Instruction/ maintenance manual of the product FST IQ Cruiser Polaris
Go to page of 179
.
.
W ARNING Read, understand, and follow all of the in structions and sa fe ty precau tions in this manual a nd on al l product lab els. F ailure to follow the safety precautions could result in serious injury or death.
1 WELCOME Thank you for purch asing a Polaris vehicle, and welcome to our world- wide family of Polaris owners. W e proudly pro duce an exciting line of utility and recreati onal products.
2 POLARIS and POLARIS THE W A Y OUT are registered t rademarks of Pola ris Indus- tries Inc. RIDER SELECT is a trademark of Polaris Industries Inc. M-10 is a tradem ark of Fast Inc. Copyright 2006 Polaris Sales Inc. All inform ation contained within this publication is based on the latest product information at th e time of publication.
3 T A BLE OF CONTENTS Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 This section contains helpful info rmatio n for owners and drivers and illustrates the location of important identification numbers that should be recorded in the owner ’ s ma nual.
4.
5 INTRODUCTION Important Notes for Owners and Drivers After reading this manual, store it in the snowmobile for convenient ref- erence. It should remain with the snowmobile when th e snowmobile is sold. Some of the illustrations and photos used in this manual are general rep- resentations.
6 INTRODUCTION Preservation of the Environment Polaris is committed to supporting an environmental education cam- paign. W e encourage state and provin cial governments acros s the snow- belt to adopt rigorous safety traini ng programs that encourage protection of our environment, in clud ing wildlife and vegetation.
7 INTRODUCTION V ehicle Identification Numbers Record your snowmobile’ s identific ation numb ers and key nu mber in the spaces provided. Remove the spare key and store it in a safe place.
8 SAFETY Operator Safety The following signal words and symbol s appear througho ut this manual and on your veh icle. Y our safety is involved when these words and sym- bols are used.
9 SAFETY Operator Safety Follow the recommended m aintenance prog ram outlined beg inning on page 101 of this manua l to ensure that all critical components on the snowmobile are thor oughly inspected by your dealer at specific mileage intervals. WA R N I N G Driving a snowmobi le requires your ful l attention.
10 SAFETY Operator Safety Stay Clear of T rack Y our snowmobile is propelled by a rev o lving track that must be partially exposed for proper operation.
11 SAFETY Operator Safety Riding P osition Operating a snowmobile requires sk ill and balance for proper control. Rider positions may vary with expe rience; but under many conditions, the proper position is to be seated with both feet on the running boards and both hand s on the handlebar grips fo r proper throt tle, brake and steering control.
12 SAFETY Operator Safety Riding Apparel Helmet W earing a helmet can prevent a sever e head injury . Whenever riding a Polaris vehicle, always wear a helmet that meets or exceeds established safety standards. Approved helmets in the USA and Ca na da bear a U.
13 SAFETY Operator Safety Rider Capacity Driving 1-Up - Some Polaris snowmobiles are designed for a single rider only . A decal on the console of these mode ls indicates single rider operation. Driving 2-Up - Some Polaris snowmobiles ar e designed for up to two riders.
14 SAFETY Operator Safety Excessive Speed Always observe all stat e and local laws govern ing snowmobile opera- tion and speed limits. Al ways be alert and pay attention to t he trail ahead. If your speed is 40 MPH (64 km/h), your snowmobile is trav eling about 60 feet (18 m) p er second.
15 SAFETY Operator Safety Driver Awareness Slow down when traveling near poles, posts, or other obstacles. Be especially alert if you’re snowmobiling after dark. Always be on the alert for wire fences. Single strands are especially dangerous, since there may be a great distance between posts.
16 SAFETY Operator Safety Avalanches Snowmobilers should always be p roperly trained and eq uipped before traveling in mountainous terrain: • T ake an av alanch e clas s • T ravel with experienced people • T ravel on designated trails • Make sure each pers on is equipped with a shovel, probe and avalanche beacon.
17 SAFETY Operator Safety I ce and Snow Build-up Before driving, manually tu rn the skis to the left and right to be sure ice and snow are not interfering with full left and right steering. If dif ficulty is encountered, remo ve ice and snow build -up that may be obstructing the steering linkage.
18 SAFETY Operator Safety Driving on Slippery Surfaces Driving in Hilly T errain Use extra caution when operating in hi lly terrain. If climbing a hill is unavoidable, keep your weight low and forward.
19 SAFETY Operator Safety Drive Belt Do not operate the engine w i th the drive belt r emoved. Any servicing that requires operation wi thout a belt must be performed by your dealer . Operation of the engine with the belt removed may resu lt in injury or damage to the engine.
20 SAFETY Operator Safety Inadequate Snow Conditions Since snow provides the only lubr ica tion for the power slide suspension and, on liquid co oled models, coo ling for the engine, adequate snow cover is a requirement for operation of your snowmobile.
21 SAFETY Operator Safety Driving Responsibly Every snowmobile handles differently , and even the most docile condi- tions may become dangerous if operators drive improperly . If you’re new to snowmobiling, acquaint your self with the machine and with what it will and won’ t do under various conditions.
22 SAFETY Operator Safety Windchill/T emperature Charts The following informatio n is provided to help you determine when tem- peratures be come da ngerous for riding.
23 SAFETY Safety Decals and Locations W arning decals have been pl aced on the snowmobile for you r protec- tion. Read and follow the instructions of the deca ls and other warnings on the snowmobile carefully .
24 SAFETY Safety Decals and Locations “No P asseng er” W arning Snowmobiles designed for a sin- gle rider only have a warnin g decal on the left c onsole: W ARNING This vehicle is design ed for operator o nly .
25 SAFETY Safety Decals and Locations Reverse W arnin g Polaris snowmobiles equipped with el ectric reverse and will have this decal o n the cons ole: W ARNING Reverse operation, even at low speeds, can cause loss of control resulting in seri ous injury or death.
26 SAFETY Safety Decals and Locations Operation W arning An operation warning decal is pres ent on the console of all Polaris snowmobiles: W ARNING • T o avoid serious injury or death, read an d understand al l warnings and the Owne r’s Manual befor e operat ion.
27 FEA TURES 1. F ront Bum per 2. Hood 3. Headlight 4. Passenger Lumbar Adjuste r (T ouring) 5. Windshield 6. Handleba r 7. F uel Filler Cap 8. Operator Sea t 9. P assenger Se at (T ou ring) 10. P assenger Grab Handle (T ouring) 11. Grab Ha ndle Heater Switch (T ouring) 12.
28 FEA T URES 1. Rider Select t 2. Ignit ion Swit ch 3. Hand lebar hook 4. Brake Lever 5. MFD (Multi-F unction Display) 6. Engine Stop Switch 7. Throttle Control 8. Hood Hold Down Straps 9. Parking Br ake 10. Handlebar Grip W armer Switch 11. Thu mbwarmer Switc h 12.
29 FEA TURES Backrest (Cruiser) The back rest is adju stable for either operator or passenger use. See page 32 for passenger seat installation instructions. 1. Loosen the upper adjustment knobs to rais e or lower the backrest. 2. Loosen the lower adjustment knobs to move the backrest for- ward for operator use or rear- ward for passenger use.
30 FEA T URES Cargo Rack (SwitchBack) The maximum weight capacity for the cargo rack is 15 lbs. (7 kg). Always secure cargo before operating. Do not exceed the rack weight limit. Do not allow a passenger to sit on the seat back or the cargo rack. Adjustable Headlights Move the adjuster to the left to lower the headlight beam.
31 FEA TURES Storage Compartments Cargo Bag (T ouring) The carg o bag is secured to the rear of the tunnel with straps. The cargo bag and the passenger seat are removable to provide open sto rage for tr ansporting lar ger items. The maximu m weight capacity for the cargo carrier is 30 lbs.
32 FEA T URES Storage Compartments T runk/P assenger Seat/Cargo Bag (Cruiser) The trunk co ver is removable to allow installation of the passe nger seat and cargo bag. The maximum weight capacity for the cargo car- rier is 30 lbs. (14 kg). Always secure cargo before operating.
33 FEA TURES 12- V olt DC Outlet If equipped, use the ou tlet to power a global positioning sen sor (GPS), heated helmet shield, utility light, cell phone or other accessories. The 12-vo lt DC ou tlet is installed in the recoil pocket next to t he right hood hold-do wn.
34 FEA T URES RIDER SELECT Adjusta ble Steering System The RIDER SELECT adjustable steering system (if equipped) allows you to adjust the handlebar position to fit your style of riding. Some models have five (5) adjustment positions. Other models have seven (7) positions.
35 FEA TURES RIDER SELECT Adjusta ble Steering System Choosing the Best RIDER SELECT Position P osition Riding Style 1 2 3 Relaxe d T rail Ri ding Rider weight is slightly behind the center of the snowmobi le for comfortable a nd relaxed riding.
36 FEA T URES RIDER SELECT Adjusta ble Steering System 1. Stop the sn owmobile. 2. Press the releas e button and move the handlebar forward or rearward to the desired position. WA R N I N G Attempting to adjust the handlebar posi tion while the sn owmobile is moving could result in loss of control and serious injury or death.
37 FEA TURES Engine Manageme nt System Malfunction Indicator Lamp (MIL) Illuminated MIL The MIL (Check Engine Indicator) will illuminate when a problem with engine management system components is detected. 1. T urn the engine off and restart it. If the light goes off, continued operation is permissible.
38 FEA T URES Engine Manage ment System T o protect the engine, the engine management system will limit engine RPM, vehicle speed or turbo boost ( FST) if the following conditions are encountered.
39 FEA TURES Engine Manage ment System Engine Overheats (FS) Engine Overheats (FST) T urbo Boost is Limited (FST) Indication At V ehicle Speed MPH (km/h) At Engin e Te m p ° F ( ° C) Explanation Flashing High T emperature Indicator 0-31 (0-50) 230 (110) Lamp flashes when engine temperature exceeds table val- ues.
40 FEA T URES Knock Sensor (T urbo Models) A knock senso r monito rs th e engine and respo nds to detonati on by auto- matically reducing the engine timing and ad ding fuel. This results in decreased engine RPM and performance. NOTE: Engine p erformance will be red uced if fuel with a lower octa ne than 91 is used.
41 FEA TURES Instrumentation MFD Component Identification Digital Display Identification Item 1 Anal og Gaug e 2 Digital Gaug e 3 Check Engine Indicator 4 High T emp Indicato r 5 Brake Indicator 6 Rev.
42 FEA T URES Instrumentation MFD Settings The MFD control switc h allows you to set the MFD display to your pref- erences. The rocker switch has a MODE button (top) and a SET but- ton (bottom). Specif ic inst ructions are outlined on the following pages.
43 FEA TURES Instrumentation MFD Settings Speedometer/T achometer The speedometer and tachometer ca n be viewed in either the analog or the digital display . If the analog disp lay is set to show speedometer read- ings, the digital screen will automati cally display the t achometer (option 1).
44 FEA T URES Instrumentation MFD Digital Display Programs Press and release the MODE button to cycle through the three MFD pro- grams: Performance, Engine and Hist ory . Each program remains active until you cycle to the next program. While any program is active, press and release the SET button to cycl e through the program’ s screens.
45 FEA TURES Instrumentation MFD Digital Display Programs P erformance Program T r ip Settings T rip F automatically displays when the fuel level is low if the snowmobile is equipped with an electronic fuel gauge. The fuel symbol and the last fuel bar on the MFD gauge (if equipped) will blink when the fuel level reaches 1/8 of a tank.
46 FEA T URES Instrumentation MFD Digital Display Programs P erformance Program Clock Setting (if equipped) 1. Enter the Performance Program. 2. Press and release the SET button until the clock screen is active. 3. Press and hold the SET button for five seconds.
47 FEA TURES Instrumentation MFD Digital Display Programs Engine Pr ogram Press and release the MODE button until the engine program screen is active. The default display for this scr een includ es en.
48 FEA T URES Instrumentation MFD Digital Display Programs Engine Pr ogram Altitude (if equipped) The rider can calibrate th e altimeter for current atmospheric conditions . Altimeter accuracy will be +/-300 ft. (91 m) after adjustment. 1. Enter the Engine Program.
49 FEA TURES Instrumentation MFD Digital Display Programs History Program Press and release the MODE button until the history program screen is active.
50 FEA T URES Instrumentation MFD Digital Display Programs History Program Service Interval Reminder The gauge logs the number of engine hours accumulated between service reminders. When the logged hours reaches the designated service interval (set by the user), the gauge provides a reminder that service is due.
51 FEA TURES Instrumentation MFD Digital Display Programs History Program Service Interval Reminder T o r eset the r eminder at a new interval: 1. Enter th e History Program. 2. Press and release the SET button until the service interval screen is active.
52 FEA T URES Instrumentation MFD Digital Display Programs M-10 ACE Suspension Adjustments (Cruiser) A switch on the console (above the ignition switch) allows you to adjust the M-10 ACE suspension with the MFD control switch. See page 71 for instructions.
53 FEA TURES Instrumentation MFD Battery Replacement 5. Using needle-nose pliers, grasp the battery and rotate it so the lead- ing edge of the battery is raised slightly away from the battery holder . Pull the battery out gently . NOTE: The battery will not come out of t he holder un less the leading edge of the battery is raised.
54 THE PERFECT FIT IQ F ront Suspension Adjustments Independent F ront Suspension (IFS) Break in the suspension for approx imately 150 miles (240 km) before making any fine-tun ing adjustments. Settings will vary from ri der to rider , depending on rider weight, vehicle speed, riding style, an d trail conditions.
55 THE PERFECT FIT IQ F ront Suspension Adjustments Shock Damping Adjustments to the compression stif fness of ArvinMeritor MPV Select shocks can be made by turning the adjustment screw located near the base of the shock. This adjustment is the easiest to perform and it should be considered first.
56 THE PERFECT FIT IQ F ront Suspension Adjustments Shock V alving (FST IQ and FST SwitchBack only) The shocks can be revalved if spring preload alone isn't suf ficient and further adjustment is desired to control suspension stif fness.
57 THE PERFECT FIT Rear Suspension Adjustments Rider weight, riding style, trail co nditions, and vehicle speed all affect suspension action. Each rear suspension can be adjusted to suit rider preference and deliver excellent performance for a given set of conditions.
58 THE PERFECT FIT IQ & SwitchBack Rear Suspension Adjustments Initial Spring Preload Setting (Sag Method) T o set up the rear suspension torsion spring preload, measure the distance between the ground and rear bumper . This is measurement X. T ake the first measurement with no rider and with the rear sus pension at full extension.
59 THE PERFECT FIT IQ Rear Suspensi on Adjustments T orsion Spring Preload T o adjust rear torsion spring preloa d, rotate the three-position cam using the engine spark plug tool. Adjustment is easiest when the cam is rotated from low to medium, and then to high.
60 THE PERFECT FIT IQ Rear Suspensi on Adjustments Suspension Coupling On all Polaris snowmobile rear susp ensions, there are two torque arms that control the mo vement of the rail beam. Pr ior to the advent of sus- pension cou pling, these torque ar ms could move inde pendently of each other .
61 THE PERFECT FIT IQ Rear Suspensi on Adjustments Rear T o F ront Coupling and the Rear Rear Scissor Stop (RRS S) The rear rear scissor stop (RRSS) couples the movement of the rear torque arm with the front torque ar m and limits the am ount of indepen- dent moveme nt between the rear to rque and the front torq ue arm.
62 THE PERFECT FIT IQ Rear Suspensi on Adjustments W eight T ransfer During Acceleration The preferred method for controlling weight transfer during acceler ation is by adjusting the rear rear sc issor stop (RRSS). The factory setting is the best for most trail riding conditions.
63 THE PERFECT FIT SwitchBack Rear Suspension Adjustments T orsion Spring Preload T o adjust rear torsion spring preloa d, rotate the three-position cam using the engin e spark plug tool . Different rate torsion springs are available if a firmer ride is desired.
64 THE PERFECT FIT SwitchBack Rear Suspension Adjustments Rear Shock Compressi on Damping The FOX Zero Pro XC shock is stan d ard on the Swi tchBack mo del. T urn the adjustment knob on the shoc k reservoir to make adjustments to the comp ress ion damping.
65 THE PERFECT FIT F AST M-10 Rear Su spension Adjustments The M-10 suspension has been design ed to be very sensitive to rider weight. Changes in rid er weight of 25 lbs.
66 THE PERFECT FIT F AST M-10 Rear Su spension Adjustments Static Sag and Ride Height Settings 1. T o check sag, raise the rear bu mper until the suspension is fully extended (the rear shock will no t extend any further). Measure the distance from the ground to the bo ttom of the bumper (dimension X) as shown in the illustratio n.
67 THE PERFECT FIT F AST M-10 Rear Su spension Adjustments Static Sag and Ride Height Settings FRA P osition The FRA setting is the primary rear su spension adjustment . It will have the MOST ef fect on the rear suspension performance. T o adjust the FRA: 1.
68 THE PERFECT FIT F AST M-10 Rear Su spension Adjustments Static Sag and Ride Height Settings Rear Spring Preload If FRA positi on alone does not allow the setu p of the proper amount of sag, the center retainer of the rear track shock can b e replaced with optional retainers to adjust the prel oad and change the sag.
69 THE PERFECT FIT F AST M-10 Rear Su spension Adjustments Static Sag and Ride Height Settings Ski Pressure Ski pressure is set at the factory to deliver the optimum bala nce between ride and handling. If a rider prefer s more ski pressure for improved steering performance, adjustments can be made to the front limiter strap and front arm mount.
70 THE PERFECT FIT F AST M-10 Rear Su spension Adjustments Static Sag and Ride Height Settings Ski Pressure 4. The re are also two front arm mounting holes in the slide rail that can a djust ski pressure. The lower hole increases ski pressure while the upper h ole decreases ski pressure .
71 THE PERFECT FIT F AST M-10 ACE Rear Suspension Adjustments MFD Suspension Adju stments (Cruiser) A switch on the console (above the ignition switch) allows you to adjust the M- 10 ACE suspension with the MFD control switch. NOTE: The eng ine must be running to make suspension adj ust- ments with the MFD control sw itch.
72 THE PERFECT FIT Handlebar Adjustments Use the RIDER SELECT feature to adju st handlebar position. See page 34. Use the follow ing steps to adjust handlebar angle at the handlebar block. 1. Remove the handleba r cover to expose the handlebar and the four adjuster block bolts.
73 THE PERFECT FIT P assenger Grab Handle Adjustment (T ouring) On some T ouring models the position of the passenger grab handles can be adjusted for rider preference. T o make an adjustment: 1. Unscrew and remove the knob assemblies that secure the grab handles.
74 THE PERFECT FIT T raction Products Studs Before equipping yo ur snowmobile wi th traction produc ts, be awar e of the laws in yo ur area pertaining to the use of traction products.
75 THE PERFECT FIT T raction Products n Carbide Skags A skag is a replaceable bar attached to the underside of the ski to assist in turning the snowmob ile and to prevent ski wear caused by contact with roads and other bare terrain. Us e carbide skags with studded tracks to help maintai n proper vehicle steering and con trol.
76 PRE-RIDE INSPECTIONS Pre-Ride Checklist Inspect all items on th e checklist for proper operation or condition before each use of the snowmobile. Pr ocedures are outlined on the re fer- enced pages. Look for a checkmark ( n ) on the referenced pages to locate the pre-ride inspect ion items.
77 PRE-RIDE INSPECTIONS Check Before Starting the Engine Read and Un derstand Y our Owner's Manual Read the Owner's Manual completely and refer to it often. T he manual is your guide to safe an d enjoyable snowmobil ing experience. n Throttle Lever The throttle and brake are the primar y controls of your snowmobile.
78 PRE-RIDE INSPECTIONS Check Before Starting the Engine n Hood Latches The hood of the sn owmobile protects the op erator from moving parts as well as aiding in sound e mission control and other functio ns. Under no circumstances should your snowmobile be operated with the hood open or removed.
79 PRE-RIDE INSPECTIONS Check Before Starting the Engine n Brakes Always check the following items fo r proper operation before starting the engin e. Brake Lever T ravel Squeeze the brake lever . It should move no closer to the handgrip th an 1/2" (1.
80 PRE-RIDE INSPECTIONS Check Before Starting the Engine n P arking Brake Lever Lock Use the parking brake lever lock only when you wan t the snowmo- bile to remain stationary; for example, when parked on an incline for a period of five min- utes or less.
81 PRE-RIDE INSPECTIONS Check Before Starting the Engine n T rack Inspection Use of traction products such as stud s increases the possibility of track damage and/or failure. Driving at hi gh speeds for extended periods of time in mar ginal lubrication could severely damage track rods, break track edges and cause other track damage.
82 PRE-RIDE INSPECTIONS Check Before Starting the Engine n Suspension Inspection Loose nuts and bolts can reduce your snowmobile's reliability and cause needless repairs and down time. Befo re beginning any snowmobile trip, a visual inspection will uncover po tential problems.
83 PRE-RIDE INSPECTIONS Check After Starting the Engine n Engine S top Switch Check the auxiliary shut-of f switch for proper operation. Push the switch down to stop the engine . Pull it up to allow restarting. n Ignition Switch Make sure the engine stops when th e ignition switch is turned to OFF .
84 PRE-RIDE INSPECTIONS n Tip-Over Inspections In the event of a tip-over or rollover , check the oil level before operating the snowmobile. NOTE: In th e event of a tip-o ver or rollov er , the engine will stop. T o restart the engine, turn the key to the OFF position, then restart.
85 OPERA TION F uel Safety WA R N I N G Gasoline is h ighly flammable and explosive under certain conditions. • Always exercise extreme caution whene ver handling g asoline. • Always refuel outdoors or in a well-ventilated area. • Always turn off the engine before refueling .
86 OPERA TION Break-In P eriod The break-in period for your new Po laris snowmobile is the first 500 miles (800 km) of opera tion. No single action on your part is as impo r- tant as following the procedures for a proper break-in.
87 OPERA TION Starting the Engine 1. T urn the key to the ON position. 2. Pull the engine stop switc h up to the RUN position. 3. Do not apply throttle when startin g the engine unless extremely cold temperatures (below -15 ° F/-26 ° C) prevent the engine from start- ing.
88 OPERA TION Emergency Starting If the battery is too weak to start th e engine , and a battery charger is not available, the engine can be starte d using jumper cables and a charged battery from an other vehicle. Carefully read and follow the instructions on the following pages.
89 OPERA TION Emergency Starting 1. Always wear eye pr otection when jump starting your vehicle. 2. Kee p bystanders away from the vehicles. 3. Perform the emergenc y starting procedure in a well-ventilated area.
90 OPERA TION Emergency Starting 12. Make sure that the engine st op switch is in the UP position. 13. Attempt to start the vehicle. 14. If the engine does not turn over (crank over), wait 30 to 60 seconds and attempt to start the engine agai n. If the engine does not start, wait another 1 to 2 minutes and atte mpt to start the engine again.
91 OPERA TION Fu e l For peak performa nce, Polaris recomm ends the use of 91 oc tane or higher fuel. Alth ough 87 octane fuel is usable, some engine perfor- mance will be lost and fuel econ omy will decrease. Do not use lower than 87 octane fuel. Do not use fu el containing mo r e than 10% ethanol (including E85 ) .
92 OPERA TION T rack W arm-Up WA R N I N G A loose track or flying debris could caus e serious injury or death. Stand clear of the front of the ma chine and the moving track. Never ho ld the snowmobile up or stand behind it whil e warming up the track.
93 OPERA TION T rack W arm-Up Follow these steps to ensure proper warm-up of the engine, drive train and track. 1. Use an appropriate stand to securely support the rear of the snowmobile at the rear bumper . The track should be approximately 4" (10 cm) of f the ground.
94 OPERA TION n Engine Stop Switch Push down on the engine stop switch to ground ou t the ignition an d stop the engine quickly . Pull the switch up to the RUN position to allow restarting.
95 OPERA TION n Throttle Lever If the engine speed limits at 2400 RPM when the throttle lever is released: 1. T urn the ignition switch to OF F . 2. V isually inspect the throttle cabl e and throttle body to determine what caused the safety switch to activate.
96 OPERA TION Electronic Reverse (PERC 4 t ) Electronic reverse will ac tivate only when the vehicle is stopped and engine speed is below 2500 RPM. Maximum vehicle speed when oper- ating in reverse wil l be approximately 12 MPH (19 km/h). Engaging Reverse 1.
97 OPERA TION Electronic Reverse (PERC 4 t ) Disengaging Reverse 1. Stop the snowmobile and leave the engine idling. 2. Push the yellow reverse button fo r one second and release . The light on the instrument panel will shut off. 3. Apply the throttle slowly to make sure the snowmobile is in for- ward.
98 OPERA TION Daily Storage At the end of each ride, park the snowmo- bile on a level surface and supp ort it at the rear with an appropriate track stand. The track should be susp ended approximately 4" (10 cm) of f the ground. Remove the key and cover the snowmobile.
99 MAINTENANCE Emission Control Information Any qualified repair shop or qualifie d person may maintain, replace, or repair the emission control device s or systems on your snowmobile.
100 MAINTENANCE Emission Control Information Owner's Responsibilities Please read the Snowmobile Engine Emissions Limited W arranty on page 169, and read the maintenance section of your ow ner's manual.
101 MAINTENANCE P olaris Re commended Maintena nce Program T o ensure many trouble-free miles of snowmobiling enjoyment, follow recommended regular maintenance and perform service checks as out- lined in this manual. Record maintenance and service in the Mainte- nance L og beginning on page 171.
102 MAINTENANCE P eriodic Maintenance Interval T able O = Perfor m Serv ice X = Replace DAIL Y or PRE-RID E INITI ALL Y Miles (km) YEARL Y or EVERY Miles (km) Item Pg Instructions (see referenced pages) 150 (240) 500 (800) 1500 (2400) Engine Stop Switch 83 T est for proper operation.
103 MAINTENANCE P eriodic Maintenance Interval T able O = Perfor m Serv ice X = Replace DAIL Y or PRE-RID E INITI ALL Y Miles (k m) YEARL Y or EVERY Miles (km) Item Pg Instructions (see referenced pag.
104 MAINTENANCE P eriodic Maintenance Interval T able O = Perfor m Serv ice X = Replace DAIL Y or PRE-RID E INITI ALL Y Miles (km) YEARL Y or EVERY Miles (km) Item Pg Instructions (see referenced page.
105 MAINTENANCE Engine Oil Always check and change the engine oil at the intervals outlined in the Periodic Maintenance T able beginning on page 10 2. Always change the oil filter whenever changi ng oil. See page 153 fo r the part numbers of Polaris products.
106 MAINTENANCE Engine Oil n Oil Level Check NOTE: Read the entire oil check procedure b efore checking the oil level. The oil level will rise as engine temperature increases.
107 MAINTENANCE Engine Oil n Oil Level Check NOTE: The oil l evel in the oil bottle may d rain below the level of the dipstick if the engine has n ot run for more than a wee k. If you're not sure if there is oil in the system, you must first check to make sure oil is in the sys- tem before checking the oil level.
108 MAINTENANCE Engine Oil n Oil Level Check 8. Maintain the oil level in the safe oper ating range, between the upper and lower marks on the dip- stick. If the level is low , add the recommended oil in small increments, about 2 ounces (60 ml), and recheck the leve l.
109 MAINTENANCE Engine Oil Oil in System Check 1. Position the vehicle on a level su rface. Start the engine and allow it to idle 3-5 seconds (no more than 5 seconds). T urn the engine off. 2. Remove the dipstick. Clean the di pstick with a clean shop towel and reinstall it, screwing it in completely .
110 MAINTENANCE Engine Oil Oil Change Always change the oil at the interv als outlined in the Periodic Mainte- nance T able be ginning on page 102. Cle an the foam oil brea ther element with each e ngine oil c hange. Se e page 1 14. Always use the re commended oil.
111 MAINTENANCE Engine Oil Oil Change 5. Remove the oil return hose from the oil tank. H ave an as sistant place the end of the hose into a drain pan. 6. Disconnec t the 2-pin WHITE/RED and GREEN/WHITE starter motor solenoid control switch harn ess connector located near the battery .
112 MAINTENANCE Engine Oil Oil Change 18. Remove the oil fi lter cap, then remove the oil filter . Inspect the o- ring and replace it if it's worn or damaged. 19. Install a new filter , then reinstall the cap. T ighten the cap to 18.5 ft. lbs. (25 Nm).
113 MAINTENANCE Engine Oil Oil Change 25. Add additional oil to bring the le vel slightly above the lower mar k (in the safe operating range) on the dipstick. See the chart for approximate amounts to add at this step. DO NOT OVERFILL. NOTE: Check the oil level often du ring the fill procedure to avoid ove rfilling.
114 MAINTENANCE n F oam Oil Breather Elem ent The foam oil breather element abso rbs small amounts of liquid to pro- tect sensors within the intake system from damage due to oil i ngestion. Check the element before each ride. Clean or replace the breather ele- ment at each engine oil change.
115 MAINTENANCE Lubrication Driveshaft Bearing Inject grease into th e fitting on the speed- ometer sensor housing until grease pur ges from the seal on the inside of the tunnel. This should take approximately two pumps. Do not use more than four pumps.
116 MAINTENANCE Lubrication Rear Suspension Lubricate the suspension pivot shafts with Polaris Premium All Season Grease at the intervals outlined in the P eriodic Maintenance T able beginning on pa ge 102 and before seas onal storage. When opera ting in heavy , wet snow conditions, lubr icate every 500 miles (800 km).
117 MAINTENANCE Lubrication M-10 136 ACE Rear Suspension SwitchBack Rear Suspension IQ Rear Suspension + + + + + + + + + + + + + +.
118 MAINTENANCE Gearcase Oil n Gearcase Oil Check Check and change the gearcase oil at the intervals outlined in the Periodic Maintenance T able beginning on page 102. Polaris recommends the use of Polaris Synthetic Chaincase Lube. See page 153 for the part numbers of Polaris products.
119 MAINTENANCE Gearcase Oil Gearcase Oil Change The drain plug is located on the bottom of the gearcase. NOTE: Polaris does not recommend tip- ping the snowmobil e onto it's side for service. Any time the snowmo- bile is tipped onto it's left side, always check the oil leve l and clean the foam oil breather ele- ment.
120 MAINTENANCE Spark Plugs A new engine can cause temporary spar k plu g fouling due to the preser- vative added durin g the assembly process. A void prolonged idle speeds, which cause p lug fouling and carbon ization. • Use recommended sp ark plugs with the proper gap.
121 MAINTENANCE Spark Plugs Normal Spar k Plug The normal insulator tip is gray , ta n or light brown. There will be few combustion deposits. The electrodes are not burned or eroded. This indi- cates the proper type and heat range for the engine and the service.
122 MAINTENANCE Intake Filters The intake foam filter limits snow ingestion into the intake system. When operating in loos e powder snow , check the top of the foam filter periodically to remove any accumulation o f snow . F uel Injectors All fuel injector service must be performed by an au thorized Polaris dealer .
123 MAINTENANCE n Alternator Belt Inspection Inspect the alternator belt conditio n and tension before each ride. 1. Stop the en gine. 2. Op en the hood. 3. Inspect the belt for wear , cracks or other damage. If the belt is worn or damaged, install a new belt.
124 MAINTENANCE Exhaust System Check the exhaust system for wear or damage at the intervals outlined in the Periodic Maintenance T able beginning on page 102. 1. Allow the engine and ex haust system to cool completely . 2. Op en the hood. 3. Inspect the muffler and pipes for crack s or damage.
125 MAINTENANCE Cooling System Coolant The coolant supplied in the system is a 60/40 mixture of ethylene-glycol and distilled water . This mixture provi des protection again st freezing. Contact your d ealer if greater protection is requ ired. Use Premium 60/40 anti-freeze coolant, which is already premixed and ready to use.
126 MAINTENANCE Cooling System Coolant High T emperat ure Indicator Light The high temperature indicator light will illuminate when engine cool- ant temperature becomes too hot for safe continued operation of the engine. S top the snowmobile and a llow the engine to cool.
127 MAINTENANCE Cooling System Flushing the Cooling System T o ensure that the coolant maintains its ability to protect the engine, the system should be completely drained every two years and a fresh mix- ture of antifreeze and disti lled water should be added.
128 MAINTENANCE Cooling System Bleeding the Cooling System 3. Op en the hood. 4. Remove the coolant pressure cap carefully . 5. Slowly pour coolant into the filler neck until the coolant level reaches the bleed return hole on the inside of the filler neck.
129 MAINTENANCE Cooling System Bleeding the Cooling System 9. While observing the bleed return and making sure the coolant level is visible in the filler neck, observe the engine temperature in the digital display . The temperature sh ould rise steadily , indicating that the system is bleeding prop erly .
130 MAINTENANCE Drive Chain T ension Check drive chain tensio n weekly and before each long trip. T o obtain corre ct chain tension: 1. Rotate the driven clutch counterclockwise to move all chain slack to the tensioner side. Lock the brake le ver lock, or have an assistant hold the brake lever firmly .
131 MAINTENANCE Brakes n Hydraulic Brake Inspection Inspect the brake lever reserve bef ore each use of the snowmobile. See page 79. Brake pads must be replaced when the brake pad material becomes thin- ner than the backing plate, a pproximat ely 1/16" (1.
132 MAINTENANCE Brakes n Brake Fluid Replace brake fluid at least every two years with Polaris DOT 4 high tem- perature brake fluid. See page 153 for the part numbers of Polaris products. The brake fluid level can be seen through a plastic sight glass in the brake reservoir .
133 MAINTENANCE Brakes Bleeding the Hydraulic Brake System Air in the hydraulic brak e system will cause spon gy brake lever action. Bleed the system before operating the snow mobile. During the bleedin g procedure, keep the brake handle as level as possi- ble.
134 MAINTENANCE Lights Removing Halogen Bulbs NOTE: Do not touch a haloge n bulb with bare finge rs. Oil from skin leaves a residue, causin g a hot spot that will shorten the life of the lamp. If fin- gers do touch the bulb , clean it with an alcohol-moistened towel.
135 MAINTENANCE Electrical System R E LA Y LA B E L FUSE L A BEL ITEM POWERED ST ART SOLENOID REL A Y Ground side of start solenoid CHAS SIS REL A Y SP ARE 20A None ACCES SORY EMERGENCY SP ARE 30A Accessory pl ugs CHAS SIS 30A High beams Low beams Handwarmers Thum bwarmer T ail lamp Brake l amp Alternator co ils EFI REL A Y EX.
136 MAINTENANCE Clutch System Periodically inspect clutch sheaves for damage, wear or belt resi due. T o maintain optimum performance, clean with non-oil based cleaners such as isopropyl alcohol. Clutch Alignment and Offset Clutch alignment of fset is important for maintaining optimum performance.
137 MAINTENANCE Clutch System n Drive Belt Condition Periodically check the condition an d tension of the drive belt, and always carry a spare. Inspec t the belt for signs of excessive wear: frayed edges, missing cogs, cracks and exce ssive looseness.
138 MAINTENANCE Clutch System Drive Belt Removal 1. Stop the engine after operating in a forward motion. NOTE: For easier accessibility , make sure t he clutch tool access hole is visible between the 11:00 and 2:00 positions of the clutch sheave. 2. T u rn the ignit ion key of f.
139 MAINTENANCE Clutch System Drive Belt Installation 1. Drop the drive belt over the drive clutch and pull back the slack. NOTE: T o ensure satisfactory belt life, install belts so th ey operate in the same direction of rotati on by positioning the identification numbers so that you can read them.
140 MAINTENANCE T rack Replacement When replacing the track, always inst all a track having the lug size rec- ommended for your model. See your Pola ris dealer . T rack Inspection 1. Using a hoist, safely lift and sup- port the rear of the snowmobile of f the ground .
141 MAINTENANCE T rack Lubrication The slide rail requires adequate snow cover for sufficient lubrication. Excessive wear indicates insufficient lubrication. A new rail slide can cause faster heat build-up in limite d lubrication, resulting in excessive wear .
142 MAINTENANCE T rack T ension T rack adjustment is critical for prop er handling. Always maintain cor- rect tension and alignment. NOTE: T ension adjustments shou ld be made onl y after the track is warmed up and limber . 1. T urn the engine off. 2.
143 MAINTENANCE T rack T ension 4. Che ck for specified slack between th e wear surface of the track clip and the plastic rail slide. If the track needs adjustment: 5. Loosen the rea r idler shaft bolt. 6. Loosen the lock nuts. 7. T ighten or loosen the track adjus ting screws as ne cessary to provide equal adjustment on bo th sides of the track.
144 MAINTENANCE n T rack Alignment Periodically check that the track is centered and running evenly on the slide rails. Misalignment w ill cause excessive wear to the track and slide rail. 1. Safely support the rear of the snowmobile with the track of f the ground.
145 MAINTENANCE Steering System Steering Inspection and Adjustment Check all steering system fastener s weekly and before a long ride. T ighten any loose fasteners.
146 MAINTENANCE Steering System Ski Alignment W ith the handlebars in a straight ahead position, and with vehicle weight compressing the suspension, measure from the st raight edge of the skis at the center of the sk i mounting bolt.
147 MAINTENANCE Steering System n Ski Skags Check skags before each use of the snowmobile to ensu re positive steer- ing characteristics. Skags must be replaced when worn to half their orig- inal diam eter . NOTE: Carbide skags must be re placed if any a bnormal wear or chipping is found.
148 MAINTENANCE Battery Battery Removal 1. Remove the left side panel. 2. Disconnect the battery hold-down strap. 3. Disconnect the black (negative) battery cable first. 4. Disconnect the red (positive) battery cable last. 5. Lift th e battery out of the ve hicle.
149 MAINTENANCE Battery Battery Storage Whenever the vehicle is not used for a period of three months or more, remove the battery from the vehicle, ensure that it's fully char ged, and store it out of the sun in a cool, dry place. Check battery voltage each month during s torage and recha r ge as needed to maintain a full charge.
150 MAINTENANCE Battery Battery Charging For a refresh charge, follow all instructions carefully . 1. Check the battery voltage with a voltmeter or multimeter . A fully charged batt ery will register 12.8 V or higher . 2. If the voltage is less than 12.
151 MAINTENANCE Extended Storage Off-season or extended storage of your snowmobile requires preventive measures to aid against deterioration and to prolong the useful life of many compon ents.
152 MAINTENANCE Extended Storage Engine Protection Fogging the engin e is not recommen ded for this model. Electrical Connections Replace worn or frayed electrical wi re and conn ectors. Be sure wiring harness is properly sec ured away from sharp edges, steering linkage, moving parts, and hot ex haust parts.
153 POL ARIS PRODUCTS Part No. Descrip tion Engine Lu bricants 2874865 Performance Synthetic 4-Stroke (PS-4) 0W 50 Oil (qt.) 2874866 Performance Synthetic 4-Stroke (PS-4) 0W 50 Oil (gal.) Chaincase Lubr icants 2873105 Synthetic Chainc ase Lubricant (qt.
154 TROUBLESHOOTING Engine and Drive T rain T roubleshooting Engine Speed, RPM or Boost is Limited Engine Doesn't T urn Over Probable Cause Solution Engine Manageme nt System RPM Reduction Mode is activated See causes on page 38. Jammed cl utch Check for twis ted belt or broken spring.
155 TROUBLESHOOTING Engine and Drive T rain T roubleshooting Engine T urns Over , F a ils to Start Engine Backfires Probable Cause Solution Out of fuel Refuel. W ater is present in fuel See your dealer . Old or non-recommended fuel Replac e with fresh recommended fuel.
156 TROUBLESHOOTING Engine and Drive T rain T roubleshooting Engine Runs Irregularl y , Stops or Loses Power Probable Cause Solution Engine Manageme nt System RPM Reduction Mode is activated See causes on page 38. Low battery voltage R echarge the battery to 12.
157 TROUBLESHOOTING Engine and Drive T rain T roubleshooting Engine Overheating Harsh Drive Clutch Engagement Drive Belt T urns Over Drive System Noise Probable Cause Solution Inadequate snow conditions S top and c ool the engine. Drive into snow frequently to prevent overh eating.
158 TROUBLESHOOTING SwitchBack Suspension T roubleshooting Problem Solution (P erform only one change at a time) Rear suspension bottoms too easil y • V erify sag dimension (see page 58). Adjust torsion spring blocks or install optional tors ion springs to achieve correct sag dimensions.
159 TROUBLESHOOTING IQ Suspension T roubleshooting Problem Solution Rear suspension bot- toms too easily • Adjust torsion spring preload to achieve proper s tatic sag (see page 58). • Change torsion spring to stif fer optional spring (see your dealer).
160 TROUBLESHOOTING M-10 Suspension T r oubleshooting Problem Solution (P erform only one change at a time) Rear suspension bottoms too easily • Increase FRA position (see page 67). • Install appropriate opt ional center retain er on rear track shock (see page 68).
161 TROUBLESHOOTING Drive Belt W ear/Burn Cause Solution Driving a t low RPM Drive at higher RPM. Gear the machine down. Check belt deflection. Insufficient warm- up W arm the engine at least five minutes. T ake the drive belt off the machine in extremely cold weather and warm it up.
162 W ARRANTY Service And W arra nty Information Obtaining Service and W arranty Assistance Read and understand the service data and the Polaris warranty informa- tion contained in this manual. Contact your Polaris dealer for replace- ment parts, service or warra nty .
163 W ARRANTY Service And W arra nty Information P olaris Anti- Theft System The Polaris anti-theft system (P A TS) monitoring p rogram is de signed to aid owners of registered snowmobil es in recovery of stolen machines. Administration 1. Polaris snowmobile owner reports theft.
164 W ARRANTY Limited W a rranty Polaris Sales Inc., 2100 Highway 55, Me dina, MN 55340, provides a ONE YEAR LIM- ITED W ARRANTY on all components of the Po laris snowmobile ag ainst defects in material or workmanship. This warranty covers the parts and labor char ges for repair or replacement of defective parts that are cove red by this warranty .
165 W ARRANTY Limitations of wa rranties and remedies ALL IMPLIED W ARRANTIES (INCLUDING BUT NOT LIMITED TO THE IMPLIED W ARRANTIES OF MERCHANT ABILITY AND FITNESS FOR A P AR- TICULAR PURPOSE) ARE LIMITED IN DURA TION TO THE ABOVE ONE YEAR W ARRANTY PERIOD.
166 W ARRANTY Conditions and Ex clusions In order to qualify for warranty , the product must have been properly set up and tested by a Polaris Dealer (if applicable).
167 W ARRANTY P olaris Second Y ear Engine Service Contract Second Y ear Engine Service C ontract is standard on all el igible new and unused snow- mobiles that were Snow Checked through an au thorized Polaris dealer during the March/April Snow Check promot ion.
168 W ARRANTY Exported V ehicles EXCEP T WHERE SPECIFICALL Y REQUIRED BY LA W , THERE IS NO W AR- RANTY OR SER VICE BULLETIN COVERAGE ON THIS VEHICLE IF IT IS SOLD OUTSIDE THE COUNTR Y OF THE SELL ING DEALER’S AUTHORIZED LOCA- TION. This policy does not apply to vehicles that hav e received authorization for export from Polaris Industries.
169 W ARRANTY Snowmobile Engine Emis sions Limited W arranty This snowmobile engine emi ssions limited warranty is in addition to the Polaris stan- dard limited warranty for snowmobiles. Polaris Industries In c. warrants that at the time it is first purchas ed, this emissi ons-cer tified snowmobile engine meets current U.
170 W ARRANTY Snowmobile Engine Emis sions Limited W arranty Some states do not allow lim itations on how long an implied warranty lasts, so the above limitation may not apply if it is inconsistent with the controlling state law . This limited warranty excludes failures not ca used by a defect in material or workmanship.
171 MAINTENANCE L OG Present this section of your manual to your dealer each time your snow- mobile is serviced. This will provide you and future owners with an accurate log of maintenance and servi ces performed on the snowmobile. DA TE MILES (KM) TECHNICIAN SERVICE PERFORMED / COMMENTS 150 mi.
172 MAINTENANCE LOG DA TE MILES (KM) TECHNICIAN SERVICE PERFORMED / COMMENTS.
173 MAINTENANCE LOG DA TE MILES (KM) TECHNICIAN SERVICE PERFORMED / COMMENTS.
174 INDEX A Access Panel, Radi ator Compa rtment 30 Accessories . . . . . . . . . . . . . . . . . . . 73 Adjustable Steering Syste m . . . . . 34-36 Air Filte r (FST) . . . . . . . . . . . . . . . 123 Alternat or Belt Inspection . . . . . . . 123 Apparel .
175 INDEX H Handlebar A djustments. . . . . . . . . . . 72 Headlight A djusting . . . . . . . . . . . . . 30 Helmet . . . . . . . . . . . . . . . . . . . . . . . . 12 High Temperature Indicator Light . 126 Hood Latches . . . . . . . . . . . . . . . . .
176 INDEX S Storage Compartm ents. . . . . . . . . 31-32 Storage, Daily . . . . . . . . . . . . . . . . . 98 Storage, Extended . . . . . . . . . . 151-152 Studs . . . . . . . . . . . . . . . . . . . . . . . . 74 Survival Preparation . . . . . . . . . .
An important point after buying a device Polaris FST IQ Cruiser (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Polaris FST IQ Cruiser yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Polaris FST IQ Cruiser - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Polaris FST IQ Cruiser you will learn all the available features of the product, as well as information on its operation. The information that you get Polaris FST IQ Cruiser will certainly help you make a decision on the purchase.
If you already are a holder of Polaris FST IQ Cruiser, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Polaris FST IQ Cruiser.
However, one of the most important roles played by the user manual is to help in solving problems with Polaris FST IQ Cruiser. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Polaris FST IQ Cruiser along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
