Instruction/ maintenance manual of the product ADE-3410v2 Planet Technology
Go to page of 62
ADSL 2/2+ Router with USB Port ADE-3410v2 User's Manual.
Copyright Copyright © 2007 by PLANET Technology Corp. All rights reserved. No part of this publication may be reproduced, transmitt ed, transcribed, stored in a retrieval system, or translated into a.
R&TTE Compliance Statement This equipment complies with all the requirements of DIRE CTIVE 1999/5/EC OF THE EUROPEAN PARLIAMENT AND THE COUNCIL OF 9 March 1999 on radio equipment and telecommunica.
4 Table of Contents 1. Intro duction ................................................................................................. 6 1.1 Features.......................................................................................... 6 1.2 Package Contents .
3.5.2 LA N .................................................................................... 36 3.5.3 NAT .................................................................................... 37 3.5.4 Secu rity ......................................
1. Intr oduction The PLANET ADSL 2/2+ Router, ADE-3410v2, provi des office and residential users the ideal solution for sharing a high-speed ADSL 2/2+ broadband Internet connection on one Ethernet port and one USB port. It can s upport downstream transmission rates of up to 24Mbps and upstream transmission rates of up to 3.
VPN Pass through Support PCs with VPN (Virtual Private Networking) software using PPTP, L2TP, and IPSec are transparently supported - no configuration is required. RIP Routing It supports RIP routing protocol for routing capability. Simple Network Management Protocol (SNMP) It is an easy way to remotely manage the router via SNMP.
LED Indicator LED Meaning 1 PWR Lit when power is ON. 2 Link Lit when DSL line is connected. Blink when DSL line is training. 3 Data Blink when DSL data is transferring. 4 LAN Lit when connected to an Ethern et device. Blink when data is Transmitted / Received.
Rear panel Port and Button Definition Port Meaning 1 Power Switch Power ON/OFF switch 2 Power Connect the supplied power adapte r to this jack (10 DC, 1A). 3 Reset After the device is powered on, press it to reset the device or restore to factory default settings.
3. 64 MB RAM minimum 4. 20 MB of free disk space minimum 5. Ethernet Network Interface Card 2.2 Hardwar e Installati on This section describes how to connect and configure the ADE-3410v2. The DSL router may connect to a PC’s USB or Ethernet. D SL router will support at least one of connectivity methods.
USB Installation To connect the DSL router to the PC ’s USB port, perform the following: z Connect the USB cable to the USB port on the DSL router. The cable has two different connectors; you may ha ve to try both connectors. z Connect the other end of the USB cable into the PC’s USB port.
2.4 Factory Reset Button The Router may be reset to the original f actory default settings by depressing the reset button for a few seconds while the device is powered on.
the windows will search CD-Rom for the best USB driver. . The dialog prompted you to choose your se arch and installation options. You can choose the path of USB drive installation.
Click the button<Finish> to comple te the USB driver installation. 3. Intr oduction to WEB Configuration 3.1 Quick Setup The Quick Setup allows the user to confi gure the ADSL router for DSL connectivity and Internet access. It also guides the user though the WAN network setup first and then the LAN interface setup.
ADE-3410V2 also supports pass-through PPPo E sessions from the LAN side while simultaneously running a PPPoE client fro non-PPPoE LAN devices. NAPT and firewall are always enabled when PPPoE mode is s.
STEP 4: Click Next to display the following screen. C hoosing different connection types pops up different settings requests. Enter appr opriate settings that are requested by your service provider. The following descriptions state each connection type setup separately.
using the LAN interface IP address. The ADSL r outer exten d s the IP su bnet at the remote service provider to the LAN PC. That is, th e PC becomes a host belonging to the same IP subnet. The ADSL router bridges the IP packets between WAN and LAN ports, unless the packet is addressed to the router’s LAN IP address.
5. After clicking Save/Reboot , the router will save the conf iguration to the flash memory, and reboot. The Web UI will not respond until the system is brought up again. After the system is up, the Web UI will refres h to the Device Info page autom atically.
After logging in the ROUTER by a super username, you can query, configure, and modify all configurations of the ROUTER ; and you can diagnose the ROUTER system too. You need to reboot the ROUTER to enable your modification or c onfiguration effective sometimes, e.
This interface contains the following information: Board ID: Software Version: Bootloader (CFE) Version: Upstream Line Rate/Downstream Line Rate LAN IP Address: The management IP address Default Gateway: No gateway in a pure bridging mode; under other m odes such as PPPOE/PPPOA, it is the address of the uplink equipment.
3.4.3 S tatistics -- LAN Click “Statistics”-->”L AN” to show the fo llowing interface. You can query infor mation on packets received at the Ethernet, USB and Wireless interfaces. Click “Reset Statistics” to return the valu es to zero and recount them.
3.4.5 S tatistics -- A TM Click “Statistics”-->”ATM” to show the fo llowing interface. You can query information on packets received at the ATM interfaces. Click “Reset” to return the values to zero and recount them. 3.4.6 S tatistics -- ADSL Click “Statistics”-->”ADSL” to show the following interface.
You will see the following inf ormation per tinent to the ADSL line in the p age: Mode: G.DMT/G.LITE/T1.413/ADS L 2+/ADSL 2/READSL2 Line Coding: Trallis on, etc. Status: Link Down, No Defect, Training Link Power State: L0, L1, L2 Rate (Kbps): Upstream Line Rate/Downstream Line Rate.
3.4.8 ARP Click “ARP” to show the following interface. You can query the MAC and IP addresses information of the equip ment attached to the ROUTER. 3.4.9 DHCP Click “DHCP” to show the following interface. You can query the IP addresses assignment from the DHCP server.
3.5 Advanced Setup Click “Advanced Setup” to enter the advanced system setup interface. By default, there are two options at the left side of the interface: “WAN”, “LAN”, etc.
Choose Add, Edit, or Remove to configure WAN interfaces. Choose Save/Reboot to apply the changes and reboot the system. Now we only show you how to add PVC. 3.5.1.1 Configure PPPoE Click “Add” to add a certain piece of PVC. The following descrip ti ons are given by an example of adding “PVC 8/35” (PPPOE mode).
PPP Username: the correct user name that your ISP has provided to you. PPP Password: the correct password that your ISP has provided to you. PPPoE Service Name: If your ISP provided it to you, please input it. Unless don’t input anything. Authentication Method: AUTO, PAP, CHAP, MSCHAP.
Multicast, WAN Service. IGMP Multicast: IGMP proxy. For example, if you need PPPoE mode support IPTV, please enable it. WAN Service: Please enable it, unless you don’t need to active the PVC. Click “Next” to show the following interface. In this interface, it shows the all configura tion .
modifications. NOTE: You need to reboot to activate this WAN interface and further configure services over this interface. 3.5.1.2 Configure PPPoA Click “Add” to add a certain piece of PVC. The following descrip ti ons are given by an example of adding “PVC 8/35” (PPPOA mode).
Click “Next”. In this interface, you can modify the PPP Username, PPP Password, Authentication Method and so on. PPP Username: the correct user name that your ISP has provided to you. PPP Password: the correct password that your ISP has provided to you.
In this interface, you can modify the Serv ice name and enable/disable the IGMP Multicast, WAN Service. IGMP Multicast: IGMP proxy. For example, if you need PPPoA m od e support IPTV, please enable it. WAN Service: Please enable it, unless you don’t need to active the PVC.
Click “Next”. In this interface, you can modi fy the WA N IP address, Default Gateway and DNS Server settings. Obtain an IP address automatically: The ROUTER will obtain a (WAN) IP address autom atically and at this time it will enable DHCP Client function s.
After correctly modif ications, click “Next” to show the f ollowing interface. In this interface, you can modify the Service name and enable/disable the NAT, Firewall, IGMP Multicast, WAN Service. Enable NAT: Select it to enable the NAT func tions of the ROUTER.
Click “Next”. In this interface, you can m odify the WAN IP, Default Gateway and DNS Server settings. WAN IP Address: Input the IP address of the WAN interface provided by your ISP. WAN Subnet Mask: Input the subnet mask concerne d to the IP address of the WAN interface provided by your ISP.
IGMP Multicast, WAN Service. Enable NAT: Select it to enable the NAT func tions of the ROUTER. If you are not to enable NAT and intend the user of the ROUTER to access the Internet normally, you must add a route on the up link eq uipment; otherwise the access to the Internet will fail.
Click “Next”. In this interface, you can modify the Service name. WAN Service: Please enable it, unless you don’t need to active the PVC. Click “Next”. In this interface, it shows the all configuration. Click “Save” to save thes e settings.
Enable IGMP Snooping: It used to Bridge mode. 3.5.3 NA T Click “NAT” to show the following interface. Under “NAT”, there are four network share modes: “virtual Server”, “p ort triggering”, and “DMZ Host”.
When NAT is enabled on the ROUTER, the w hole LAN that the ROUTER is attached will appear as a single machine on the In ternet. Normally, externa l users are not allowed to visit the PCs in the whole LAN to whic h the ROUTER is att ached. But under some circumstances, we hope that some PCs will b e open and allow anyone to acces s them.
Service Name: Select one service item, such as Mail (SMTP), Mail (POP3), Web Server (HTTP), FTP Server, and TFTP, from the list. The information about the selected item will appear in the box below. Customized server: Enter a new service name to establis h a specified user service category.
A maximum 32 entries can be configured. 3.5.3.3 NAT -- DMZ Host Click “DMZ Host” to pop up an interface as below. In this interface, you can conf igure DMZ services. Demilitarized Zone (DMZ) is a techn ology that enables the ROUTER to forward all in put packets onto a serv er specified in ternally.
3.5.4 Security Click “Security” -->” IP Filtering” to show the following interfac e. By default, the firewall is enabled. The firewall is used to blo ck document transmissions between the Internet and your PC. It serves as a safety guard and only permits authorized documents to be sent into the LAN.
3.5.4.2 Incoming IP Filtering Setup Click “Security”-->” IP Filte ring” -->” Inco ming” to show the following interface. By default, all incoming IP traffic f rom the WAN is blocked when the firewall is enabled. However, some IP traffic can be ACCEPTED by setting up filter s.
3.5.4.3 Parental Control Click “Security”-->”Paren tal Contro l” to show the following interface. Click “add” to show the interface. This page adds time of day restriction to a special LAN device connected to the Ro uter.
Click “ENABLE Automatic Assigned Default Ga teway” box to show the interface. 3.5.5.2 Routing – Static Route In this interface, you can modify the Static Route settings.
3.5.6 DNS 3.5.6.1 DNS Server In this interface, you can modify the DNS server settings. If 'Enable Automatic Assigned DNS' checkbox is se lected, this router will accept the first received DNS assignment from one of the PPPoA, PPPoE or MER/DHCP enabled PVC(s) during the connection establishment.
Click “Add” to add dynamic DDNS. 3.5.7 DSL In this interface, you can modify the DSL settings. Select one you need. But the default setting check G.dm t / G.lite / T1.413 / ADSL2 / ADSL2+ / Bitswap / SRA. The ROUTER will negotiate the modulation m ode with the DSLAM.
3.6 Diagnostics Click “Diagnostics” to show the interface. Your router is capable of testing your DSL connection. Th e individual tests are listed below. If a test displays a fa il status, click "Rerun Diagnostic Tests" at the bottom of this page to make sure the fail status is consiste nt.
3.7.1.2 Settings Update Click the “Browsing...” button, select the co rrect update configure settings file. Then click the “Update Settings” to update the Router settings.
Click “Restore Default Settings” to restore DSL router settings to th e factory defaults. 3.7.2 System Log Click “System Log” to show the following interface. The system log dialog allows y ou to view the system log and configure the system log options.
If you select “Remote” or “Both”, all even ts will be transm itted to the specified UDP port of the specified log server. After operations under “Configure System Log”, click “View System Log” to query the system logs. In this example, the “View Syste m Log” is a system default one.
you can enable/disable the HTTP, ICMP, SNMP, TELNET and TFTP services. And the LAN side and WAN side can have different configurations. 3.7.4.2 Access Control -- IP Addresses Click “Access Control”-->”IP Addresses” to show the following interf ace.
management station perm itted to access th e local management services, and click “Save/Apply”. 3.7.4.3 Access Control – Passwords Click “Access Control”-->”Passw ords” to show the following interface. In the interface, you can modify the accounts passwords.
before the reboot is over. You must guarantee the update so ftware is right and accurate. It is strictly forbidden to us e other software for updates. After update software, it is suggested to re store the ROUTER to the factory defaults and configure it again.
. Descriptions In this example, the ROUTER is connected to the DSLAM through PVC 8/35 and the access mode is the built-in PPPOA+NAT. The encapsulation of the BRAS downlink port is PPP OVER ATM, the authentication is AUTO, the IP address is 10.28.106.200, the IP Pool is 10.
You can also modify the PVC 8/35. If you ne ed to modify the LAN IP address and DHCP server information, you can do it in “LAN” in “Advanced Setup”. After the dial-up is successful, the IP addre ss that the ROUTER obtains at the WAN-side port ppp_8_35_1.
3. In the “ ATM PVC Configuration” interface configu re VPI/VCI as 8/35 and then click “Next”. 4. In the “ Connection Type ” interface, select “PPP over Ethernet (PPPoE)” and “LLC/SNAP-BRIDGING” as the encapsula tion, and then click “Next”.
address of the ROUTER is automatically obtai ned through DHCP; the PC attached to the ROUTER is assigned with a private IP a ddress (within the same segment as the management IP address 192.168.1.1); the NAT func tions of the ROUTER is enabled, and the private address of the PC is transl ated into the public address 10.
If “Enable NAT” is disabled during the conf iguration, you must configure the route on the BRAS; otherwise you cannot access your ISP. In applications, “Enable NAT” must be checked. 4.4 IP over A TM (IPoA) +NA T Mode Descriptions In this example, the ROUTER is connected to the DSLAM through PVC 8/35 and the access mode is the IPOA+NAT.
“LLC/SNAP-ROUTING” as the encapsu lation, and then click “Next”. 5. In the “ WAN Setting s” interface, input the IP addr ess, subnet mask, and DNS server address provided by your ISP. Don’t select “Use the following default gateway”.
10.28.108.1. Setting 1. Activate your browser and input “192.168.1.1” in the address column to login the ROUTER. 2. Click “ Advanced Setup ” -> “ WAN ”, then click “add”. 3. In the “ ATM PVC Configuration” interface configu re VPI/VCI as 8/35 and then click “Next”.
by BRAS through its built-in PPPOE dial-up. The ROUTER will assi gn this public IP address to the PC (configured as “Obtain an IP address autom atically”) attached to it in the DHCP mode. At this time, NAT will have no eff ect. From the point view of the user, the ROUTER seems working in the “Briding” mode.
62 2. Question: Why LINK/ACT LED is not lighting? Answer: • Check the connection between the ADSL r outer and your comput er or Hub/Switch. • Check your PC or Hub/Switch running st atus and make sure them are working normally.
An important point after buying a device Planet Technology ADE-3410v2 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Planet Technology ADE-3410v2 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Planet Technology ADE-3410v2 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Planet Technology ADE-3410v2 you will learn all the available features of the product, as well as information on its operation. The information that you get Planet Technology ADE-3410v2 will certainly help you make a decision on the purchase.
If you already are a holder of Planet Technology ADE-3410v2, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Planet Technology ADE-3410v2.
However, one of the most important roles played by the user manual is to help in solving problems with Planet Technology ADE-3410v2. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Planet Technology ADE-3410v2 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
