Instruction/ maintenance manual of the product 50-0230B-004 Plantronics
Go to page of 8
INSTALLATION INSTRUCTIONS FOR 50 - 0230B - 002 50 - 0230B - 003 50 - 0230B - 004 SUBURBAN Overhead console with flip down TV These instructions are intended for use only by experienced professionals in the automotive customizing business.
2 MATERIALS PROVIDED FOR INSTALLATION: ITEM Description QTY 1 SCREW, # 8 X 3/4" HWH 4 2 SCREW, # 6 X 1/2" PPH 4 3 SCREW, # 6 X 3/8" PPH 4 4 SCREW, # 8 X 2 1/2" PFH 3 5 SCREW, #8 X .
3 I. PREPARATION OF VEHICLE I NTERIOR 1. Remove the O.E.M. console mounted to inner roof of vehicle. Remove and discard (1) one screw from recess in front of console near rear view mirror. Disconnect wire harness and remove console from vehicle. Use care not to damage A/C control head.
4 6. Carefully trim headliner from the dome light area toward the front of vehicle as shown. See figure 4. Caution: Bef ore cutting headliner material, check for wiring or other componentry above headliner. Cut only where indicated. 7. Install the mounting bracket in the O.
5 9. If vehicle is equipped with an elect ronic compass, unsnap the wire harness clip and relocate toward center of vehicle. See Figure 7. 10. Remove and retain the (2) two door scuff plates on driver’s side. See Figure 8. 11. Remove and retain the handle which mou nts to the top of the “B” pillar.
6 13. Measure 7” from rear A/C control opening toward the rear of vehicle. Using a razor knife, carefully cut an opening in the headliner that is 6” wide x 8 3/4” long. Make sure that the 6” width is centered in the vehicle. Caution: Before cutting headliner material, check for wiring or other componentry above headliner.
7 19. Install and route all video and audio cables, and any other added component re quirements to their respective places in the vehicle. Refer to component installation instructions for wiring diagrams. The suggested routing of the video system cable is as follows: Above the headliner from rear A/C switch opening to B - pillar.
8 25. Raise video system into approximate position and connect all wiring to components. Route video c able through hole in mounting bracket. Connect wiring and cabling to video system per instructions included with video system. Make sure lights in video system operate with door jamb switch.
An important point after buying a device Plantronics 50-0230B-004 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Plantronics 50-0230B-004 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Plantronics 50-0230B-004 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Plantronics 50-0230B-004 you will learn all the available features of the product, as well as information on its operation. The information that you get Plantronics 50-0230B-004 will certainly help you make a decision on the purchase.
If you already are a holder of Plantronics 50-0230B-004, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Plantronics 50-0230B-004.
However, one of the most important roles played by the user manual is to help in solving problems with Plantronics 50-0230B-004. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Plantronics 50-0230B-004 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
