Instruction/ maintenance manual of the product PB22H46YTX Poulan
Go to page of 60
OPERA TOR'S MANU AL MODEL: PB22H46YTX L A WN TRACTOR AL W A YS WEAR EYE PROTECTION DURING OPERA TION Visit our website: www .poulan-pro.com WARNING: Read this Man u al and follow all Warnings and Safety Instructions. F ail ure to do so can re sult in serious in ju ry .
2 I. GENERAL OPERA TION • Read, understand, and follow all instructions on the machine and in the manual before starting. • Do not put hands or feet near rotating parts or under the machine. Keep clear of the discharge opening at all times. • Only allow responsible adults, who are familiar with the in struc tions, to operate the machine.
3 • Be sure the area is clear of bystanders before operat- ing. Stop machine if anyone enters the area. • Never carry passengers. • Do not mow in reverse unless absolutely necessary . Al ways look down and behind before and while back- ing. • Never carry children, even with the blades shut off.
4 SAFETY RULES ............................................................ 2 PRODUCT SPECIFICA TIONS ....................................... 4 CUSTOMER RESPONSIBILITIES ................................. 4 ASSEMBL Y ...................................
5 UNAS SEMBLED P ARTS (2) Keys Slope Sheet Key (1) Oil Drain Tube AS SEMBL Y When right or left hand is mentioned in this man ual, it means when you are in the operating po si tion (seated be hind the steer ing wheel). TO REMOVE TRACTOR FROM CAR TON UNP ACK CARTON • Remove all accessible loose parts and parts cartons from carton.
6 AS SEMBL Y CHECK TIRE PRESSURE The tires on your tractor were overinflated at the factory for shipping purposes. Correct tire pressure is important for best cutting performance. • Reduce tire pressure to PSI shown on tires. CHECK DECK LEVELNESS For best cutting results, mower housing should be properly leveled.
7 OPERA TION These symbols may appear on your tractor or in literature supplied with the product. Learn and understand their mean- ing. DANGER, KEEP HANDS AND FEET AWAY FREE WHEEL (Automatic Models on.
8 OPERA TION KNOW YOUR TRACTOR READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERA TING YOUR TRACTOR Compare the illustrations with your tractor to familiarize yourself with the locations of various controls and ad just ments. Save this manual for future reference.
9 GROUND DRIVE - • T o stop ground drive, depress brake pedal into full “BRAKE” position. IMPORT ANT : FORWARD AND REVERSE DRIVE PEDALS RETURN TO NEUTRAL POSITION WHEN NOT DEPRESSED. ENGINE - • Move throttle control between half and full speed (fast) position.
10 OPERA TION TO ADJUST MOWER CUT TING HEIGHT (See Fig. 8) The po si tion of the at tach ment lift le ver (A) de ter mines the cut ting height. • Put attachment lift lever in desired cutting height slot. The cutting height range is ap prox i mate ly 1" to 4".
11 OPERA TION FIG. 11 TOWING CARTS AND OTHER A T T ACH MENTS T ow only the attachments that are recommended by and comply with specifications of the manufacturer of your trac- tor . Use common sense when towing. T oo heavy of a load, while on a slope, is dangerous.
12 ADD GASOLINE • Fill fuel tank to bottom of filler neck. Do not overfill. Use fresh, clean, regular un lead ed gasoline with a minimum of 87 octane. (Use of leaded gasoline will increase carbon and lead oxide deposits and reduce valve life). Do not mix oil with gasoline.
13 4. Depress forward drive pedal to full forward position, hold for five (5) seconds and release pedal. Depress reverse drive pedal to full reverse position, hold for five (5) seconds and release pedal. Repeat this procedure three (3) times. 5. Shut- off engine and set parking brake.
14 MAINTENANCE T R A C T 0 R Inspect Muffler/Spark Arrester Clean Air Filter Change Engine Oil (with oil filter) Replace Air Filter Paper Cartridge Replace Spark Plug Check Engine Oil Level Clean Engine Cooling Fins Clean Air Screen 1 - Change more often when operating under a heavy load or in high ambient temperatures.
15 MAINTENANCE FIG. 13 02 544 MANDREL ASSEMBL Y BL ADE BL ADE BOL T (SPECIAL) CENTER HOLE ST AR BA TTERY Y our tractor has a battery charging system which is suf fi cient for normal use. However , periodic charging of the battery with an automotive charger will extend its life.
16 MAINTENANCE V -BEL TS Check V -belts for deterioration and wear after 100 hours of operation and replace if necessary . The belts are not ad just able. Re place belts if they begin to slip from wear . TRANSAXLE COOLING The transmission fan and cooling fins should be kept clean to assure proper cooling.
17 MAINTENANCE MUFFLER Inspect and replace corroded muffler and spark arrester (if equipped) as it could create a fire hazard and/or dam- age. SP ARK PLUGS Replace spark plugs at the beginning of each mowing season or after every 100 hours of operation, whichever occurs first.
18 D C G E F M L K R Q A P G B FIG. 17 SERVICE AND ADJUSTMENTS WARNING: TO A VOID SERIOUS INJURY , BEFORE PERFORMING ANY SER VICE OR AD JUST MENTS: • Depress brake pedal fully and set parking brake. • Place attachment clutch in “DISENGAGED” position.
19 SERVICE AND ADJUSTMENTS D C G E F M L K R Q A P G B on rear mower bracket and secure with washer and retainer spring. • A TT ACH FRONT LINK (E) - Work from left side of trac- arm (R). • Push clutch cable housing guide (P) into bracket, slide collar (L) onto guide and secure with retainer spring (K).
20 SERVICE AND ADJUSTMENTS TO LEVEL MOWER Make sure tires are properly inflated to the PSI shown on tires. If tires are over or under inflated, it may affect the appearance of your lawn and lead you to think the mower is not adjusted properly . VISUAL SIDE- TO -SIDE ADJUSTMENT (See Fig.
21 SERVICE AND ADJUSTMENTS FIG. 26 R R S M TO REPL ACE MOWER DRIVE BEL T MOWER DRIVE BEL T REMOVAL (See Fig. 26) - • P ark tractor on a level surface. Engage parking brake. Disengage attachment clutch control. • Remove screws from L.H. mandrel cover and remove cover .
22 TO ST ART ENGINE WITH A WEAK BA TTERY (See Fig. 30) WARNING : Lead-acid batteries gen- er ate ex plo sive gases. Keep sparks, flame and smoking ma te ri als away from bat ter ies. Always wear eye pro tec tion when around batteries. If your battery is too weak to start the engine, it should be recharged.
23 FIG. 30 WEAK OR DEAD BA TTERY FULL Y CHARGED BA TTERY SERVICE AND ADJUSTMENTS REPL ACING BA TTERY (See Fig. 31) WARNING: Do not short battery ter mi - nals by allowing a wrench or any other object to contact both terminals at the same time. Before connecting battery , remove metal bracelets, wristwatch bands, rings, etc.
24 STORAGE Immediately prepare your tractor for storage at the end of the season or if the tractor will not be used for 30 days or more. WARNING: Never store the trac tor with gas o line in the tank inside a building where fumes may reach an open flame or spark.
25 TROUBLESHOOTING POINTS Will not start 1. Out of fuel. 1. Fill fuel tank. 2. Engine not “CHOKED” properly . 2. See “TO ST ART ENGINE” in Operation section. 3. Engine flooded. 3. Wait several minutes before attempting to start. 4. Bad spark plug.
26 TROUBLESHOOTING POINTS Engine dies when 1. Reverse operation system 1. T urn ignition key to tractor is shifted (ROS) is not "ON" while ROS "ON" position. into reverse mower or other attachment See Operation section. is engaged.
27 LIMITED W ARRANTY The Manufacturer warrants to the original consumer purchaser that this product as manufactured is free from defects in materi- als and work man ship.
28 SERVICE NOTES.
29 15 DEGREES MAX. FOLD ALONG DOTTED LINE THIS IS A 15 DEGREE SLOPE ONLY RIDE UP AND DOWN HILL, NOT ACROSS HILL SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION WARNING: To avoid serious injury, operate your tractor up and down the face of slopes, never across the face.
This product has been expertly en gi neered and carefully manu fac tured to rigid quality stan dards. As with all mechanical products, some adjustments or part replacement may be necessary during the life of your unit.
This product has been expertly en gi neered and carefully manu fac tured to rigid quality stan dards. As with all mechanical products, some adjustments or part replacement may be necessary during the life of your unit.
29 15 DEGREES MAX. FOLD ALONG DOTTED LINE THIS IS A 15 DEGREE SLOPE ONLY RIDE UP AND DOWN HILL, NOT ACROSS HILL SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION WARNING: To avoid serious injury, operate your tractor up and down the face of slopes, never across the face.
28 SERVICE NOTES.
27 LIMITED W ARRANTY The Manufacturer warrants to the original consumer purchaser that this product as manufactured is free from defects in materi- als and work man ship.
26 TROUBLESHOOTING POINTS Engine dies when 1. Reverse operation system 1. T urn ignition key to tractor is shifted (ROS) is not "ON" while ROS "ON" position. into reverse mower or other attachment See Operation section. is engaged.
25 TROUBLESHOOTING POINTS Will not start 1. Out of fuel. 1. Fill fuel tank. 2. Engine not “CHOKED” properly . 2. See “TO ST ART ENGINE” in Operation section. 3. Engine flooded. 3. Wait several minutes before attempting to start. 4. Bad spark plug.
24 STORAGE Immediately prepare your tractor for storage at the end of the season or if the tractor will not be used for 30 days or more. WARNING: Never store the trac tor with gas o line in the tank inside a building where fumes may reach an open flame or spark.
23 FIG. 30 WEAK OR DEAD BA TTERY FULL Y CHARGED BA TTERY SERVICE AND ADJUSTMENTS REPL ACING BA TTERY (See Fig. 31) WARNING: Do not short battery ter mi - nals by allowing a wrench or any other object to contact both terminals at the same time. Before connecting battery , remove metal bracelets, wristwatch bands, rings, etc.
22 TO ST ART ENGINE WITH A WEAK BA TTERY (See Fig. 30) WARNING : Lead-acid batteries gen- er ate ex plo sive gases. Keep sparks, flame and smoking ma te ri als away from bat ter ies. Always wear eye pro tec tion when around batteries. If your battery is too weak to start the engine, it should be recharged.
21 SERVICE AND ADJUSTMENTS FIG. 26 R R S M TO REPL ACE MOWER DRIVE BEL T MOWER DRIVE BEL T REMOVAL (See Fig. 26) - • P ark tractor on a level surface. Engage parking brake. Disengage attachment clutch control. • Remove screws from L.H. mandrel cover and remove cover .
20 SERVICE AND ADJUSTMENTS TO LEVEL MOWER Make sure tires are properly inflated to the PSI shown on tires. If tires are over or under inflated, it may affect the appearance of your lawn and lead you to think the mower is not adjusted properly . VISUAL SIDE- TO -SIDE ADJUSTMENT (See Fig.
19 SERVICE AND ADJUSTMENTS D C G E F M L K R Q A P G B on rear mower bracket and secure with washer and retainer spring. • A TT ACH FRONT LINK (E) - Work from left side of trac- arm (R). • Push clutch cable housing guide (P) into bracket, slide collar (L) onto guide and secure with retainer spring (K).
18 D C G E F M L K R Q A P G B FIG. 17 SERVICE AND ADJUSTMENTS WARNING: TO A VOID SERIOUS INJURY , BEFORE PERFORMING ANY SER VICE OR AD JUST MENTS: • Depress brake pedal fully and set parking brake. • Place attachment clutch in “DISENGAGED” position.
17 MAINTENANCE MUFFLER Inspect and replace corroded muffler and spark arrester (if equipped) as it could create a fire hazard and/or dam- age. SP ARK PLUGS Replace spark plugs at the beginning of each mowing season or after every 100 hours of operation, whichever occurs first.
16 MAINTENANCE V -BEL TS Check V -belts for deterioration and wear after 100 hours of operation and replace if necessary . The belts are not ad just able. Re place belts if they begin to slip from wear . TRANSAXLE COOLING The transmission fan and cooling fins should be kept clean to assure proper cooling.
15 MAINTENANCE FIG. 13 02 544 MANDREL ASSEMBL Y BL ADE BL ADE BOL T (SPECIAL) CENTER HOLE ST AR BA TTERY Y our tractor has a battery charging system which is suf fi cient for normal use. However , periodic charging of the battery with an automotive charger will extend its life.
14 MAINTENANCE T R A C T 0 R Inspect Muffler/Spark Arrester Clean Air Filter Change Engine Oil (with oil filter) Replace Air Filter Paper Cartridge Replace Spark Plug Check Engine Oil Level Clean Engine Cooling Fins Clean Air Screen 1 - Change more often when operating under a heavy load or in high ambient temperatures.
13 4. Depress forward drive pedal to full forward position, hold for five (5) seconds and release pedal. Depress reverse drive pedal to full reverse position, hold for five (5) seconds and release pedal. Repeat this procedure three (3) times. 5. Shut- off engine and set parking brake.
12 ADD GASOLINE • Fill fuel tank to bottom of filler neck. Do not overfill. Use fresh, clean, regular un lead ed gasoline with a minimum of 87 octane. (Use of leaded gasoline will increase carbon and lead oxide deposits and reduce valve life). Do not mix oil with gasoline.
11 OPERA TION FIG. 11 TOWING CARTS AND OTHER A T T ACH MENTS T ow only the attachments that are recommended by and comply with specifications of the manufacturer of your trac- tor . Use common sense when towing. T oo heavy of a load, while on a slope, is dangerous.
10 OPERA TION TO ADJUST MOWER CUT TING HEIGHT (See Fig. 8) The po si tion of the at tach ment lift le ver (A) de ter mines the cut ting height. • Put attachment lift lever in desired cutting height slot. The cutting height range is ap prox i mate ly 1" to 4".
9 GROUND DRIVE - • T o stop ground drive, depress brake pedal into full “BRAKE” position. IMPORT ANT : FORWARD AND REVERSE DRIVE PEDALS RETURN TO NEUTRAL POSITION WHEN NOT DEPRESSED. ENGINE - • Move throttle control between half and full speed (fast) position.
8 OPERA TION KNOW YOUR TRACTOR READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERA TING YOUR TRACTOR Compare the illustrations with your tractor to familiarize yourself with the locations of various controls and ad just ments. Save this manual for future reference.
7 OPERA TION These symbols may appear on your tractor or in literature supplied with the product. Learn and understand their mean- ing. DANGER, KEEP HANDS AND FEET AWAY FREE WHEEL (Automatic Models on.
6 AS SEMBL Y CHECK TIRE PRESSURE The tires on your tractor were overinflated at the factory for shipping purposes. Correct tire pressure is important for best cutting performance. • Reduce tire pressure to PSI shown on tires. CHECK DECK LEVELNESS For best cutting results, mower housing should be properly leveled.
5 UNAS SEMBLED P ARTS (2) K e y s Slope Sheet Key (1) O i l D rain Tu be AS SEMBL Y When right or left hand is mentioned in this man ual, it means when you are in the operating po si tion (seated be hind the steer ing wheel). TO REMOVE TRACTOR FROM CAR TON UNP ACK CARTON • Remove all accessible loose parts and parts cartons from carton.
4 SAFETY RULES ............................................................ 2 PRODUCT SPECIFICA TIONS ....................................... 4 CUSTOMER RESPONSIBILITIES ................................. 4 ASSEMBL Y ...................................
3 • Be sure the area is clear of bystanders before operat- ing. Stop machine if anyone enters the area. • Never carry passengers. • Do not mow in reverse unless absolutely necessary . Al ways look down and behind before and while back- ing. • Never carry children, even with the blades shut off.
2 I. GENERAL OPERA TION • Read, understand, and follow all instructions on the machine and in the manual before starting. • Do not put hands or feet near rotating parts or under the machine. Keep clear of the discharge opening at all times. • Only allow responsible adults, who are familiar with the in struc tions, to operate the machine.
OPERA TOR'S MANU AL MODEL: PB22H46YTX L A WN TRACTOR AL W A YS WEAR EYE PROTECTION DURING OPERA TION Visit our website: www .poulan-pro.com WARNING: Read this Man u al and follow all Warnings and Safety Instructions. F ail ure to do so can re sult in serious in ju ry .
An important point after buying a device Poulan PB22H46YTX (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Poulan PB22H46YTX yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Poulan PB22H46YTX - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Poulan PB22H46YTX you will learn all the available features of the product, as well as information on its operation. The information that you get Poulan PB22H46YTX will certainly help you make a decision on the purchase.
If you already are a holder of Poulan PB22H46YTX, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Poulan PB22H46YTX.
However, one of the most important roles played by the user manual is to help in solving problems with Poulan PB22H46YTX. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Poulan PB22H46YTX along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
