Instruction/ maintenance manual of the product 700 Dragon RMK Polaris
Go to page of 135
RMK Shift 600 RMK 700 RMK 700 Dragon RMK 800 Dragon RMK Snowmobile Owner's Manual for Maintenance and Safety P antone 280 CVC.
For your nearest P olaris dealer , call 1-800-POL ARIS or visit www .polarisindustries.com Polaris Sales Inc., 2100 Hwy . 55, Medina, MN 55340 Phone 1-888-704-5290 Part No.
WARNING Read, understand, and follow all of the instructions and safety precautions in this manual and on all product labels. F ailure to fo llow the safety precautions could result in serious injury or death.
1 WELCOME Thank you for purchasin g a Polaris vehicl e, an d welcome to our world- wide family of Polaris owners. W e proudly produce an exciting line of utility and recreati onal products.
2 POLARIS and POLARIS TH E W A Y OUT are regist ered trademarks of Pola ris Indus- tries Inc. Copyright 2007 Polaris Sales Inc. All inform ation contained within this publication is based on the latest product information at th e time of publication.
3 T ABLE OF CONTENTS Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 This section contains helpful info rmation for own ers and drivers and illustrates the location of important identification numbers that should be recorded in the owner ’ s manual.
4.
5 INTRODUCTION Important Notes for Owners and Drivers After reading this manual, store it in the snowmobile for convenient ref- erence. It should remain with the snowmobile when th e snowmobile is sold. Some of the illustrations and photos used in this manual are general rep- resentations.
6 INTRODUCTION Preservation of the Environment Polaris is committed to supporting an environmental education cam- paign. W e encourage state and provin cial governments across the snow- belt to adopt rigorous safety traini ng programs that encourage protection of our environment, includ ing wildlife and vegetation.
7 INTRODUCTION V ehicle Identification Numbers Record your snowmobile’ s identific ation numbers and key nu mber in the spaces provided below . The key nu mber is stamped on the spare key . The number on the rubber -coated key is in the form of raised dots.
8 SAFETY Operator Safety The following signal words and symbol s appear throughout th is manual and on your vehicle. Y our safety is involved when these words and sym- bols are used. Become familiar with their meanings before reading the manual. The safe ty alert symbol , on your vehicle or in this manual, ale rts you to the potential for injury .
9 SAFETY Operator Safety Follow the recommended mainte nance program outlined beginning on page 71 of this manual to ensure that all critical co mponents on the snowmobile are thoroughl y inspected by your dealer at specific mileage intervals. WAR N I NG Driving a snowmobile requires your full attention.
10 SAFETY Operator Safety Stay Clear of T rack Y our snowmobile is propelled by a revo lving track that must be part ially exposed for proper operation.
11 SAFETY Operator Safety Riding Position Operating a snowmobile requires sk ill and balance for proper control. Rider positions may vary with expe rience; but under many conditions, the proper position is to be seated with both feet on the running boards and both hands on the handlebar grips for prop er throttle, brake and steering control.
12 SAFETY Operator Safety Riding Apparel Helmet W earing a helmet can prevent a sever e head injury . Whenever riding a Polaris vehicle, always wear a helmet that meets or exceeds established safety standards. Approved helmets in the USA and Ca nada bear a U.
13 SAFETY Operator Safety Disabled Operators Safe operation of this rid er-active vehicle requires good judgement and physical skills. Rider Capacity Y our Polaris snowmobile is designed for a single rider only . Do not carry a passenger . Excessive Speed Always observe all state an d local laws governing snowmobile op era- tion and speed limits.
14 SAFETY Operator Safety Driver Awareness Slow down when traveling near poles, posts, or other obstacles. Be especially alert if you’re snowmobiling after dark. Always be on the alert for wire fences. Single strands are especially dangerous, since there may be a great distance between posts.
15 SAFETY Operator Safety Avalanches Snowmobilers should always be properl y trained and equipped before traveling in mountainous terrain: • T ake an aval anche clas s • T ravel with experienced people • T ravel on designated trails • Make sure each person is equipped with a shovel, probe and avalanche beacon.
16 SAFETY Operator Safety I ce and Snow Build-up Before driving, manually tu rn the skis to the left and right to be sure ice and snow are not interfering with full left and right steering. If dif ficulty is encountered, remove ice and snow build-up that may be ob structing the steering linkage.
17 SAFETY Operator Safety Driving on Slippery Surfaces Driving in Hilly T errain Use extra caution when operating in hilly terrain. If climbing a hill is unavoidable, keep your weight low and forward.
18 SAFETY Operator Safety Drive Belt Do not operate the engine wi th the drive belt removed. Any servicing that requires operation without a belt must be performed by your dealer . Operation of the engine with the belt removed may result in injury or damage to the engine.
19 SAFETY Operator Safety Inadequate Snow Conditions Since snow provides the only lubrica tion for the power slide suspension and, on liquid cooled mo dels, coo ling for the engine, adequate snow cover is a requirement for operation of your snowmobile.
20 SAFETY Operator Safety Driving Responsibly Every snowmobile handles differently , and even the most docile con di- tions may become dangerous if oper ators drive improp erly . If you’re new to snowmobiling, acquaint your self with the machine and with what it will and won’t do under various conditions.
21 SAFETY Operator Safety Windchill/T emperature Charts The following informatio n is p r ovi ded to help yo u d et ermine when tem- peratures become da ngerous for riding.
22 SAFETY Safety Decals and Locations W arning decals have been placed on the snowmobile for your p rotec- tion. Read and follow the instructions of the deca ls and other warnings on the snowmobile carefully .
23 SAFETY Safety Decals and Locations “No P assenger” W arning Snowmobiles design ed for only a single rider have a warning de cal on the console below the steering post. WARNING This vehi cle is de signed for operator only . “NO P ASSENGER” T rack W arning The track warning decal is on the rear of the tunnel.
24 SAFETY Safety Decals and Locations Reverse Warning Polaris snowmobiles equipped with electric reverse have a reverse warning decal on th e console. WARNING Reverse operation, even at lo w speeds, can cause loss of contro l resulting in serious injury or death.
25 SAFETY Safety Decals and Locations Operation W arning (continued from previous page) • Excessive speed, especially at night or with limited visibility , can result in insuffici ent time for you to react to terrain ch anges, to avoid unexpected obstacles , or to stop safely .
26 FEA TURES 1. Fro nt Bumper (do not use for pulling or dragging the snow- mobile) 2. Hood 3. Headlight 4. Windshield 5. Mountain Bar (if equipped) 6. Handlebar 7. Seat 8. T a illights 9. Rear Bumper 10. Snow Flap 11. T rack 12. Suspension 13. T unnel 14.
27 FEA TURES 1. Fuel Filler Cap 2. Ignitio n Switch 3. MFD (Multi-F unction Display) 4. Engine Stop Switch 5. Throttle Control 6. Recoil Starter Handle 7. Hood Hold-Down Straps 8. Brake Lever 9. Parking Brake 10. Handlebar Grip Wa rmer Switch 11. Thumbwarmer Switch 12.
28 FEA TURES Adjustable Headlights Move the adjuster to the left to lower the headlight beam. Move the adjuster to the right to raise the headlight beam. Adjustable Steering The adjustable steering system allows you to adjust the handlebar position to fit your style of riding.
29 FEA TURES Detonation Elimination T echnology (DET) A detonation sensor monitors the engi ne and responds to detonatio n by automatically reducing the engine timin g and adding fuel.
30 FEA TURES Instrumentation MFD Component Identification Item 1 Analog Gauge (if equipped) 2 Digital Gauge 3 Check Engine Indicator 4 Low Oil Indicator 5 High T emp Indicator 6 Brake Indicator 7 Reve.
31 FEA TURES Instrumentation Digital Display Identification Item 1 RPM or Speed Altitude (if equipp ed) Service Interval 2 Electrical System V oltage Level 3 MAX - Maximum MPH/ KPH or RPM MPH - Miles .
32 FEA TURES Instrumentation MFD Settings The MFD Control Switch allows you to set the MFD display to your preferences. The rocker switch has a MODE button (top) and a SET button (bottom). Specific instructions are outli ned on the following pages. Standard vs.
33 FEA TURES Instrumentation MFD Digital Display Programs Press and release the MODE button to cycle through the three MFD pro- grams: Performance, Engine and History . Each progra m remains active until you cycle to the next program. While any program is active, press and release the SET button to cycl e through the program’ s screens.
34 FEA TURES Instrumentation MFD Digital Display Programs Performa nce Program T rip Settings T rip F automatically displays when the fuel level is low if the snowmobile is equipped with an electronic fuel gauge. The fuel symbol and the last fuel bar on the MFD gauge (if equipped) will blink when the fuel level reaches 1/8 of a tank.
35 FEA TURES Instrumentation MFD Digital Display Programs Engine Prog ram Air T e mper ature (accessory) The MFD displays actual air temperature. Press and hold the MODE switch for ten sec- onds to switch between standard and metric units of measurement.
36 FEA TURES Instrumentation MFD Digital Display Programs History Program Press and release the MODE button until the history program screen is active.
37 FEA TURES Instrumentation MFD Digital Display Programs History Program Service Interval Reminder The gauge log s the number of engine ho urs accumulated between service reminders. When the logged hours reaches the desig- nated service interval (set by the user), the gauge provides a reminder that service is due.
38 FEA TURES Instrumentation Gauge Cleaning 1. W ipe the gauge face as needed using a clean cloth and a mild soap and water solution. W ipe dry with clean, soft cloth. 2. Clean the back side of the gauge using a clean cloth and a mild soap and water solution.
39 THE PERFECT FIT IQ F ront Suspension Adjustments Independent F ront Suspension (IFS) Break in the suspension for approx imately 150 miles (24 0 km) before making any fine-tuning adju stm ents. Settings will vary from rider to rider , depending on rider weight, vehicle speed, riding style, and trail cond itions.
40 THE PERFECT FIT IQ F ront Suspension Adjustments W alker Evans Air Sh ocks W alker Evans Air shocks are oil filled shocks that use nitrogen pressure for spring force.These shocks are tune d for high performance riding in a wide range of winter riding conditions.
41 THE PERFECT FIT IQ F ront Suspension Adjustments Standard Shocks The tension at which the shock coil spring is set is called spring preload. For the best ride, the suspension should be adjusted to use the full travel of the shocks with occasional light bottoming.
42 THE PERFECT FIT Rear Suspension Adjustments Rider weight, riding style, trail co nditions, and vehicle speed all af fect suspension action. Each rear suspension can be adjusted to suit rider preference and deliver excellent performance for a given set of conditions.
43 THE PERFECT FIT Rear Suspension Adjustments Initial Spring Preload Setting (Sag Method) T o set up the rear suspension torsion spring preload, measure the distance between the ground and rear bumper . This is measurement X. T ake this measurement with no rider and with the rear suspension at full extension.
44 THE PERFECT FIT Rear Suspension Adjustments T orsion Spring Preload T o adjust rear torsion spring preloa d, rotate the three-position cam using the engine spark plu g t ool . Dif ferent rate torsion springs are available if a firmer ride is desired.
45 THE PERFECT FIT Rear Suspension Adjustments Shock Compres sion V alving RMK Standard Rear T rack Shock The standard RMK rear track shock is an Arvin MPV Select shock that allows for adjustments to the compression valving. Adjustments are made by turning the adjustment scr ew located near the base of the shock.
46 THE PERFECT FIT Handlebar Adjustments Handlebar position and handlebar angle can be adjusted to rider prefer- ence. The optimum position for the prop er vehicle balance is with the riser block aligned with th e steering post. After making handlebar adjustments, check to make sure wires are not pinched or kinked.
47 THE PERFECT FIT Handlebar Adjustments Handlebar Position 1. Loosen the four bolts on the bottom of the adjuster block. NOTE: If necessary , pry the blocks apart with a screwdr iver . 2. Adjust the handlebar forward or rearward to the desired position.
48 THE PERFECT FIT Accessories Polaris offers a wide range of accesso ries for your snowmobile to help make each ride more enjoyable. Use only Polaris parts and accessorie s on your Polaris snowmobile.
49 PRE-RIDE INSPECTIONS Pre-Ride Checklist Inspect all items on th e checklist for proper operation or condition before each use of the snowmobile. Pr ocedures are outlined on the refer- enced pages. Look for a checkmark ( n ) on the referenced pages to locate the pre-ride inspection items.
50 PRE-RIDE INSPECTIONS Before Starting the Engine Before starting the engine, always re fer to all safety warnings pertaining to snowmobile operation.
51 PRE-RIDE INSPECTIONS Before Starting the Engine n Recoil Rope Inspect the recoil rope and handle fo r exces sive wear , and make sure the knot securing the rope inside the ha ndle is secure. If excessive wear is found, see your Polaris dealer for replacement.
52 PRE-RIDE INSPECTIONS Before Starting the Engine n P arking Brake Lever Lock Use the parking brake lever lock only when you want th e snowmobile to remain stationa ry; for example, when parked on an incline for a period of five minutes or les s. 1. Brake Lever 2.
53 PRE-RIDE INSPECTIONS Before Starting the Engine n Steering System Manually turn the skis completely to the right and to the left . If any dif- ficulty is encountered , remove any ice and snow build -up that may be obstructing the steering linkage.
54 PRE-RIDE INSPECTIONS Before Starting the Engine n Suspension Inspection Loose nuts and bolts can reduce your snowmobile's reliability and cause needless repairs and down time. Befo re beginning any snowmobile trip, a visual inspection will uncover po tential problems.
55 PRE-RIDE INSPECTIONS Start the Engine and Check Before starting the engine, always re fer to all safety warnings pertaining to snowmobile operation. Never en gage the starter wh en the engine i s running. Never start the engine with out checking all ve hicle components to be sure of proper operation.
56 OPERA TION Starting the Engine 1. T urn the key to the ON position. Pull the engine stop switch up to the RUN position. 2. Carbureted models: Tu r n the fuel valve on. If starting a cold engine, flip the choke toggle to FULL CHOKE. Do not use the choke if starting a warm engine.
57 OPERA TION Engine Break-In No single action on your part is as important to long, trouble-free machine life as proper break-in of a new or rebuilt engine. Premix the first tank of gasoline with one p int of Polaris injection oil for each five gallons of fuel.
58 OPERA TION Engine Break-In Oil Injection System Always fill the oil reservoir when refueling. Oil Recommendations This snowmobile is equipped with a variab le exhaust sys tem (VES). Engine lubrication comes from oil ad ded to the fuel and oil injection systems.
59 OPERA TION T rack W arm-Up Follow these steps to ensure proper warm-up of the engine, drive train and track. 1. Use an appropriate stand to securely support the rear of the snowmobile at the rear bumper . The track should be approximately 4" (10 cm) of f the ground.
60 OPERA TION F uel Safety WAR N I NG Gasoline is h ighly flammable and explosive under certain conditions. • Always exercise extreme caution w henever handling gasoline. • Always refuel outdoors or in a well-ventilated area. • Always turn off the engine before refueling.
61 OPERA TION Fu e l For peak performance, Po laris recommends the use of 91 octane or higher fuel. Although 87 octane fuel is usable, some engine perfo r- mance will be lost and fuel econ omy will decrease. Do not use lower than 87 octane fuel. Do not use fuel containing mor e than 10% eth anol (including E85) .
62 OPERA TION Oil n Low Oil Indicator Light The low oil indicator light will alert th e operator if the oil level is low . V isually check for oil in the bottle. Add oil before further operation of the snowmobile. See page 58 for oi l recommendations.
63 OPERA TION n Engine Stop Switch Push down on the engine stop switch to ground out the ignition and stop the engine quickly . Pull the switch up to the RUN position to allow restarting.
64 OPERA TION n Throttle Lever If the engine stops abruptly when the throttle lever is released: 1. T urn the ignition switch to OFF . 2. V isually inspect the throttle cabl e and throttle body to determine what caused the safety switch to activate. 3.
65 OPERA TION n Emergency Stoppi ng The following chart lists methods for stopping the snowmobile in the event of an emergency . See page 63 for more information about the engine stop switch.
66 OPERA TION Electronic Reverse (PERC t ) Electronic reverse will activate only if the engine RPM is below 4000. The maximum engine RPM will be 6000 when in reverse. WAR N I NG Improper reverse operation, even at low speeds, may cause loss of control, resulting in serious injury or death.
67 OPERA TION Electronic Reverse (PERC t ) Engaging Reverse 1. S top the snowmobile and leave the engine idling. 2. Make sure the area behind yo ur snow- mobile is clear . 3. Push the yellow reverse button on the left-hand control fo r one second, then release.
68 OPERA TION Daily Storage At the end of each ride, park the snowmobile on a level surface and support it at the rear with an appropriate track stand. The track should be suspended approximately 4" (10 cm) of f the ground. Remove the key and cover the snowmobile.
69 MAINTENANCE Emission Control Information Any qualified repair shop or qualifie d person may maintain, replace, or repair the emission control device s or systems on your snowmobile.
70 MAINTENANCE Emission Control Information Owner's Responsibilities Please read the Snowmobile Engine Emissions Limited W arranty on page 125, and read th e maintenance section of your owner's manual.
71 MAINTENANCE P olaris Recommended Mai ntenance Program T o ensure many trouble-free miles of snowmobiling enjoyment, follow recommended regular maintenance and perform se rvice checks as out- lined in this manual. Record maintenance and service in the Mainte- nance Log begin ning on page 127.
72 MAINTENANCE P eriodic Maintenance Interval T able The following chart is a guide based on average riding conditions. Y o u may need to increase frequency based on ri ding conditions. When inspection reveals the need for replacement parts , always use genuine Polaris parts, available from your Polaris dealer.
73 MAINTENANCE P eriodic Maintenance Interval T able Item See Pag e Fr equency 150 mi. (240 km) 500 mi. (800 km) 1000 mi. (1600 km) 2000 mi. (3200 km) Pre- Season BRAKES Hose Routing -- II II Hose Con.
74 MAINTENANCE P eriodic Maintenance Interval T able I - Inspect (clean, adjust, tighten, lubricate, replace if necessar y) C - Clean R - Replace L - Lubricate Item See Pag e Fr eq u e nc y 150 mi. (240 km) 500 mi. (800 km) 1000 mi. (1600 km) 2000 mi.
75 MAINTENANCE Lubrication F ront Suspension The front suspension does not require lubrication. Rear Suspension Lubricate the suspension pivot shafts with Polaris Pr emium All Season Grease at the intervals outlined in the Periodic Maintenance T able beginning on page 72 and before sea sonal storage.
76 MAINTENANCE Lubrication Driveshaft Bearing Inject grease into th e fitting on the speed- ometer sensor housing until grease pur ges from the seal on the inside of the tunnel. This should take approximately two pumps. Do not use more than four pumps.
77 MAINTENANCE Lubrication n Chaincase Oil Check the chaincase oil leve l at the intervals outlined in the maintenance charts beginning on page 71 . The sigh t glass is located on th e lower rear of the chaincase. Maintain the oil level at or slightly below the center of the sight glass.
78 MAINTENANCE Lubrication Chaincase Oil Oil Change 1. Position the vehicle on a level surface. 2. Remove the drain plug and drain the oil into a drain pan. Allow the oil to drain completely . 3. Clean off all metal shavings from the plug. 4. Install a new sealing washer on the drain plug.
79 MAINTENANCE Spark Plugs Spark plug condition is indicative of engine operation. The spark plug firing end condition should be read after the engine has been warmed up and the vehicle has been driven at higher spe eds. Immediately check the spark plug for correct color .
80 MAINTENANCE Spark Plugs A new engine can cause temporary spar k plug fouling du e to the preser- vative added during the assembly p rocess. A void prolonged idle speeds, which cause plu g fouling and carbon ization. Change the spark plugs every 2000-2500 miles (32 00-4000 km).
81 MAINTENANCE Intake Filters The intake foam filter limits snow ingestion into the intake system. When operating in loose powder snow , check the top of the foam filter periodically to remove any accumulat ion of snow . CA UTION Operatin g the snowmobile with the intake filters removed may cause intake icing.
82 MAINTENANCE F uel Injectors (F uel Injected Models) All fuel injector service must be performed by an au thorized Polaris dealer . Do not attempt to clean or service the fuel injectors. Fu e l P u m p All fuel pump service must be pe rformed by an authorized Polaris dealer .
83 MAINTENANCE Carburetor (Carbureted Models) The number stamped in the end of the main jet indicates the jet size. The jet installed at the time of manufacture is not necessarily correc t for your elevation. It's your dealer's responsi bility to make sure the correct main jet is installed.
84 MAINTENANCE Carburetor (Carbureted Models) Carburetor W ater/Sediment T rap Most Polaris snowmobiles contain pa tented carburetor bowl water/sedi- ment traps located at the bottom of each carburetor . The trap, consisting of a hose with a plug, should be drained about every 1000 miles (1600 km) and inspected for contamination.
85 MAINTENANCE Exhaust System Check the exhaust system for wear or damage at the intervals outlined in the Periodic Maintenance T able beginning on page 71. Always allow the engine and exhaust system to cool co mpletely before inspecting. 1. Open the hood and inspect the mu ffler and pipes for cracks or dam- age.
86 MAINTENANCE Cooling System Coolant The coolant supplied in the system is a 60/40 mixture of ethylene-gly col and distilled water . This mixture provi des protection agains t freezing. Contact your dealer if greater protection is required. Use Premium 60/40 anti-freeze coolant, which is already premixed and ready to use.
87 MAINTENANCE Cooling System Coolant High T emperat ure Indicator Light The high temperature indicator light wi ll illuminate when engine cool- ant temperature becomes too hot for safe continued operation of the engine.
88 MAINTENANCE Cooling System Bleeding the Cooling System Use of a non-standard pressure cap will not allow the recovery system to function properly . If the pressure cap needs repla cement, contact your dealer for the correct part. WAR N I NG Steam and hot liquids will cause serious burns to your skin.
89 MAINTENANCE Cooling System Bleeding the Cooling System Bleed the cooling system at the intervals outlined in the Periodic Main- tenance T ab le beginning on page 72. Perform the bleeding procedure when the engine is cold. 1. Remove the pressure cap and fill the coolant bottle with properly mixed coolant to the maximum mark.
90 MAINTENANCE Drive Chain T e nsion Check drive chain tension weekly and before each long trip. T o obtain correct chai n tension: 1. Rotate the driven clutch counterclockwise to move all chain slack to the tensioner side. Lock the brake lever lock, or have an assistant hold the brake lever firmly .
91 MAINTENANCE Brakes n Hydraulic Brake Inspection Inspect the brake lever travel before eac h use of the snowmobile. See page 51. Brake pads must be replaced when the brake pad material becomes thin- ner than the backing plate, approximately 1/16" (1.
92 MAINTENANCE Brakes Brake Components •B r a k e D i s c • Bleed Screw •B r a k e L i n e • Brake Caliper • Brake Pad Material - Replace when thickness is less than 1/16" (1.
93 MAINTENANCE Brakes n Brake Fluid Replace brake fluid at least every two years with Polaris DOT 4 high tem- perature brake fluid. See page 1 12 for the part numbers of Polaris products. The brake fluid level can be seen through a plastic sight glass in the brake reservoir .
94 MAINTENANCE Brakes Bleeding the Hydraulic Brake System Air in the hydraulic brak e system will cause spon gy brake lever action. Bleed the system before operating the snowmobile. During the bleeding proc edure, keep the brake handle as level as po ssi- ble.
95 MAINTENANCE Lights Removing Halogen Bulbs NOTE: Do not touch a halogen bul b with bare fingers. Oil from skin leaves a residue, causing a hot sp ot that will shorten the life of the lamp. If fin- gers do touch the bulb, clean it wi th an alcohol-moistened towel.
96 MAINTENANCE Clutch System Periodically inspect clutch sheaves for damage, wear or belt residue. T o maintain optimum performance, clean with non-oil based cleaners such as isopropyl alcohol. Clutch Alignment Offset Clutch alignment offset i s import ant for maintaining optimum perfor- mance.
97 MAINTENANCE Clutch System n Drive Belt Condition Belt width and length must match the center distance of the clutches and sheave width of the drive clutch. For this reason, Polaris recommends that only O.E.M. belts be used. Ot her belts may match the dimensions, but can drastically change the shif t pattern, resulting in poor perfor- mance.
98 MAINTENANCE Clutch System Drive Belt Removal 1. S top the engine after operating in a forward motion. NOTE: For easier accessibility , make sure t he clutch tool access hole is visible between the 11:00 and 2:00 positions of the clutch sheave. 2. Turn the ig nition key of f.
99 MAINTENANCE Clutch System n Drive Belt Deflection Measure belt deflection with both clutches at rest and in their full neutral position. Place a straight edge on the belt and apply downward pressure while measuring at point A. This measurement should b e 1 1/4" (3.
100 MAINTENANCE T rack Replacement When replacing the track, always inst all a track having the lug size rec- ommended for your mo del. See your Polaris dealer . T rack Inspection 1. Using a hoist, safely lift and sup- port the rear of the snowmobile of f the ground.
101 MAINTENANCE T rack Lubrication The slide rail requires adequate snow cover for suf ficient lubrication. Excessive wear indicates insufficient lubrication. A new rail slide can cause faster heat build-up in limite d lubrication, resulting in excessive wear .
102 MAINTENANCE T rack T ension T rack tension is critical for maxi mum efficiency and performance. T rack tension controls the approach angl e of the track to the rail beam in powder snow conditions. Deep snow performance will be optimized at the specified tension.
103 MAINTENANCE T rack T ension If the track needs adjustment: 5. Loosen the rear idler shaft bolt. 6. Loosen the lock nuts. 7. T ighten or loosen the track adjus ting screws as necessary to provide equal adjustment on bo th sides of the track. 8. Repeat the measuremen t on the other side of the track.
104 MAINTENANCE n T rack Alignment Periodically check that the track is centered and running ev enly on the slide rails. Misalignment will cause excessive wear to the track and slide rail. 1. Safely support the rear of the snowmobile with the track off the ground.
105 MAINTENANCE Steering System Steering Inspection and Adjustment Check all steering system fa stener s week ly and before a long ride. T ighten any loose fasteners.
106 MAINTENANCE Steering System Ski Alignment W ith the handlebars in a straight ahead position, and with vehicle weight compressing the suspension, measure from the straight e dge of the skis at the center of the sk i mounting bolt.
107 MAINTENANCE Steering System n Ski Skags Check skags before each use of the snowmobile to ensu re positive steer- ing characteristics. Skags must be replaced when worn to half their orig- inal diameter . NOTE: Carbide skag s must be replaced if a ny abnormal wear or ch ipping is found.
108 MAINTENANCE Steering System n Rail Slide Wear For ease of inspection, all Polaris rail slides have a wear limit indicator groove to indicate the minimum permissible slide thick- ness. Replace the rail slides if they are worn to the top of the groove at any point along their length.
109 MAINTENANCE Extended Storage Off-season or extended storage of your snowmobile requires preventive measures to aid against deterioration and to prolong the useful life of many componen ts.
110 MAINTENANCE Extended Storage Engine and Carburetor Prot ection (Carbureted Models) Proper preparation of the engine and fuel system is vital to the preven- tion of rust an d corrosion on precisio n engine parts during storage. Whenever the machine is stored for a period of more than 60 days, the engine must be fogged with foggi ng oil.
111 MAINTENANCE Extended Storage Electrical Connections Replace worn or frayed electrical wi re and connec tors. Be sure wiring harness is properly secured awa y from sha r p edges, steering linkage, moving parts, and hot exhaust pa rts. T rack and Suspension Moderate track tension should be ma intained during summer storage.
112 POL A RIS PRODUCTS Pa r t N o . Description Engine Lubrica nts 2870791 Fogging Oil (12 oz. Aerosol) 2871098 Premium 2-Cycle Engine Oil (qt.) 2871097 Premium 2-Cycle Engine Oil (gal.) 2871240 Premium 2-Cycle Engine Oil (2.5 gal.) 2871721 Premium Gold Synthetic 2-Cycle Engine Oil (qt.
113 TROUBLESHOOTING Engine T roubleshooting Unless you have experience and traini ng in two-cycle engine repair , see your dealer if technical problems arise. Problem Probable Ca use Solution Erratic engine oper- ating RPM during acceleration o r load variations Drive clutch binding • SEE YOUR DEALER.
114 TROUBLESHOOTING Engine T roubleshooting Problem Probable Ca use Solution Noise in drive sys- tem Broken drive clutch components • S EE YOUR DEALER. Bearing failure/ chaincase, jacks haft, or front drive shaft • S EE YOUR DEALER. Drive belt surface flat spots • Inspect and replace as needed.
115 TROUBLESHOOTING Engine T roubleshooting Problem Probable Ca use Solution Engine turns but fails to start Faulty ignition • Install new spark plug(s). If engine still fails to start, check f or spark. If there's no spark, SEE YOUR DEALER. No fuel to engine • Make sure the fuel valve is on.
116 TROUBLESHOOTING Suspension T roubleshooting Problem Solution Rear suspension bot- toms too easily • Set static sag (see page 43). Adjust torsion spring blocks or install optional torsion spri ngs to achieve correct sag dimensions. Rides too stiff in rear • Check for bindi ng suspension components and grease all pivot points.
117 TROUBLESHOOTING Drive Belt T roubleshooting Belt W ear/Burn Diagnosis Causes Solutions Driving at low RPM • Driv e at higher RPM. Gea r the ma chi ne down. Check belt deflection. Insufficient warm-up • W arm the engine at least five minutes. T ake the drive belt off the ma chi ne in extremely cold weather and warm it up.
118 W ARRANTY Service And W arra nty Information Obtaining Service and W arranty Assistance Read and understand the service data and the Polaris warranty informa- tion contained in this manual. Contact your Polaris dealer for replace- ment parts, service or warranty .
119 WA RRANTY Service And W arra nty Information Polaris Anti- T heft System The Polaris anti-theft system (P A TS) monitoring program is designed to aid owners of registered snowmobil es in recovery of stolen machines. Administration 1. Polaris snowmobile owner reports theft.
120 W ARRANTY Limited W a rranty Polaris Sales Inc., 2100 Highway 55, Me dina, MN 55340, provides a ONE YEAR LIM- ITED W ARRANTY on all components of the Po laris snowmobile ag ainst defects in material or workmans hip.
121 WA RRANTY Limitations of warranties and remedies ALL IMPLIED W ARRANTIES (INCLUDING BUT NOT LIMITED TO THE IMPLIED W A RRANTIES OF MERCHANT ABILITY AND FITNESS FOR A P AR- TICULAR PURPOSE) ARE LIMITED IN DURA TION TO THE ABOVE ONE YEAR W ARRANTY PERIOD.
122 W ARRANTY Conditions and Exclusions In order to qualify for warranty , the product must have been properly set up and tested by a Polaris Dealer (if applicable).
123 WA RRANTY Polaris Second Y ear Engine Service Contract Second Y e ar Engine Service C ontract is standard on all el igible new and unused snow- mobiles that were Snow Checked through an au thorized Polaris dealer during the March/April Snow Check promot ion.
124 W ARRANTY Exported V ehicles EXCEP T WHERE SPECIFICALL Y REQUIRED BY LA W , THERE IS NO W AR- RANTY OR SER VICE BULLETIN COVERAGE ON THIS VEHICLE IF IT IS SOLD OUTSIDE THE COUNTR Y OF THE SELL ING DEA LER’S AUTHORIZED LOCA- TION. This policy does not apply to vehicles that have received authorization for export from Polaris Industries.
125 WA RRANTY Snowmobile Engine Emis sions Limited W arranty This snowmobile engine emi ssions limited warranty is in addition to the Polaris stan- dard limited warrant y for sn owmobiles.
126 W ARRANTY Snowmobile Engine Emis sions Limited W arranty Some states do not allow lim itations on how long an implied warranty lasts, so the above limitation may not appl y if it is incon sistent with the controlling sta te la w . This limited warranty excludes failures not ca used by a defect in material or workmanship.
127 MAINTENANCE L OG Present this section of your manual to your dealer each time your snow- mobile is serviced. This will provide you and future owners wit h an accurate log of maintenance and servi ces performed on the snowmobile. DA TE MILES (KM) TECHNICIAN SERVICE PERFORMED / COMMENTS 150 mi.
128 MAINTENANCE LOG DA TE MILES (KM) TECHNICIAN SERVICE PERFORMED / COMMENTS.
129 MAINTENANCE LOG DA TE MILES (KM) TECHNICIAN SERVICE PERFORMED / COMMENTS.
130 INDEX A Accessories . . . . . . . . . . . . . . . . . . . 48 Apparel for Riding . . . . . . . . . . . . . . 12 Avalanches . . . . . . . . . . . . . . . . . . . . 15 B Brake Components. . . . . . . . . . . . . . 92 Brake Fluid . . . . . . . . . . .
131 INDEX H Handlebar Adjustments. . . . . . . . 46-47 Handlebar Angle . . . . . . . . . . . . . . . . 47 Handlebar Po sition . . . . . . . . . . . . . . 47 Headlight Adjus tments . . . . . . . . . . . 28 Helmet Recomm endations . . . . . . . . 12 Hood Latches .
132 INDEX S Snow Build-up . . . . . . . . . . . . . . . . . 16 Snow Conditions . . . . . . . . . . . . . . . 19 Spark Plugs . . . . . . . . . . . . . . . . . 79-80 Speed . . . . . . . . . . . . . . . . . . . . . . . . 13 Spring Preload . . . . . . . .
An important point after buying a device Polaris 700 Dragon RMK (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Polaris 700 Dragon RMK yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Polaris 700 Dragon RMK - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Polaris 700 Dragon RMK you will learn all the available features of the product, as well as information on its operation. The information that you get Polaris 700 Dragon RMK will certainly help you make a decision on the purchase.
If you already are a holder of Polaris 700 Dragon RMK, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Polaris 700 Dragon RMK.
However, one of the most important roles played by the user manual is to help in solving problems with Polaris 700 Dragon RMK. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Polaris 700 Dragon RMK along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
