Instruction/ maintenance manual of the product SGC Pitco Frialator
Go to page of 30
Installation and Operation Manual For Gas Fryers NO OPTIONS/STAND ALONE Covering Models SG & SG F 14, 14R, 14T, 18, 18F, 24P, 24F, 34P, 34F & SGC Pitco Frialator, Inc., P.O. Box 501, Jct I-89 & I-93 Concord, NH 03302-0501 • 509 Route 3A, Bow, NH 03304 (800) 258-3708 • (603) 225-6684 • FAX (603) 225-8497 www.
L20-195 rev 4 (07/02) THIS MANUAL MUST BE RET AINED FOR FUTURE REFERENCE FOR YOUR SAFETY DO NOT stor e or use gasoline or other flammable vapors or liquids in the vicinity of this or any other appliance. W ARNING Improper installation, alteration, service or maintenance can cause property damage, injury or death.
1 L20-195 rev 4 (07/02) CHECKING YOUR NEW FRYER Your new fryer has been carefully packed into one crate. Every effort has been made to ensure that your fryer is delivered to you in perfect condition. As you unpack your new fryer, inspect each of the pieces for damage.
2 L20-195 rev 4 (07/02) Fuel Types - Each fryer is equipped to work with one type of fuel. The type of fuel with which the appliance is intended to operate is stamped on the data plate attached to the inside of the door. NOTICE NEVER use an adaptor to make a smaller gas supply line fit the cooker connection.
3 L20-195 rev 4 (07/02) LIGHTING INSTRUCTIONS a. Fill kettle before lighting. b. Turn combination gas valve knob to “PILOT” position. c. Depress valve knob and light pilot. W ith pilot burning, hold knob depressed for 60 seconds. d. Release knob, pilot should remain lit.
4 L20-195 rev 4 (07/02) W ARNING Gas units installed with casters must have a restraining device. This device must be connected at all times that the fryer is connected to the gas supply . If it is disconnected for any r eason, it must be reconnected.
5 L20-195 rev 4 (07/02) Fryer Shut-Down There are two shutdown modes of fryer operation, STANDBY and COMPLETE. The standby mode removes the ability for the fryer's main burners to cycle. Complete shutdown turns off the gas supply to the fryer. Shut down the fryer by: STANDBY Turn the thermostat to OFF.
6 L20-195 rev 4 (07/02) IF MAINTENANCE IS REQUIRED, CONT ACT YOUR LOCAL F ACTOR Y SER VICER, LOCAL F ACTOR Y REPRESENT A- TIVE, OR THE F ACTOR Y TO OBT AIN SER VICE.
7 L20-195 rev 4 (07/02) ENGLISH.
8 L20-195 rev 4 (07/02) In the event of problems with or questions about you equipment, please contact the Pitco Frialator Autho- rized Service and Parts representative (ASAP) cov- ering you area, thr.
Il y a Toujours Quelque Chose qui Mijote chez Nous ! Manuel d’Installation et de Fonctionnement Pour Friteuses à Gaz Modèles SG et S G F 14, 14R, 14T, 18, 18F, 24P, 24F, 34P, 34F et SGC Pitco Frialator, Inc.
A VER TISSEMENT T oute mauvaise installation, altération, réparation et tout mauvais réglage ou entretien risque de provoquer des dégâts matériels, des blessures graves, voire la mort.
11 L20-195 rev 4 (07/02) V ÉRIFICATION DE LA NOUVELLE FRITEUSE Votre nouvelle friteuse a été emballée avec précaution dans une caisse. Tout a été prévu afin que la friteuse vous soit livrée en parfaite condition.
12 L20-195 rev 4 (07/02) T ypes de carburants: Chaque friteuse est équipée afin de fonctionner avec un seul type de carburant. Le type de carburant destiné à cet appareil est indiqué sur la plaque signalétique fixée à l’intérieur de la porte.
13 L20-195 rev 4 (07/02) INSTRUCTIONS D’ALLUMAGE a. Remplissez la machine avant de l’allumer . b. T ournez la commande de gaz jusqu’à “PILOT” (veilleuse). c. Appuyez sur le bouton de la commande et allumez la veilleuse. Pendant que la veilleuse brûle, maintenez le bouton appuyé pendant environ 60 secondes.
14 L20-195 rev 4 (07/02) c. Vidangez l’huile de la friteuse et jetez-la ou conservez-la afin de la réutiliser plus tard. Retirez les tamis des tubes de filtrage ainsi que tout débris de grosse taille demeurant au fond de la cuve. Après avoir nettoyé les tamis des tubes de filtrage, remettez-les en place.
15 L20-195 rev 4 (07/02) pour retirer en grattant le mastic d’étanchéité de la vis de réglage. FRANCAIS d. T ournez la vis de réglage dans le sens de aiguilles d’une montre afin d’abaisser la température et dans le sens inverse pour l’élever .
16 L20-195 rev 4 (07/02) ARTICLE DOCUMENT UNDERWRITERS DOCUMENT DU CODE LABORA TORIES NA TIONAL POUR GAZ COMBUSTIBLE HOTTE D’EXTRACTION ANSI/UL 710 ANSI/NFP A 96 VENTILA TEURS ANSI/UL 705 ANSI/NFP A.
17 L20-195 rev 4 (07/02) FRANCAIS.
18 L20-195 rev 4 (07/02) Veuillez contacter votre représentant agréé Pitco Frialator si vous avez des problèmes ou des questions concernant votre équipement par l’intermédiaire du réseau de s.
¡Siempre Algo Cocinándose! Manual de Instalación y Operación de Freidores de Gas Cubre los Modelos SG & S G F 14, 14R, 14T, 18, 18F, 24P, 24F, 34P, 34F & SGC Pitco Frialator, Inc., P.O. Box 501, Jct I-89 & I-93 Concord, NH 03302-0501 • 509 Route 3A, Bow, NH 03304 (800) 258-3708 • (603) 225-6684 • FAX (603) 225-8497 www.
AL COMPRADOR Coloque en una ubicación prominente las instrucciones que deban seguirse en caso de que un operador perciba el olor de gas. Obtenga este tipo de información solicitándolo a su distribuidor local de gas. ADVERTENCIA Hay llama abierta en el interior de este fr eidor .
21 L20-195 rev 4 (07/02) REVISION DE UN FREIDOR NUEVO Su nuevo freidor ha sido cuidadosamente embalado en empaque de transporte. Se ha hecho todo esfuerzo para asegurar que el freidor le llega en condiciones perfectas. A medida que usted lo desempaca, inspeccione cada una de sus partes para detectar si han sufrido algún daño.
22 L20-195 rev 4 (07/02) Tipos de Combustible - Cada freidor está equipado para trabajar con un cierto tipo de combustible. El tipo de combustible para el cual el aparato se ha diseñado está indicado en la placa de especificaciones que se encuentra en lado interior de la puerta del freidor.
23 L20-195 rev 4 (07/02) INSTRUCCIONES DE ENCENDIDO a. Llene la marmita antes de encender el gas. b. Gire la perilla de la válvula de combinación de gas a la posición “PILOT”. c. Oprima la perilla de la válvula y encienda el piloto. Con el piloto encendido mantenga la perilla oprimida por 60 segundos.
24 L20-195 rev 4 (07/02) c. Drene el aceite del freidor y disponga de él, o consérvelo para ser usado nuevamente. Remueva la reja tubular y las mallas tubulares y saque los depósitos sólidos que encuentre en el fondo del tanque de freír. Una vez éste limpio, vuelva a colocar la reja tubular y las mallas en el tanque de freír.
25 L20-195 rev 4 (07/02) CALIBRACION DEL TERMOSTATO Termostato Millivolt a. Fije el dial del termostato en 325°F (163°C). b. Remueva el dial del termostato jalando de la perilla, derecho hacia afuera. NO haga girar el dial. c. Sostenga el exterior del eje de manera que no se mueva.
26 L20-195 rev 4 (07/02) TEMA UNDER WRITERS’S LABORA T OR Y NACIONAL FUEL GAS DOCUMENTO CODIGO DOCUMENTO CAMP ANAS DE EXTRACCCION ANSI/UL 710 ANSI/NFP A 96 VENTILADORES DE POTENCIA ANSI/UL 705 ANSI/.
27 L20-195 rev 4 (07/02) ESP ANOL.
L20-195 rev 4 (07/02) 2 8 En caso de problemas o preguntas relativas a su equipo, por favor comuníquese con el representante de Partes y Servicio Autorizado (ASAP) encargado de su zona, a través de la Red Nacional de Servicio llamando al: (800) 298-1862 en los Estados Unidos únicamente, servicio de 24 horas.
An important point after buying a device Pitco Frialator SGC (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Pitco Frialator SGC yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Pitco Frialator SGC - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Pitco Frialator SGC you will learn all the available features of the product, as well as information on its operation. The information that you get Pitco Frialator SGC will certainly help you make a decision on the purchase.
If you already are a holder of Pitco Frialator SGC, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Pitco Frialator SGC.
However, one of the most important roles played by the user manual is to help in solving problems with Pitco Frialator SGC. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Pitco Frialator SGC along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
