Instruction/ maintenance manual of the product 8935 Atwood
Go to page of 7
1 THIS INSTRUCTION MANUAL IS FOR USE BY AN AUTHORIZED SERVICE TECHNICIAN TO INST ALL AN A TWOOD - hydro flame TM FURNACE . INST ALLER : LEA VE THIS MANUAL WITH APPLIANCE . CONSUMER : RET AIN THIS MANUAL FOR FUR THER REF - ERENCE . This furnace design has been certified for installation in recre- ation vehicles as a MSP Category III furnace.
2 MINIMUM CLEARANCE TO FLOORBOARDS, W ALLS & SIMILAR COMBUSTIBLE BUILDING MATERIALS* MUST BE PROVIDED THE FULL LENGTH AND WIDTH OF UNIT HORIZONT AL TOP ----1/2˝ BOTTOM --3/16˝ SIDES ----1˝ REAR.
3 CAUTION PERSONAL INJUR Y • DO NOT allow furnace tabs to protrude through side wall cutout opening during installation process until door is installed and tabs are bent over . T abs have sharp edges. Place furnace in cavity . Do not have tabs protrude outside exterior wall until door is ready to be installed.
4 120 VOL T AC MODELS Route 120 volt AC and thermostat leads to wires located on the left side of control box using a minimum of 18 GA wire. The furnace must be installed so electrical components are protected from water . T o make electrical connections see WIRING DIAGRAM FIG 12 1.
5 3. A. When set for LP and NA T is required: Rotate plug and replace into valve tower . NA T SHOULD NOW BE VISIBLE FIG 5 B. When set for NA T and LP is required: Rotate plug and replace into valve tower . LP SHOULD NOW BE VISIBLE FIG 5 4. Check rod for proper positioning while tightening plug into tower .
E F A B C D 3 4 A B D C 10 1 D B A C G F E 5 1-1/4" 1-1/4" AV ANT DU VEHICULE Access to Static Pressure T ap (Accès à l’orifice Statique) OR 6 7 8 8 1-A OR 8 7 6 8 OR 3-A MUST USE MUST U.
7 2 13 35 14 37 32 30 11 10 3 4 31 33 29 7 6 17 36 25 5 18 23 34 28 9 16 8 40 38 24 20 39 19 43 44 45 42 41 DRA WING # DESCRIPTION OF PARTS 1 Relay 2 Thermostat - specify color 3 Duct Cover Plate 4 Du.
An important point after buying a device Atwood 8935 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Atwood 8935 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Atwood 8935 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Atwood 8935 you will learn all the available features of the product, as well as information on its operation. The information that you get Atwood 8935 will certainly help you make a decision on the purchase.
If you already are a holder of Atwood 8935, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Atwood 8935.
However, one of the most important roles played by the user manual is to help in solving problems with Atwood 8935. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Atwood 8935 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
