEL SUSPENSION ARMS DOUBLE LOOP RET AINER SPRING FRONT SUS PEN SION BRA CKETS FRONT PLA TE AS SEM BL Y CHASSIS BRA CKET DOUBLE .
9 CHECK TIRE PRESSURE The tires on your tr actor were o v erinfl ated at the f actory f or shipping pur poses. Correct tire pressure is impor tant f or best cutting perf ormance. • Reduce tire pressure to PSI shown in “PR ODUCT SPEC I FI CA TIONS” section of this manual.
10 OPERA TION These symbols ma y appear on your tr actor or in literature supplied with the product. Learn and understand their mean- ing. DANGER, KEEP HANDS AND FEET AWAY FREE WHEEL (Automatic Models.
11 2854 OPERA TION KNO W Y OUR TRA CT OR READ THIS O WNER'S MANU AL AND SAFETY R ULES BEFORE OPERA TING Y OUR TRA CT OR Compare the illustrations with y our tractor to f amiliarize y ourself with the locations of v arious controls and ad just ments .
12 OPERA TION The operation of any tractor can result in f oreign objects thr own into the e yes, which can result in severe e ye dam age. Al wa ys wear safety glass es or eye shields while op- erating your tractor or per fo r m ing any adjustments or repair s.
13 T O ADJUST GA UGE WHEELS (See Fig. 8) Gauge wheels are properly adjusted when they are slightly off the ground when mow er is at the desired cutting height in operating position. Gauge wheels then keep the dec k in proper position to help pre v ent scalping in most terrain conditions.
14 ADD GASOLINE • Fill fuel tank to bottom of fi ller neck. Do not ov erfi ll. Use fresh, clean, regular un lead ed gasoline with a minimum of 87 octane. (Use of leaded gasoline will increase carbon and lead o xide deposits and reduce v alv e lif e).
15 FIG. 11 MO WING TIPS • Mow er should be proper ly le v eled f or best mowing per- f ormance. See “T O LEVEL MOWER HOUSING” in the Ser vice and Adjustments section of this manual. • The left hand side of mower should be used f or trim- ming.
16 MAINTENANCE LUBRICA TION CHART 02500 ➀ FRONT WHEEL BEARING ZERK ➀ FRONT WHEEL BEARING ZERK ➁ ENGINE ➀ SPINDLE ZERK ➀ SPINDLE ZERK ➀ GENERAL PURPOSE GREASE ➁ REFER T O MAINTENANCE “ENGINE” SECTION IMPORT ANT: DO NO T OIL OR GREASE THE PIVO T POINTS WHICH HA VE SPECIAL NYLON BEARINGS.
17 MAINTENANCE FIG. 12 TRA CT OR Alwa ys observe saf ety rules when per fo r m ing any main- te nance. BRAKE OPERA TION If tractor requires more than fi v e (5) f eet to stop at highest speed in high est gear on a le v el, dry concrete or paved surf ace, then br ake m ust be chec ked and ad just ed.
18 MAINTENANCE V- B E LT S Check V -belts f or deterioration and wear after 100 hours of operation and replace if necessary . The belts are not ad just able . Re place belts if the y begin to slip from wear . TRANSAXLE COOLING The transmission f an and cooling fi ns should be kept clean to assure proper cooling.
19 • Unlock drain v alv e b y pushing inward and turning coun ter clock wise. • T o open, pull out on the drain valv e . • After oil has drained completely , close and lock the drain v alv e b y pushing inward and turning clockwise until the pin is in the lock ed position as sho wn.
20 SER VICE AND ADJUSTMENTS FIG. 17 TRA CT OR W ARNING: T O A V OID SERIOUS INJUR Y , BEFORE PERFORMING ANY SER VICE OR AD JUST - MENTS: • Depress c lutch/brake pedal fully and set parking brake. • Place motion contr ol lever in neutral (N) position.
21 SER VICE AND ADJUSTMENTS • P osition front plate assembly between front mower brac kets . Raise deck and plate assemb ly to align holes and inser t fl anged pins . Secure pins with double loop retainer springs between the plate assembly and mo wer brac k ets.
22 SER VICE AND ADJUSTMENTS 02517 BO TH FRONT PLA TE LINKS MUST BE EQU AL IN LENGTH TRUN NION FRONT PLA TE AS- SEM BL Y NUT “C” NUT “D” FIG. 21 025 16 02513 FIG. 22 PRI MA RY IDLER ARM R.H. MANDREL IDLER PUL LEYS ELEC TRIC CLUTCH PUL LEY T O REPLACE MO WER DRIVE BEL T MO WER DRIVE BEL T REMO V AL (See Fig.
23 SER VICE AND ADJUSTMENTS 02515 L.H. MAN- DREL IDLER PUL LEY CEN TER MAN DREL SPRING SEC OND AR Y IDLER ARM SEC OND AR Y SPRING ARM R.H. MAN DREL T O REPLACE MO WER BLADE (SEC OND AR Y) DRIVE BEL T (See Fig. 23) P ark the tractor on le v el surf ace .
24 TRANSAXLE MO TION CONTROL LE VER NEUTRAL ADJUSTMENT (See Fig. 26) The motion control le v er has been pre set at the factory and adjustment should not be necessar y . • Loosen adjustment bolt in front of the right rear wheel, and lightly tighten.
25 FIG. 28 SER VICE AND ADJUSTMENTS T O REMO VE WHEEL FOR REP AIRS (See Fig. 27) • Block up axle securely . • Remove axle co v er , retaining r ing and washers to allow wheel remov al (rear wheel contains a square k e y - Do not lose). • Repair tire and reassemble .
26 SER VICE AND ADJUSTMENTS T O REMO VE HOOD AND GRILL ASSEMBL Y (See Fig. 30) • Raise hood. • Unsnap headlight wire connector . • Stand in front of tractor . Gr asp hood at sides, tilt to ward engine and lift off of tractor . • T o replace, re v erse abov e procedure .
27 ST ORA GE Immediately prepare your tr actor f or storage at the end of the season or if the tractor will not be used f or 30 da ys or more. W ARNING: Never store the trac tor with gas o line in the tank inside a building where fumes may reac h an open fl ame or spark.
28 TR OUBLESHOO TING POINTS Will not start 1. Out of fuel. 1. Fill fuel tank. 2. Engine not “CHOKED” properly . 2. See “T O ST ART ENGINE” in Operation section. 3. Engine fl ooded. 3. Wait se v eral min utes bef ore attempting to star t. 4. Bad spark plug.
29 TR OUBLESHOO TING POINTS Engine dies when 1. Rev erse operation system 1. T ur n ignition key to tractor is shifted (ROS) is not "ON" while ROS "ON" position. into reverse mow er or other attachment See Operation section. is engaged.
30 LIMITED W ARRANTY The Manuf acturer warr ants to the original consumer purchaser that this product as manuf actured is free from def ects in materi- als and work man ship.
31 15 DEGREES MAX. FOLD ALONG DO TTED LINE THIS IS A 15 DEGREE SLOPE ONLY RIDE UP AND DOWN HILL, NOT ACROSS HILL SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION WARNING: To avoid serious injury, operate your tractor up and down the face of slopes, never across the face.
This product has been exper tly en gi neered and carefully manu fa c tured to rigid quality stan dards. As with all mechanical products, some adjustments or par t replacement ma y be necessary dur ing the life of y our unit.
An important point after buying a device Poulan XT24H48YT (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Poulan XT24H48YT yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Poulan XT24H48YT - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Poulan XT24H48YT you will learn all the available features of the product, as well as information on its operation. The information that you get Poulan XT24H48YT will certainly help you make a decision on the purchase.
If you already are a holder of Poulan XT24H48YT, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Poulan XT24H48YT.
However, one of the most important roles played by the user manual is to help in solving problems with Poulan XT24H48YT. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Poulan XT24H48YT along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
