Instruction/ maintenance manual of the product 6050 Athena Technologies
Go to page of 15
Instruction Manual Athena 6050 Temperature Controllers -THENIL.
INSTRUCTION MANUAL SPECIFICATIONS: Inputs: Line Voltage Sensor Power Consumption Ranges Available Accuracy: Temperature Stability Cold end tracking Operating ambient for rated accuracy Maximum T/C lea.
Display update rate: 5 times per second Filtering: Analog and digital filtering techniques increase stability of process and display. °F/°C: output: -B Relay (time proportioning) -F Current proporti.
3.
FRONT PANEL AOJUSTMENTS Touch Key 1 Index: Allows the following adjustments to be selected. 1) Set point temperature O-14OO'F (760°C) O-2500°F (O-137O°C) 2) Heat cycle time 3) Prop.
3. 4. Loss of power or turn-off during warm-up requires a re-start from ambient. Change of state processes, i.e. solid to liquid or liquid to gas, may introduce erroneous tuning parameters during process warm-up. 1. Accurately measures, linearizes and displays temperature in °F and °C.
.
Output Modules The Athena 6050 offers users field interchangeable output modules. This unique feature makes it possible to fill output requirements for a variety of applications with a single controller model. Module Type B: This 7A/5A relay (at 120/240 Vac) is used for driving resistive heaters.
INTERNAL SWITCHES Damping Control -To allow the controller to provide automatic tuning for processes with varying heating characteristics and with varying heating capabilities, the 6050 offers three d.
THERMOCOUPLE PLACEMENT Proper thermocouple placement can eliminate many problems in the system. The probe should be placed so that it can detect any temperature change with minimal thermal lag. In a process that requires fairly constant heat output, the probe should be placed close to the heater.
OPERATING INSTRUCTIONS How to Start the automatic tuning procedure STEP 1: Energize the unit and proceed immediately to step 2. STEP 2: Place the unit on standby by holding the "Index" button until the "Autotune" LED lights then press the Cancel button.
How to override automatic tuning parameters It is possible to set or fine tune three mode parameters manually on the 6050. To manually enter parameters: 1) Press "Index" button until the LED for the desired parameter lights. 2) Enter the new parameter using the up or down key.
TROUBLE SHOOTING Front dark - no instrument power. Process display shows CCCC - Open thermcouple. Short terminals 1 and 2. Process display should indicate temperature at back of case. Repair or replace thermocouple. About Half or Twice Expected Reading - Check position of °C/°F switch.
WARRANTY This equipment is warranted to be free from defects of material and workmanship. It is sold subject to our mutual agreement that the liability of Athena Controls, Inc. is to replace and/or repair at its factory, provided the equipment is returned, transportation prepaid within (2) years of its purchase.
dTHENd Controls, Inc., 5145 Campus Drive Plymouth Meeting, PA 19462 (215) 828-2490.
An important point after buying a device Athena Technologies 6050 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Athena Technologies 6050 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Athena Technologies 6050 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Athena Technologies 6050 you will learn all the available features of the product, as well as information on its operation. The information that you get Athena Technologies 6050 will certainly help you make a decision on the purchase.
If you already are a holder of Athena Technologies 6050, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Athena Technologies 6050.
However, one of the most important roles played by the user manual is to help in solving problems with Athena Technologies 6050. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Athena Technologies 6050 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
