Instruction/ maintenance manual of the product BDP-LX08 Pioneer
Go to page of 72
Operating Instructions Blu-ray Disc PLAYER LX08_WV_EN.b ook 1 ページ ２００８年 ７月１５日 火曜日 午後２時５１分.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (ser vicing) instructions in the literature accompanying the appliance.
This pr oduct com p lies with the Low V oltage Di r ective 2006/95/EC and EMC Di r ective 2004/108/EC. D3-4-2-1-9a_A_En .
Information for users on collection and disposal of old equipment and used batteries These symbols on the products, packaging, and/or accompanying documents mean that used electrical and electronic products and batteries should not be mixed with general household waste.
01 5 En Contents 01 Before you start What’s in the box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Putting the batteries in the remo te control. . . . . . . . . . . . . . . . . . . 6 Types of discs/files that can be pla yed.
01 6 En Chapter 1 Before you start What’s in the box Putting the batteries in the remote control 1 Open the rear cover. 2 Insert the batteries (AA/ R6 x 2). Insert as indicated by the / marks into the battery compartment. 3 Close the rear cover.
7 En 01 Types of discs/files that can be played Playable discs Discs with the logo marks below indicated on the disc label, package or jacket can be played.
01 8 En Note • Some discs cannot be played, even if one of the above logo marks is indica ted. • To play 8 cm discs, set the disc in the 8 cm disc depression in the center of th e disc tray. No adapter is nece ssary. 8 cm BD- ROMs cannot be played.
9 En 01 About region numbers Blu-ray Disc Player and BD-ROM or DVD-Video discs are assigned region numbers according to the region in which they are sold. This player’s region numbers are: •B D - R O M : B •D V D - V i d e o : 2 Discs not in cluding these n umb ers cannot be played.
01 10 En • MPEG-1 Audio Layer 3 (MP3) Bit rate: Up to 320 kbps Sampling frequencies: 8 kHz, 11.025 kHz, 12 kHz, 16 kHz, 22.05 kHz, 24 kHz, 32 kHz, 44.1 kHz and 48 kHz Playable file extensions • Movie files .divx and .avi • Music files .wma and .
11 En 01 16 FL DIMMER Press to switch the brightness of the front panel displa y. The FL OFF indicator lights when Off is select ed. 17 ANGLE Press to switch the BD-ROM or DVD-Video camera angles (page 28). 18 OUTPUT RESOLUTION Use these to switch the output video resolution from the HDMI OUT or COMPONENT VIDEO output terminals ( page 24).
01 12 En Front Panel 1 STANDBY/ON Press to turn the power on and off. 2 Remote control sensor Point the remote control to this, then operate it within approximately 7 m. The player may have trouble ca pturing remote control signals if there is a fluorescent light nearby.
13 En 01 Rear Panel 1 AUDIO OUT (2 ch) t erminals Connect wi th the audi o input term inals on a TV, A V receiver or amplifier, etc. 2 AUDIO OUT (7 .1 ch) ter minals Connect with the multi-channel (7.1- o r 5.1-channel) audio input terminals on an AV receiver or ampl ifier, etc.
02 14 En Chapter 2 Connecting up Connecting a TV Be sure to turn off the power and un plug the power cord from the power outlet whenever making or changing connections. Note • Make the se ttings in th e Setup Naviga tor menu acc ording to the type of cable connected (page 20).
15 En 02 Audio signals that can be transferred with the player’s HDMI output terminal •D o l b y T r u e H D •D o l b y D i g i t a l P l u s •D o l b y D i g i t a l • DTS-HD Master Aud.
02 16 En Connecting using a commercially available component video cable Caution • When connected to the TV using a compo nent video cable (commercially available), video signals are not output with a resolution of 1080/50i, 1080/50p, 720/50p, 1080/24p o r 1080/60p.
17 En 02 Connecting an AV receiver or amplifier Connect to an AV receiver or amplifier in order to enjoy the surround sound of Dolby TrueHD, Dolby Digi ta l Plus, Dolby Di gital, DTS-HD Master Audio, DTS-HD High Re solution Audio or DTS Digital Surround.
02 18 En Connecting using audio cables Caution • For DTS-HD Master A udio and DTS-HD High Resolution Audio signals, the DTS Digital Surround signals are converted to linear PCM for output (page 50).
19 En 02 Connecting the power cord Connect the power cord after a ll the connections between devices have been completed. R R AUDIO OUT ( 2 ch ) AUDIO OUT ( 7.
03 20 En Chapter 3 Getting Started Making settings using the Setup Navigator menu Be sure to perform th ese settings when using the player for the first time. Caution • Before turning on the power, check that the conn ections between the player and o ther devices are correct.
21 En 03 5 Select and set the HDM I High-S peed Transmission setting. Use / to select, then press ENTER . •W h e n HDMI High-Speed Transmission is set to On , us e a High Speed HDMI™ cable. The picture an d sound may not be output properly if any other HDMI cable (standard HDMI™ cable) is used.
03 22 En About the screen saver The screen saver is automatically activated if there is no o peration for over 1 minute after pla yback is stopped or paused. The screen saver turns off when an operation is perfor med on the player or remote cont rol.
23 En 03 Using the TOOLS menu Various functions can be called out according to the player’s operating status. 1 Display the TOOLS menu. Press TOOLS . 2 Select and set the item. Use / to select, then press ENTER . Note • Items that cannot be changed are displayed in gray.
03 24 En Erasing the additional data from BD-ROMs When a BD-ROM is played, addition a l data may be stored in the player’s memory (local storage). If the message indicating low memory (local storage) appe ars, erase the BDMV data.
25 En 03 The output video resolution dep ends on the video output term inal. See the table below. The table below shows the output vide o resolution for the different terminals when the frame/field frequency of the playback source is 50 Hz on the upper line, the resolutions when the sou rce's frame/ field frequency is 60 Hz on the lower line.
04 26 En Chapter 4 Playback Playing discs or files This section describes the player’s main operations. For the types of discs that can be played, see Playable discs on page 7. For the types of files that can be played, see Playable files on page 9.
27 En 04 Playing specific ti tles, chapters or tracks Input the number of the title, chap ter or track you want to play. • Use the number buttons (0 to 9) to input the numbe r, then press ENTER . Note • For some discs, it is n ot poss ible to specify and play titles, chapters or tracks.
04 28 En Switching the camera angles For BD-ROM and DVD-Video disc s on which mu ltiple angles ar e recorded, the angles can be switched during playback. During playb ack, press ANGLE. • The current angle and to tal number of recorded angles ar e displayed on the TV screen and o n the player’s front panel display.
29 En 04 • Secondary au dio mark is di splayed for scenes at which secondary audio is recorded. Note • In some cases the secondary au dio may switch or the switching screen provided on the disc ma.
04 30 En 3 Input the time. Use the number buttons (0 to 9) or / to input the time. Use / to move the cursor. Note • To play from 45 minutes, in put 0 , 0 , 4 , 5 , 0 and 0 , then press ENTER . • To play from 1 hour 20 minutes, input 0 , 1 , 2 , 0 , 0 and 0 , then press ENTER .
31 En 04 Playing a specific section within a title or track repeatedly (A-B Repeat) Use this procedure to play a specif ic sectio n within a ti tle or track repeate dly. 1 During playback, press PLAY MODE to display the Play Mode screen. The Play Mode screen can also be displayed by sele cting Play Mode from the TOOLS menu.
04 32 En Playing in random order (Random Play) Use this procedure to play the tr acks or files in random order. 1 During playback, press PLAY MODE to display the Play Mode screen. The Play Mode screen can also be displayed by sele cting Play Mode from the TOOLS menu.
33 En 04 About Play Mode t ypes The functions that can be used di ffer according to the type of disc and file. In some cases, some of the functions canno t be us ed. Check the usable functions on the table below. Play Mode type Mark 1 1. During playback in a Play Mode, the type of Play Mode is in dicated by the mark.
04 34 En Playing from the Home Media Gallery The Home Media Gallery lets you displa y a list of the titles, tracks or files recorded on the disc. The di scs that can be pla yed from the Home Media Gallery are a s shown below (see also page 7 ).
35 En 04 3 Select Movies. Use / to select Movies , then press ENTER . 4 Select Folders or All Movies. Use / to select, then press ENTER . • Folders – The files in the selected folder are displayed. • All Movies – All the recorded files are displayed.
04 36 En • All Songs – All the recorded files are displayed. If you have selected All Songs , proceed to step 6. 5 Select the folder containing the file you wa nt to play. Use / to select, then press ENTER . A list of t he files and /or the sub - folders in the selected folder is displayed.
37 En 04 4 Press TOOLS to display the TOOLS menu. 5 Select Add to HMG Playlist. Use / to select, then press ENTER . The track or file selected in st ep 3 is added to the HMG Playlist.
05 38 En Chapter 5 Adjusting audio and video Adjusting the video The quality of the playback picture can be adju sted according to the TV you are using. 1 During playback, press VIDEO ADJUST to displa y the Video Adjust screen. The Video Adjust screen can al so be displayed by selecting Video Adjust fr om the TOOLS menu.
39 En 05 Closing the Video Adjust screen Press HOME MENU . About Pure Cinema There are two types of video signals: • Video materia l – Video signals recorded at 25 or 30 frames/ second •.
06 40 En Chapter 6 Advanced settings Changing the settings (Initial Setup) Operating the Initial Setup screen 1 When playback is stopped, displ ay the Home Menu scre en. Press HOME MENU . 2 Select and set In itial Setu p. Use / to select, then press ENTER .
41 En 06 Note • Items that cannot be changed are indicated in gray. The it ems that can be selected depend on the player’s status. • The factory default settings are indicated in bold . Setting Options Explanation Video Out TV Aspect Ratio 16:9 (Widescr een) Select this when connected to a wide (16:9) TV.
06 42 En HDMI HDMI High-Speed Transmission On Select this when conn ected with a High Spee d HDMI™ cable (page 1 5). Off Select this when connected with a Standard HDMI™ cable (page 15). The player’s setting screen is close d if the output video resolution is switc hed by changing the HDMI High-Speed Transmissi on setting.
43 En 06 Changing to other language at language setting Note •R e f e r t o Language Code Table on page 56. • If a language not recorded on the BD/DVD is set, one of the recorded languages is automa tica lly selected and played. 1 Select and set Other.
06 44 En Changing the speaker setup Set whether or not to use the spea kers which a re connected to th e AV receiver or a mplifier, as we ll as the size of the speakers. This setting is only valid for analog audi o outputs. Note • Select Initial Se tup from the HOM E MENU, then press ENTER .
45 En 06 3 Select and set the method for switch ing the speaker to be adjusted. Use / to select, then press ENTER . • Auto – Switch the speaker to be ad justed automatically. • Manual – Switch the sp eaker to be adjus ted manually. Caution • Test tones are output.
06 46 En Use / to move the cursor. To change the code number Input the previously registered password, then input the new password. Note • We recommend making a note of the password. • If you forget the password, reset th e player to the factory default setting, then register the password again (page 49).
47 En 06 Changing the Parent al Lock level for watching DVDs Some DVD-Video discs containing sc enes of violence, for example, have Parental Lock levels (check the indications on the disc’s jacket or elsewhere). To restrict watching these discs, set the player’s level to the level lower than th e discs.
06 48 En Changing the Country/Area code Note •R e f e r t o Country/Area Code Tabl e on page 56. 1 Select and set Parental Lock. Use / to select, then press ENTER . 2 Select and set Country/Area Code. Use / to select, then press ENTER .
49 En 06 Changing the terminals for outputting video and audio signals (Output Terminal Priority) Set the video and audio termi nals to be used. 1 Select and set Options. Use / to select, then press ENTER . 2 Select and set Output Terminal Prio rity Next Screen.
06 50 En About the audio output settings The audio signals that are outp ut differ according to the audio format recorded on the disc and the pla yer’s settings.
51 En 07 Chapter 7 Additional information Troubleshooting Incorrect operation i s often mistake n for trouble or malfunctio n. If you think that there is something wr ong with this componen t, check the points below. Sometimes the trouble may lie in another component.
07 52 En Picture is stretc hed. Aspect ratio cannot be switched. Is the TV’s aspect ratio properly set? Read the TV’s operating instructions an d set the TV’s aspect ratio properly. Is 4:3 Video Out properly set? • Set 4:3 Video Out prope rly (pag e 41).
53 En 07 Digital audio signals are n ot output from the DIGITAL OUT (OPTICAL) terminals (analog audi o signals ar e output). Is Audio O ut set to audio format s supported by the conne cted AV receiver or amplifier? • Read the o perating instructio ns of the connected AV receiver or amplifier and check the supported audio formats.
07 54 En When connected usin g an HDMI cable Problem Check Remedy HDMI indicator does not light. Is the input of the connected H DMI device properly set? Read the HDMI device’s operat ing instructions and set the input properly.
55 En 07 Others Problem Check Remedy The power turns off automatic ally. Is Auto Power Off set to On ?I f Auto Power Off is set to On , the power turns off automaticall y if no opera tion is perfor med for over 3 0 minutes (page 43). Is HDMI Control set to On ? The player’s power ma y turn of f together with the power of the connected TV .
07 56 En Language Code Table and Country/Area Code Table Language Code Table Language name (langua ge code), input code Country/Area Code Table Country/Area name, input code, Country/Area code Japanes.
57 En 07 Specifications Note • The specificat ions and design of this pr oduc t are subject to ch ange without notice . • This product includes FontAvenue ® fonts licensed by NEC Corporation . FontAvenue is a r egistered trade mark of NEC Co rporation.
07 58 En Cautions on use Moving the player If you need to move this unit, first rem ove the disc if there’s one loaded, and close the disc tray. Next, press STANDBY/ON to switch the power to standby, checking that the POWER OFF indication on the front panel displa y goes off.
59 En 07 Handling discs Do not use damaged (cracked or warped) discs. Do not scratch the disc’s signal surface or let it get d irty. Do not load more than one disc into the player at a time. Do not glue paper or put stickers onto the disc, or use a pencil, ball- point pen or o ther sharp- tipped writin g instrument.
07 60 En Deep Color This is one of the ca pabilities of HDMI™. Th e players supporting Deep Color can transmit a video si gnal with a color bit depth of greater than 8 bits per color component. Su btle color gradations can be reproduced when connecte d to a TV that s upports Deep Color.
61 En 07 Region number A number assigned to Blu-ray Di sc Players, BD-ROM and DVD- Video discs according to the region in which they are sold. A disc can be played if the region numb ers indicated on the disc include the number set for the player or if “ALL” is indicated.
07 62 En Licenses The licenses for the software used on this player a re shown below. libxml2 The MIT License Copyright © <year> <copyright holders> Permission is hereby granted, free.
63 En 07 Introduction The FreeType Project i s distributed in several archive packages; so me of them may contain, in addition to the FreeType font eng ine, various tools and contributions which rely on, or relate to, the FreeType Project.
07 64 En libpng versions 0.89, June 199 6, through 0.96, May 1997, are Cop yright © 1996, 1997 An dreas Dilger Distributed according to the same disclaimer and license as libp ng- 0.
65 En 07 In order to support file conversion and viewing software, we have included considerable function ality beyo nd the bare JPEG codi ng/decoding capability; for example, the color quantization modules are not strictly part of JPEG decoding , but they are essential for output to colormapp ed file format s or colormapped displays.
07 66 En The TIFF 6.0 file format specif ication can be obtained by FTP from ftp://ftp.sgi.com/graphics/ti ff/TIFF6.ps.gz. The JPE G incorp oration scheme found in the TIFF 6.0 spe c of 3-June-92 ha s a number of serious probl ems. IJG does n ot recommend use of the TIFF 6.
67 En 07 The precis e terms a nd cond itions for copying, distribu tion and modificat ion follow. TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND MODIFICATION 0. This License applies to any program or other work which contains a notice placed by the copyri ght holder saying it may be dis tributed under the t erms of this General Public License.
07 68 En 11. B ECAUSE THE PROGRAM IS LI CENSED FREE OF CHARG E, THERE IS NO WARRANT Y FOR THE PROGRAM, TO THE E XTENT PERMITTED BY AP PLICABLE LAW. EXCEPT WHEN OTHERWISE ST ATED IN WRITING T HE COPYRI.
69 En 07 In other case s, permission to use a partic ular library in non-free programs enables a greater number of people to use a large b ody of free software.
07 70 En d) If distribution of the work is made by o ffering access to copy from a designated place, offer equivalent access to copy the a bove specified materials from the same place. e) Verify that the user has already received a copy of these materials or that you have al ready sent this user a c opy.
71 En 07 [Notice on GNU General Public License] This product include the software licensed for use und er the terms of a GNU General Public License. A copy of the corresponding source code can be obtained by being charged the fee for distribution. To obtain a copy, contact your loca l Pioneer Customer Support Center.
Printed in <VRB1506-A> Discover the benefits of registering your product online at http://www.pioneer.co.uk (or http://www.pioneer.eu) Published by Pioneer Corporation. Copyright © 2008 Pioneer Corporation. All rights reserved. PIONEER CORPORATION 4-1, Meguro 1-Chome, Meguro-ku, Tokyo 153-8654, Japan PIONEER ELECTRONICS (USA) INC.
An important point after buying a device Pioneer BDP-LX08 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Pioneer BDP-LX08 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Pioneer BDP-LX08 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Pioneer BDP-LX08 you will learn all the available features of the product, as well as information on its operation. The information that you get Pioneer BDP-LX08 will certainly help you make a decision on the purchase.
If you already are a holder of Pioneer BDP-LX08, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Pioneer BDP-LX08.
However, one of the most important roles played by the user manual is to help in solving problems with Pioneer BDP-LX08. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Pioneer BDP-LX08 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
