Instruction/ maintenance manual of the product PAD4000.4 Polk Audio
Go to page of 34
4 -CHANNEL A MPLIFIER PA D4000.4 HBP2478.
2 © 2011 Polk Audio—all rights reserved © 2011 Polk Audio—all rights reserved 3 T ABLE OF CONTENTS INTRODUCTION ............................................................................... 3 WHA T’S IN THE BOX ..............................
4 © 2011 Polk Audio—all rights reserved © 2011 Polk Audio—all rights reserved 5 TOOLS OF THE TRADE Listed next are the majority of the tools required to perform an installation. Having the proper tools will make the installation that much easier .
6 © 2011 Polk Audio—all rights reserved © 2011 Polk Audio—all rights reserved 7 AMPLIFIER WIRING Power Connections • P A D4000.4Fuse Size:2 x40 AMPA TC • Powerconnections acceptup to4 AWGwire.
8 © 2011 Polk Audio—all rights reserved © 2011 Polk Audio—all rights reserved 9 9. Battery and ground connections to the vehicle should be made with crimped ring terminals of the appropriate size (surface area is what counts;) soldering the terminals after crimping is also recommended.
10 © 2011 Polk Audio—all rights reserved © 2011 Polk Audio—all rights reserved 11 Audio cycles on and off Thermal protection engages when amplifier heat sink temperature exceeds 85° C (185° F). Make sure there is proper ventilation for amplifier and improve ventilation as needed.
12 © 2011 Polk Audio—all rights reserved © 2011 Polk Audio—all rights reserved 13 T ABLE DES MA TIÈRES INTRODUCTION .............................................................................. 13 CONTENU DE LA BOÎTE .........................
14 © 2011 Polk Audio—all rights reserved © 2011 Polk Audio—all rights reserved 15 OUTILS REQUIS V oici uneliste dela plupartdes outilsrequis pourfaire l’installation. L ’utilisation d’outils appropriés rendra l’installation beaucoup plus facile.
16 © 2011 Polk Audio—all rights reserved © 2011 Polk Audio—all rights reserved 17 CÂBLAGE DE L ’AMPLIFICA TEUR Alimentation • P A D4000.4—typede fusibles:2 x40 AMPA TC. • Connexionde l’alimentation—câblede calibrejusqu’à 4AWG.
18 © 2011 Polk Audio—all rights reserved © 2011 Polk Audio—all rights reserved 19 9. Les connexions aux bornes de la batterie et à la masse doivent être faites à l’aide de cosses à sertir circulaires de format approprié (la surface de contact est primordiale).
20 © 2011 Polk Audio—all rights reserved © 2011 Polk Audio—all rights reserved 21 CONSEILS DE DÉP ANNAGE Symptôme Cause probable Solution Pas De Sortie Absence de contrôle à distance ou signal faible. Vériezlecontrôleàdistancedel’ampli et réparez au besoin.
22 © 2011 Polk Audio—all rights reserved © 2011 Polk Audio—all rights reserved 23 Amplificateur P A D4000.4 T ype Pontable Classe D MOSFET Canaux 4 canaux Puissance RMS continue @ 4 Ohms 125 W x 4 Puissance RMS continue @ 2 Ohms 200 W x 4 Puissance pontée @ 4 Ohms 400 W x 2 Distorsion à puissance nom.
24 © 2011 Polk Audio—all rights reserved © 2011 Polk Audio—all rights reserved 25 ESP AÑOL INTRODUCCIÓN Gracias por la compra de este amplificador de la serie P A D de Polk Audio.
26 © 2011 Polk Audio—all rights reserved © 2011 Polk Audio—all rights reserved 27 8. Conmutador delantero BPF , FULL o HPF— Selecciona Filtro de Paso de Banda (Band Pass Filter , BPF), rango completo (FULL) o Filtro de Pasaaltas (High Pass Filter , HPF).
28 © 2011 Polk Audio—all rights reserved © 2011 Polk Audio—all rights reserved 29 INST ALACIÓN DEL AMPLIFICADOR Ubicaciones de montaje La ubicación de su amplificador depende de varios factores importantes.
30 © 2011 Polk Audio—all rights reserved © 2011 Polk Audio—all rights reserved 31 CONFIGURACIÓN Y DETECCIÓN Y REP ARACIÓN DE A VERÍAS Prueba del sistema Después de terminar la instalación, es necesario poner a prueba el sistema. Esto contribuirá a garantizar años de funcionamiento sin problemas.
32 © 2011 Polk Audio—all rights reserved © 2011 Polk Audio—all rights reserved 33 Mala respuesta de bajos Los altavoces cableados con la polaridad equivocada causan cancelación a frecuencias bajas. Revise la polaridad de los altavoces y cámbiela según sea necesario.
34 © 2011 Polk Audio—all rights reserved © 2011 Polk Audio—all rights reserved 35 INHAL T EINFÜHRUNG ................................................................................ 35 KARTONINHAL T .............................................
36 © 2011 Polk Audio—all rights reserved © 2011 Polk Audio—all rights reserved 37 DIE WERKZEUGE Esfolgt eineListe derwichtigsten fürdie Installationnotwendigen Werkzeuge. Wenn Sie die richtigen W erkzeuge haben, wird die Installation viel einfacher .
38 © 2011 Polk Audio—all rights reserved © 2011 Polk Audio—all rights reserved 39 VERSTÄRKERANSCHLUSS Stromanschlüsse • P A D4000.4Sicherungsgröße: 2x 40AMP A TC. • Stromanschlüssemit biszu 4AWGDrahtdicke.
40 © 2011 Polk Audio—all rights reserved © 2011 Polk Audio—all rights reserved 41 8. DieserVerstärkeristauf einenLautsprecherwiderstand von2 bis8 Ohmbei Vollbereichslautsprechernundvon mindestens 4Ohm fürKanäle imBrückenmodus ausgelegt.
42 © 2011 Polk Audio—all rights reserved © 2011 Polk Audio—all rights reserved 43 PROBLEMLÖSUNGEN Symptom Mögliche Ursache Lösung Kein Sound Schwache oder fehlende Ferneinschaltung. PrüfenSiedieFerneinschaltungamV erstärker und reparieren Sie diese ggf.
44 © 2011 Polk Audio—all rights reserved © 2011 Polk Audio—all rights reserved 45 V erstärker P A D4000.4 Ty p Klasse D MOSFET , mitBrückenmodus Kanäle 4-Kanal RMS-Dauerleistung bei 4 Ohm .
46 © 2011 Polk Audio—all rights reserved © 2011 Polk Audio—all rights reserved 47 IT ALIANO INTRODUZIONE Grazieper l’acquistodi unamplificatore PolkAudio P A serieD.
48 © 2011 Polk Audio—all rights reserved © 2011 Polk Audio—all rights reserved 49 8. Selettore FRONT FULL/HPF/BPF— Permettediselezionare “nessunfiltro”, unfiltro passaalto oun filtro passa banda.
50 © 2011 Polk Audio—all rights reserved © 2011 Polk Audio—all rights reserved 51 INST ALLAZIONE DELL ’AMPLIFICA TORE Punto di installazione Il punto in cui collocare l’amplificatore dipende da numerosi fattori importanti.
52 © 2011 Polk Audio—all rights reserved © 2011 Polk Audio—all rights reserved 53 5. Se si usa un sintolettore non acquistato presso il produttore originale, girare i comandi di livello dell’amplificatore di circa un quarto di giro in senso antiorario.
54 © 2011 Polk Audio—all rights reserved © 2011 Polk Audio—all rights reserved 55 Risposta ai bassi scadente Altoparlanti cablati con la polarità sbagliata e quindi cancellazione alle basse frequenze. Controllare la polarità degli altoparlanti e correggerla se necessario.
56 © 2011 Polk Audio—all rights reserved © 2011 Polk Audio—all rights reserved 57 ÍNDICE INTRODUÇÃO ............................................................................... 57 CONTEÚDO DA EMBALAGEM ....................................
58 © 2011 Polk Audio—all rights reserved © 2011 Polk Audio—all rights reserved 59 FERRAMENT AS NECESSÁRIAS A maioria das ferramentas necessárias para realizar a instalação está descrita na lista a seguir . T er as ferramentas adequadas facilitará muito a instalação.
60 © 2011 Polk Audio—all rights reserved © 2011 Polk Audio—all rights reserved 61 CONEXÃO DOS CABOS DO AMPLIFICADOR Conexões elétricas • T amanho dosfusíveis doPAD4000.
62 © 2011 Polk Audio—all rights reserved © 2011 Polk Audio—all rights reserved 63 8. Este amplificador foi projetado para excitar uma carga de alto-falante de 2 a 8 Ω para canais que reproduzem todas as faixas de frequência e 4 Ω ,no mínimo,para canaisligados emponte.
64 © 2011 Polk Audio—all rights reserved © 2011 Polk Audio—all rights reserved 65 SUGESTÕES P ARA SOLUCIONAR PROBLEMAS Problema Provável causa Medida a ser tomada Nenhum som Acionamento remoto baixo ou inexistente. V eriqueatensãodoacionamentoremoto no amplificador e repare conforme necessário.
66 © 2011 Polk Audio—all rights reserved © 2011 Polk Audio—all rights reserved 67 Amplificador P A D4000.4 T ipo MOSFET Classe D Permite configuração em ponte Canais 4 canais Potência continua RMS a 4 Ohms 125 W x 4 Potência RMS contínua a 2 Ohm 200 W x 4 Em ponte a 4 Ohms 400 W x 2 Distorção no nível de potência nominal <0.
An important point after buying a device Polk Audio PAD4000.4 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Polk Audio PAD4000.4 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Polk Audio PAD4000.4 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Polk Audio PAD4000.4 you will learn all the available features of the product, as well as information on its operation. The information that you get Polk Audio PAD4000.4 will certainly help you make a decision on the purchase.
If you already are a holder of Polk Audio PAD4000.4, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Polk Audio PAD4000.4.
However, one of the most important roles played by the user manual is to help in solving problems with Polk Audio PAD4000.4. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Polk Audio PAD4000.4 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center