Instruction/ maintenance manual of the product 33-411 Porter-Cable
Go to page of 28
INSTRUCTION MANUAL P ART NO. 424-03-651-0019 - 06-20-05 Copyright © 2004 Delta Machinery T o learn more about DEL T A MACHINER Y visit our website at: www .deltamachinery .com. For Parts, Service, W arranty or other Assistance, please call 1-800-223-7278 ( In Canada call 1-800-463-3582).
2 T ABLE OF CONTENTS Read and understand all warnings and operating instructions before using any tool or equipment. When using tools or equipment, basic safety precautions should always be followed to r educe the risk of personal injury .
3 Indicates an imminently hazardous situation which, if not avoided, will r esult in death or serious injury . Indicates a potentially hazardous situation which, if not avoided, could r esult in death or serious injury . Indicates a potentially hazardous situation which, if not avoided, may r esult in minor or moderate injury .
4 GENERAL SAFETY RULES READ AND UNDERST AND ALL W ARNINGS AND OPERA TING INSTRUCTIONS BEFORE USING THIS EQUIPMENT . Failure to follow all instructions listed below , may result in electric shock, fire, and/or serious personal injury or pr operty damage.
5 F AILURE TO FOLLOW THESE RULES MA Y RESUL T IN SERIOUS PERSONAL INJUR Y . ADDITIONAL SPECIFIC SAFETY RULES SA VE THESE INSTRUCTIONS. Refer to them often and use them to instruct others. 1 . DO NOT OPERA TE THIS MACHINE UNTIL it is assembled and installed according to the instructions.
Fig. 1 1. 3/8-16x1" Hex Head Screw (12) 2. 1/4-20x7/8" Round Head Screw (15) 3. 1/2-20x1/2" Hex Head Screw (4) 4. 3/8" Flat Washer (12) 5. 9/32" Flat Washer (15) 6. 3/8" Lockwasher (12) 7. 1/4" Lockwasher (4) 8. 3/8-16 Hex Nut (12) 9.
7 UNP ACKING AND CLEANING Carefully unpack the machine and all loose items fr om the shipping container(s). Remove the protective coating fr om all unpainted surfaces. This coating may be removed with a soft cloth moistened with kerosene (do not use acetone, gasoline or lacquer thinner for this purpose).
8 ELEV A TING CRANK HANDLE Assemble elevating crank handle (A) Fig. 6 to rod in front of base using the r oll pin (B). TRACK-ARM LOCK Assemble track-arm lock handle (A) to the overarm (Fig. 7), and tighten set screw (B). Lock handle (A) should be tight when in the position shown in Fig.
9 CUTTINGHEAD AND CROSS-CUT STOP TO TRACK-ARM 1. Remove two screws (A) and end cap (B) from track- arm, Fig. 8. 2. Hold cuttinghead assembly (D) Fig. 9, with both hands and insert the ball bearings (E) into the track- arm, as shown. Push cuttinghead all the way onto track-arm and tighten clamp knob (F).
10 ST AR TER BOX TO BASE 1. Assemble bracket (A) to the bottom of the right side of saw base, (Fig. 12), using the 1/4-20x1/2" hex head screw (B), 1/4" lockwasher (D), and 1/4-20 nut (E).
11 ADJUSTING T ABLE TOP P ARALLEL TO TRACK-ARM For accurate work the track-arm must be parallel to the table top at all points. T o check and adjust: 1. Move the motor and cuttinghead assembly (A) to the vertical position (Fig. 18). Position saw arbor (B) Fig.
12 3. IMPORT ANT : T o prevent arbor nut fr om spinning when blade stops, place the 1-1/16" wrench (C) Fig. 23 on flats of arbor and firmly tighten arbor nut (A) with the 1-5/8" box end spanner wrench (D) (left handed thread). Firmly tighten set scr ew (E).
13 4. Attach eyelet (H) Fig. 30 of cable assembly (C) to "S" bracket (E). 5. NOTE: T o prevent pr emature wear of r etur n reel cable, position the return reel so that the cable does not rub against the wall of the return reel. Fig. 30 H C E Fig.
14 T AKING SIDE MOTION OUT OF OVER-ARM 1. Loosen hex nuts (A) and gib adjusting scr ews (B) and (C) Fig. 31. 2. Loosen nuts (D) Fig. 31, and adjust bolts (E), so that base wraps around column secur ely . If column is tight in base, turn bolts (E) clockwise to loosen.
15 Fig. 33 Fig. 34 G ADJUSTING TRACK RODS Each track rod (A, B, C, D) Fig. 34 can be adjusted individually to present a new bearing surface. Adjust the track rods one at a time as follows: 1. Remove end cap (E) Fig. 35, cross-cut stop (F) and cutterhead assembly (G), from the track-arm (Fig.
16 ADJUSTING BLADE SQUARE WITH T ABLE TOP 1. Remove blade guard and place saw blade in cut-of f position over fixed portion of table. 2. Place a square (A) Fig. 36, against saw blade. Be sure squar e is on the table surface, and between the gullets of the teeth, not against the saw teeth.
17 1. Place a square (A) Fig. 40 against fence (B), and lower cuttinghead (C) so that saw blade just clears table top. 2. Pull cuttinghead (C) Fig. 40, along square (A). If saw blade does not travel parallel to the square, the following adjustment is necessary .
18 Even though the cuttinghead travel may be perfectly aligned at 90 degrees to the fence, the blade itself may not be 90 degrees or squar e with the fence, (Fig. 42). This condition is known as "heeling."T o check and adjust: 1. Cross-cut a board and see on which side of the cut board saw teeth marks appear .
19 ADJUSTING BLADE GUARD On all ripping and plowing operations, the back part of the blade guard is lower ed so that it just clears the material. This will prevent the material fr om being lifted off the table. Also, lower the kickback r od (A) Fig. 46, so that the kickback fingers are 1/8" below surface of material.
20 ADJUSTING TENSION ON CUTTINGHEAD RETURN ASSEMBL Y The cuttinghead return assembly is properly tensioned when ther e is just enough cable tension to return the cuttinghead (A) Fig. 49, without excessive force, to the r ear of the track arm (B) after completion of the cut.
21 CROSS-CUTTING Cross-cutting consists of supporting the workpiece against the fence and pulling the saw blade through the material at right angles to it. When cross-cutting, the track arm should be indexed at “0” and the track arm clamp handle tightened.
22 COMPOUND MITER CUTTING Compound miter cutting is performed in the same manner as miter cutting except the saw blade is also tilted to cut a bevel. The settings and operation ar e similar to miter cut ting except that the blade is first tilted to the desired angle on the bevel scale befor e it is clamped in place.
23 PUSH STICK Make from 1/2 ″ OR 3/4 ″ WOOD or thickness less than width of material to be cut. Cut her e to push 1/4 ″ wood. Cut her e to push 1/2 ″ wood.
24 TROUBLESHOOTING GUIDE For assistance with your tool, visit our website at www .deltamachinery .com for a list of service centers or call the DEL T A Machinery help line at 1-800-223-7278 (In Canada call 1-800-463-3582).
A complete line of accessories is available from your Delta Supplier , Porter -Cable • Delta Factory Service Centers, and Delta Authorized Service Stations. Please visit our W eb Site www .deltamachinery .com for a catalog or for the name of your nearest supplier .
26 NOTES.
27 NOTES.
The following are trademarks of POR TER-CABLE • DEL T A (Las siguientes son marcas registradas de POR TER-CABLE • DEL T A S.A.) (Les marques suivantes sont des marques de fabriquant de la POR TER-CABLE • DEL T A): Auto-Set ® , BAMMER ® , B.O.S.
An important point after buying a device Porter-Cable 33-411 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Porter-Cable 33-411 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Porter-Cable 33-411 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Porter-Cable 33-411 you will learn all the available features of the product, as well as information on its operation. The information that you get Porter-Cable 33-411 will certainly help you make a decision on the purchase.
If you already are a holder of Porter-Cable 33-411, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Porter-Cable 33-411.
However, one of the most important roles played by the user manual is to help in solving problems with Porter-Cable 33-411. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Porter-Cable 33-411 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
