Instruction/ maintenance manual of the product 325MAG Porter-Cable
Go to page of 15
Instruction manual The Model and Serial No. plate is located on the main housing of the tool. Record these numbers in the spaces below and retain for future reference. Model No. ______________________________________ Type ___________________________________________ Serial No.
2 SAFETY GUIDELINES - DEFINITIONS indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. indicates a potentially hazardous situation which, if not avoided,could result in death or serious injury.
3 3. Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock. 4. Do not abuse the cord. Never use the cord to carry the tools or pull the plug from an outlet. Keep cord away from heat, oil, sharp edges or moving parts.
4 ADDITIONAL SPECIFIC SAFETY RULES SERVICE 1. Tool service must be performed only by qualified repair personnel. Service or maintenance performed by unqualified personnel could result in a risk of injury. 2. When servicing a tool, use only identical replacement parts.
5 z When the blade is pinched or bound tightly by the kerf closing down, the blade stalls and the motor reaction drives the unit rapidly back toward the operator.
6 EXTENSION CORD SELECTION If an extension cord is used, make sure the conductor size is large enough to prevent excessive voltage drop which will cause loss of power and possible motor damage. A table of recommended extension cord sizes will be found in this section.
7 Length of Cord in Feet 115V 25 Ft. 50 Ft. 100 Ft. 150 Ft. 200 Ft. 250 Ft. 300 Ft. 400 Ft. 500 Ft. 230V 50 Ft. 100 Ft. 200 Ft. 300 Ft. 400 Ft. 500 Ft.
2. While pressing the arbor lock button, extend the lever on the Quik- Change blade clamp (A) Fig. 2 and turn it counter-clockwise. 3. Remove the Quik-Change blade clamp, release the arbor lock button, and remove the outer blade flange. 4. Retract the telescoping guard (A) Fig.
9 The telescoping guard (A) Fig. 3 is a safety device important to your protection. Every time you use the saw, verify that the telescoping guard rotates freely and returns quickly and completely to its closed position. At least once a month, remove any accumulated debris (sawdust, pitch, etc.
10 0° POSITIVE STOP The saw is equipped with an adjustable positive stop at 0°. Check the accuracy of this stop periodically. To adjust: 1. Loosen the bevel adjustment lever (A) Fig. 8, and position the base for a 0° cut. Confirm that the bevel-stop sleeve (B) Fig.
11 INSTALLING THE OPTIONAL RIP GUIDE 1. Insert the rip guide (A) Fig. 14 through the slots (B). Slide the guide in until it extends through the both slots in the sawbase. 2. Place the compression spring on the thumb screw (C) Fig. 14 (supplied with the rip guide), and thread into the hole in the saw base.
12 CROSS-CUTTING Cutting directly across the grain of a piece of lumber is called crosscutting. Position the work so that the cut will be on the left. RIPPING Cutting wood lengthwise is referred to as ripping. This operation is performed in the same manner as crosscutting with the exception of supporting the workpiece.
13 KEEP TOOL CLEAN Periodically blow out all air passages with dry compressed air. All plastic parts should be cleaned with a soft damp cloth. NEVER use solvents to clean plastic parts. They could possibly dissolve or otherwise damage the material. Wear ANSI Z87.
14 A complete line of accessories is available from your Porter-Cable • Delta Supplier, Porter-Cable • Delta Factory Service Centers, and Porter- Cable Authorized Service Stations. Please visit our Web Site www.porter-cable.com for a catalog or for the name of your nearest supplier.
The following are trademarks of PORTER-CABLE • DELTA (Las siguientes son marcas registradas de PORTER-CABLE • DELTA S.A.) (Les marques suivantes sont des marques de fabriquant de la PORTER-CABLE • DELTA): Auto-Set ® , BAMMER ® , B.
An important point after buying a device Porter-Cable 325MAG (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Porter-Cable 325MAG yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Porter-Cable 325MAG - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Porter-Cable 325MAG you will learn all the available features of the product, as well as information on its operation. The information that you get Porter-Cable 325MAG will certainly help you make a decision on the purchase.
If you already are a holder of Porter-Cable 325MAG, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Porter-Cable 325MAG.
However, one of the most important roles played by the user manual is to help in solving problems with Porter-Cable 325MAG. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Porter-Cable 325MAG along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
