Instruction/ maintenance manual of the product ITT4100 POSline
Go to page of 34
ITT4100 POSline® Thermal T ransfer Printer User's Manua l.
.
2. Power Supply 3. Parts and Features WARNING: NEVER OPERATE TH E PRINTER AND POWER SU PPLY IN AN AREA WHERE THEY CAN GET WET. 1. The Power Adapter has a barrel connector on one end that must be inserted into the power jack on the back of the printer.
4. Loading the Ribbon Note: Media Hanger This section is not applicable to the direct thermal printing. Ribbon Pick-up Holder Release Levers 1. Lift the top cover to expose the media compartment.
2. Unlatch the print head module by pushing the two white release levers on the sides toward the rear . 3. T urn over the print head module to expose the ribbon supply holder . Ribbon Supply Holder Release Lever Print Head Module 8 4. Unwrap the ribbon roll pack and separate the ribbon roll and the bare core.
7. Turn back the print head module and then insert the bare core into the pick-up holder. (First snap in the left side, then the right side.) 8. Turn the wheel of the print head module to ensure the ribbon is tightly wound. 10 9. Press down the print head modul e on both sides firmly till you hear a snap.
5. Loading the Media 2. Remove the media hanger. 3. Load the media roll onto the hanger. 4. Unlatch the print head module. A Series printers can be operated in three different options: standard, peel-off, or with a cutter. 5. Left the peeler cover easy for label easy into the slot.
6. Lead the label through the media guides with the other hand. The media guide can be adjusted centrality to well fit with different label width. 7. Press down the print head module firmly on both sides till you hear a snap.
Peel Off Mode 8. Close the top cover and turn on the printer or press the feed button if the printer is already on. 1. Loose two attached screws on the back of peeler cover.
3. Plug in the dispenser connecter. 5. Secure two attached screws on the back of peeler cover. 4. Mount the dispenser module. 6. Lead the label through the media guides and dispenser.
7. Press down the print head module firmly till you hear a snap. 9. Press the feed button and the label backing paper will come out from the slot under dispenser. 8. Close the top cover and turn on the printer or press the feed button if the printer is already on.
Cutter Mode 4. Loose the screw on the printer module. 5. Remove the dispenser bar. 1. First plug cutter baby board in JP29 on the main board. 2. Loose two attached screws on the back of peeler cover.
6. Plug in the cutter connecter. 8. Lead the label through the media guides and the slot of cutter. 7. Secure the screw of cutter module. 24 9. Press down the print head module firmly on both sides till you hear a snap.
6. Operator Controls 10. Close the top cover and turn on the printer or press the feed button if the printer is already on. Power Switch Controls printer power Feed Button On-normal operation Off-the .
7. Performing Calibration Ready Indicator T op Cover Power Indicator Feed Button 1. Keep pressing the feed button while turning on the power, until the printing motor becomes activated. 2. The calibration has been performed while the printer automatically feed label stock for certain length.
8. Printing Configuration Report 9. Resetting the Printer to Factory Default Settings 1. Keep pressing the feed button while turning on the power, until the printing motor becomes activated.
10. Hooking up the Printer and Computer Power Jack Note : The power supply barrel connector must be inserted into the power jack on the back of the printer before connecting the communication cables.
11. Communicating with the Printer Parallel Interface Requirements The required cable (IEEE 1284-compliant is recommended) must have a standard 36-pin parallel connector on one end, which is plugged into the parallel port located on the back of the printe r.
Installing USB Driver (Windows 98 only) → Click “Next “. → Select "Specify ❑ Install USB driver Properties menu → Right click to get pop-up menu. Notes: Uninstall printer driver before installing USB driver. → Select "Driver".
Installing Printer Driver Notes : 1. If you are just updating your driver, make sure to delete the previous version first. 1. Click the "Start" button. 2. Uninstall printer driver before installing USB driver. 2. Select "Settings", then select "Printers" and double click the "Add Printer" icon.
Set the Parameters For Win 98 / ME After installing the driver, you can follow the path below to set parameters: ❑ Ports Properties menu Start → Settings → Printers → Label Dr. → Properties → Click "Details". → Select the IO port.
❑ Output bin 41 (Accessory setting) Properties menu → Click "Paper". → Click "more option". → Select Enable/without cutter, peeler. → Click "OK". ❑ Print quality (Speed) Properties menu → Click "Device Options".
For Win 2000 ❑ Ports Properties menu → Click "Ports". → Select the IO port. → Click "OK". ❑ Paper source (Media type) Back to Printers menu → Right click to get pop-up menu. → Select "Printing Reference". → Click "Paper Quality" select media type.
For NT 4.0 ❑ Create a new size Printer menu → Right click to get pop- up menu on empty space. → Select "Server Properties". → Enter a form name for the new form in "Form description for". → Reset the paper size in the specific squares of the "Measurements ".
For Win XP ❑ Paper/Output (Speed) ❑ Print quality (Darkness) Default Document menu → C lick "Advanced". → C lick each item to select desired parameter. → C lick "OK". ❑ Create a new size Please refer to the procedure of create a new size on Win 2000.
❑ Orientation 50 ❑ Create a new size Printing Reference menu Printer menu → Click "Layout". → Right click to get → Select "Portrait" or pop-up menu in "Landscape". blank space. → Click "OK". → Select "Server Properties".
12. Troubleshooting B. Power and Ready LEDs blink alternately Power LED Ready LED ON OFF OFF ON Normally, when the printer is in abnormal condition, the power LED will keep blinking. The printing work and the communication between the host and printer will stop.
Poor printout quality. D. Miscellaneous . The ribbon may not be qualified. The host shows "Printer Time out" . The media may not be qualified. 1. Check if the communication cabl e(parallel, serial or USB) is connected securely to your parallel or serial port on the PC and to the connector on the printer at the other end.
13. Caring for Your Printer Replacing Thermal Print Head 1. Switch off the power and wait for both LEDs to go off. Clean the following areas of the printer after 8 rolls of label st ocks have been used. In each case, use a cotton bud dampened with alcohol.
3. Loose the 4 screws (C) to take out print head from print head module (12, 13). 4. Unplug the 2 print head cables from the connectors on print head to take off the old print head. 5. Plug the 2 print head cable to the new print head. 6. Screw the new print head on print head module (12,13).
Fonts, Bar Codes and Graphics Specification Barcodes Code 39, Extended Code 39, Co de 93, Code 128 UCC Code 128(Subset A, B, C) Codab ar , Interleave 2 of 5, EAN-8 2&5 add on, EAN-13, EAN-128, UPC.
Interface Specifications 2. Since this printer uses band buffer technology, if you just print texts or barcodes the maximum length can be more than 30 inches, whereas if you print many graphics the maximum length can only be few inches under standard onboard RAM.
Connection with host: Host 25S Printer 9P Host 9S Printer 9P (PC or compatible) (PC or compatible) DTR 20 …… 1 DSR DTR 4 …… 1 DSR DSR 6 …… 6 DTR DSR 6 …… 6 DTR TX 2 …… 2 RX TX 3 .
Parallel (Centronics) ASCIITABLE The parallel port is a standard 36-pin Centronics. Its pin assignments are listed as following. 66 0 1 2 3 4 5 6 7 0 NUL 0 @ P ' P 1 SON XON ! 1 A Q a q 2 STX &qu.
An important point after buying a device POSline ITT4100 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought POSline ITT4100 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data POSline ITT4100 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, POSline ITT4100 you will learn all the available features of the product, as well as information on its operation. The information that you get POSline ITT4100 will certainly help you make a decision on the purchase.
If you already are a holder of POSline ITT4100, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime POSline ITT4100.
However, one of the most important roles played by the user manual is to help in solving problems with POSline ITT4100. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device POSline ITT4100 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
