Instruction/ maintenance manual of the product 437126 Poulan
Go to page of 44
OWNER'S MANUAL MODEL NUMBER: PP1150E27 SNOW THROWER Always W ear Eye Protection During Operation IMPORT ANT MANU AL Do Not Throw Away WARNING: Read the Owner's Manual and fol low all W arnings and Safety In struc tions. F ail ure to do so can result in serious injury .
2 IMPORT ANT Safe Operation Practices for W alk-Behind Snow Throwers This snow thrower is capable of amputating hands and feet and throwing objects. F ailure to observe the following safety instructions could result in serious injury . WARNING: This snow thrower is for use on sidewalks, driveways and other ground level surfaces.
3 6. When cleaning, repairing or inspecting the snow thrower , stop the engine and make certain the collector/impel- ler and all moving parts have stopped. Disconnect the spark plug wire and keep the wire away from the plug to prevent someone from accidentally starting the engine.
4 (1) POWER CORD (198563) (1) DISCHARGE CHUTE (1) LOCKNUT 5/16-18 (751153) (1) CARRIAGE BOL T 5/16-18 x 5/8 (72250505) (1) LOCKNUT 1/4-20 (191730) (1) SHOULDER BOL T 1/4-20 (179829) (1) SPRING (184505.
5 AS SEMBL Y / PRE-OPERA TION SPEED CON TROL ROD SPEED CONTROL BRACKET RET AINER SPRING SPEED CONTROL LEVER FIG. 2 TRACTION DRIVE CON TROL ROD DRIVE CONTROL BRACKET RET AINER SPRING TRACTION DRIVE CON TROL LEVER FIG. 4 SPEED CONTROL ROD HANDLE KNOB L OWER HANDLE PL ASTIC TIE UPPER HANDLE FIG.
6 AS SEMBL Y / PRE-OPERA TION INST ALL DISCHARGE CHUTE / CHUTE ROT A TER HEAD (See Fig. 7) NOTE: The multi-wrench provided in your parts bag may be used to install the chute rotater head. 1. Place discharge chute assembly on top of chute base with discharge opening toward front of snow thrower .
7 CHECK TIRE PRESSURE The tires on your snow thrower were overinflated at the fac- tory for shipping purposes. Correct and equal tire pres sure is important for best snow throwing performance. • Reduce tire pressure to 14-17 PSI. AS SEMBL Y / PRE-OPERA TION CHUTE DEFLECTOR CONTROL LEVER FIG.
8 OPERA TION KNOW YOUR SNOW THROWER READ THIS OWNER'S MANUAL AND ALL SAFETY RULES BEFORE OPERA TING YOUR SNOW THROWER. Compare the illustrations with your snow thrower to familiarize yourself with the location of various controls and adjustments.
9 MUF FLER GAS O LINE FILLER CAP SAFETY IGNITION KEY CHOKE CON- TROL PRIM ER RECOIL (AUXILIARY) ST ARTER HANDLE ELECTRIC ST ART BUTTON ON / OFF SWITCH OPERA TION LH and RH turn triggers - used to steer the snow thrower . Drive speed control lever - used to select forward or reverse motion and speed of snow thrower .
10 The operation of any snow thrower can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields while operating your snow thrower or performing any ad just- ments or repairs. We recommend standard safe ty glasses or a wide vision safety mask worn over spectacles.
11 TO MOVE FORWARD AND BACK WARD (See Fig. 15) SELF-PROPELLING, forward and reverse movement of the snow thrower , is controlled by the traction drive control lever located on the left side handle. • Squeeze traction drive control lever to handle to en gage the drive system.
12 TO ADJUST SKID PL A TES (See Fig. 17) NOTE: The wrench provided in your parts bag may be used to adjust the skid plates. Skid plates are located on each side of the auger housing and adjust the clearance between the scraper bar and the ground surface.
13 OPERA TION SNOW THROWING TIPS • Go slower in deep, freezing or heavy wet snow . Use the drive speed control, NOT the ON / OFF switch, to adjust speed. • It is easier and more efficient to remove snow im me- di ate ly after it falls. • The best time to remove snow is the early morning.
14 MAINTENANCE LUBRICA TION CHART GENERAL REC OM MEN DA TIONS The warranty on this snow thrower does not cover items that have been sub ject ed to operator abuse or negligence. T o receive full value from the warranty , operator must maintain snow thrower as in struct ed in this manual.
15 MAINTENANCE BEL TS Check belts for deterioration and wear after every 50 hours of operation and replace if necessary . The belts are not ad just able. Replace belts if they begin to slip from wear . (See “TO REMOVE BEL T COVER” in the Service and Adjustments section of this manual).
16 SERVICE AND ADJUSTMENTS TO REMOVE BEL T COVER (See Fig. 20) 1. Remove the two (2) screws securing belt cover to frame. 2. Remove belt cover . 3. Replace belt cover by installing cover and screws and tighten securely . FRAME BEL T COVER SCREWS FIG. 20 WARNING: T o avoid serious injury , before performing any service or ad just ments: 1.
17 SERVICE AND ADJUSTMENTS 8. RELIEVE TENSION ON TRACTION DRIVE BEL T IDLER and remove traction drive belt from around pulleys. HINT : Insert a 3/8" drive ratchet (in the “ON” position) into the square hole in idler arm and rotate ratchet clockwise to relieve tension.
18 ENGINE See engine manual. CARBURETOR Y our carburetor is not adjustable. Engine performance should not be affected at altitudes up to 7,000 feet (2,134 meters). If your engine does not operate properly due to suspected carburetor problems, take your snow thrower to a qualified service center .
19 STORAGE Immediately prepare your snow thrower for storage at the end of the season or if the unit will not be used for 30 days or more. WARNING: Never store the snow thrower with gaso line in the tank in side a build ing where fumes may reach an open flame, spark or pilot light as on a fur nace, water heater , clothes dryer or gas ap pli ance.
20 TROUBLESHOOTING Does not start 1. Fuel shut-off valve (if so 1. T urn fuel shut-off valve to OPEN position. equipped) in OFF position. 2. Safety ignition key 2. Insert safety ignition key . is not inserted. 3. Out of fuel. 3. Fill fuel tank with fresh, clean gasoline.
21 SERVICE NOTES.
22 10 11 11 11 11 1 2 3 4 5 6 7 9 9 9 8 12 12 13 14 15 16 17 18 19 20 21 21 22 22 23 23 24 25 26 27 28 29 30 31 31 32 33 34 35 36 37 37 01.07.026-D 2 (EXPL ODED) REP AIR P ARTS SNOW THROWER - - MODEL NUMBER PP1150E27 (96198003303) AUGER HOUSING / IMPELLER ASSEMBL Y NOTE: All component dimensions given in U.
23 NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty . KEY P ART NO .
24 NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty . KEY P ART NO .
25 KEY P ART NO . NO . DESCRIPTION 1 2 3 3 4 01.11.001-B 4 KEY P ART NO . NO . DESCRIPTION NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty .
26 KEY P ART NO . NO . DESCRIPTION NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty .
27 NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty . KEY P ART NO .
28 NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty . KEY P ART NO .
29 NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty . KEY P ART NO .
30 NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty . KEY P ART NO .
31 NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty . KEY P ART NO .
32 9 9 11 11 11 1 2 3 21 5 6 12 13 14 15 20 15 16 17 10 9 8 7 23 19 53 53 53 53 25 26 26 27 39 40 41 42 43 44 32 38 53 53 37 36 35 39 33 28 30 29 31 4 23 24 24 01.02.013-A 18 42 EXPL ODED 24 23 24 33 34 22 47 49 50 48 52 51 46 45 4 REP AIR P ARTS SNOW THROWER - - MODEL NUMBER PP1150E27 (96198003303) DRIVE NOTE: All component dimensions given in U.
33 NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty . KEY P ART NO .
34 KEY P ART NO . NO . DESCRIPTION NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty .
35 NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts.
36 KEY P ART NO . NO . DESCRIPTION KEY P ART NO . NO . DESCRIPTION NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty .
37 NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty . KEY P ART NO .
38 NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty . REP AIR P ARTS SNOW THROWER - - MODEL NUMBER PP1150E27 (96198003303) WHEELS KEY P ART NO .
39 KEY P ART NO . NO . DESCRIPTION NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty .
40 KEY P ART NO . NO . DESCRIPTION KEY P ART NO . NO . DESCRIPTION 1 01.14.007-A 1 193071 SAFETY IGNITION KEY REP AIR P ARTS SNOW THROWER - - MODEL NUMBER PP1150E27 (96198003303) BAG OF P ARTS NOTE: All component dimensions given in U.S. inches. 1 inch = 25.
41 KEY P ART NO . NO . DESCRIPTION REP AIR P ARTS SNOW THROWER - - MODEL NUMBER PP1150E27 (96198003303) BAG OF P ARTS NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts.
42 KEY P ART NO . NO . DESCRIPTION NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty .
43 SERVICE NOTES.
LIMITED W ARRANTY The Manufacturer warrants to the original consumer purchaser that this product as manufactured is free from defects in materials and work man ship.
An important point after buying a device Poulan 437126 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Poulan 437126 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Poulan 437126 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Poulan 437126 you will learn all the available features of the product, as well as information on its operation. The information that you get Poulan 437126 will certainly help you make a decision on the purchase.
If you already are a holder of Poulan 437126, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Poulan 437126.
However, one of the most important roles played by the user manual is to help in solving problems with Poulan 437126. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Poulan 437126 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
