Instruction/ maintenance manual of the product H50IMW-AD Perlick
Go to page of 31
MODELS: H50IMS-R H50IMS-L H50IMW H50IMS-ADL H50IMS-ADR H50IMW-AD PERLICK SELF-CONTAINED ICE MAKER P R O D U C T M A N U A L Issued: 11-2-2009.
2 IMPORTANT This manual should be read carefully before the icemaker is installed and operated. Only qualied service technicians should install, service, and maintain the icemaker. Read the warnings contained in this booklet carefully as they give important information regarding safety.
3 Important Safety Information Throughout this manual, notices appear to bring your attention to situations which could result in death, serious injury, or damage to the unit. WARNING Indicates a hazardous situation which could result in death or serious injury.
4 I. Specications A. Construction Top Panel Ice Making Mechanism Scoop Holder Front Panel Control Switch Louver Bin Control Thermostat Bulb Slope Magnet Catch Door Power Cord.
5 PERLICK ICE MAKER MODEL NUMBER H50IMS-R SERIAL NUMBER AC SUPPLY VOLTAGE 115-120/60/1 AMPERES 3.4 AMPS DESIGN PRESSURE HI-240PSI LO-120PSI REFRIGERANT 134a 4.2 oz. B. Nameplate Rating See the nameplate for electrical and refrigeration specications.
6 Units: mm [in.] C. Dimensions/Connections 1. H50IMS-R, H-50IMS-L.
7 2. H50IMW Units: mm [in.].
8 3. H50IMS-ADL, H50IMS-ADR Units: mm [in.].
9 4. H50IMW-AD Units: mm [in.].
10 II. Installation and Operating Instructions WARNING 1. This icemaker must be installed in accordance with applicable national, state, and local regulations. 2. CHOKING HAZARD: Ensure all components, fasteners, and thumbscrews are securely in place after installation.
11 2. Built-In Installation Site CAUTION 1. Do not let the weight of the counter rest on the icemaker. 2. Do not install the icemaker in a corner where the door will interfere with other equipment or where the icemaker cannot be pulled out for service.
12 1 2 3 4 6 5 C. D oo r Ov er la y P an el F ab ri ca ti o n an d At ta ch me nt (H 50 IM W, H 50 IM W- AD) IMPORTANT The overlay panel must be crafted by a professional cabinet maker to ensure quality results. (1) Parts Ensure that all parts required for the overlay panel assembly are contained in the accessories bag.
13 (2) Overlay Panel Specification Use the specication that applies to your icemaker (H50IMW or H50IMW-AD) and the directions that follow to prepare your overlay panel.
14 H50IMW-AD Overlay Panel Specication Overlay Panel Height 27 9/16" (700 mm) Overlay Panel Width 14 13/16" (376 mm) Overlay Panel Thickness 5/8" (16 mm) minimum; 3/4" (19 mm) maximum Overlay Panel and Door Weight (total) 20 lb.
15 3) Screw the 6 threaded wood inserts into the 1/4" holes drilled in the previous step. Make sure that the inserts are threaded straight and that the tops of the inserts are ush to the overlay panel surface. Otherwise, the overlay panel cannot be properly fastened to the door.
16 Screws f) Remove hinge (C1) from the top right part of the door, ip it and reattach to the bottom left. Remove hinge (C2) from the bottom right part of the door, ip it and reattach to the top left. See Fig. 8. Proceed to step 7. d) Remove hinge (B) from the right side of the unit and the 2 ller screws from the left side.
17 9) Temporarily fasten the overlay panel to the door using 2 of the M4×25 pan head screws provided. See Fig. 11. CAUTION Ensure that the back surface of overlay panel is at before attaching. 10) Mark the centerpoint of the hinge (C1) and hinge (C2) holes that extend over the overlay panel.
18 Snug the screws, but do not tighten. Sheet Metal Bracket Overlay Panel Tighten the screws. 5) Fasten the overlay panel to the door using the four M4×25 pan head screws provided. Snug the screws, but do not tighten. See Fig. 17. 6) Fasten the sheet metal bracket to the bottom of the door with the three T2 screws provided.
19 7) Tighten the four M4×25 pan head screws installed in step 5. See Fig. 19. 8) Replace the door gasket in its proper orientation. Reinsert the bushings into hinge (C1) and hinge (C2) (the hinges attached to the door). See Fig. 20. Canoe Clips Fig.
20 D. Setup 1) Position the icemaker in the selected permanent location. 2) Level the icemaker from side-to-side and front-to-rear by adjusting the feet. E. Electrical Connection WARNING 1. Electrical connection must meet national, state, and local electrical code requirements.
21 F. Water Supply and Drain Connections WARNING 1. Water supply and drain connections must be installed in accordance with applicable national, state, and local regulations. 2. Normal operating water temperature should be within 45°F to 95°F (7°C to 35°C).
22 G. Final Checklist WARNING CHOKING HAZARD: Ensure all components, fasteners, and thumbscrews are securely in place after installation. Make sure that none have fallen into the storage bin.
23 H. Startup WARNING 1. All parts are factory-adjusted. Improper adjustments may adversely affect safety, performance, component life, and warranty coverage. 2. If the icemaker is turned off, wait for at least 3 minutes before restarting the icemaker to prevent damage to the compressor.
24 III. Cleaning and Maintenance WARNING 1. CHOKING HAZARD: Ensure all components, fasteners, and thumbscrews are securely in place after any cleaning or maintenance is done to the unit. Make sure that none have fallen into the storage bin. 2. The storage bin is for ice use only.
25 3) Inside the storage bin, disconnect the suction tube by squeezing the tabs and pulling the tube clear. See Fig. 26. Allow the water tank to drain. 4) Reconnect the suction tube as illustrated. See Fig. 27. Make sure the tabs lock into place; a loose tting may cause a water leak.
26 3. Sanitizing Solution IMPORTANT For safety and maximum effectiveness, use the solution immediately after dilution. Dilute 0.5 . oz. (14.8 ml or 1 tbs) of a 5.25% sodium hypochlorite solution (chlorine bleach) with 1 gallon (3.8 l) of warm water.
27 Reducing Pipe Rail Rail 13) Position and lock the ice chute onto the front and rear frame pipes by pushing the ice chute down until it clicks onto both frame pipes. See Fig. 36. 14) Slide in the water tank along the rails at the bottom of the left and right brackets until it locks into place.
28 15) Reconnect the suction tube. 16) Hook each separator onto the rail, then pull it hard towards you until it locks into place. See Fig. 38. 17) Replace the slope in its correct position. See Fig. 39. Fig. 38 18) Discard the sanitizing solution. 19) Mix a new batch of the sanitizing solution and slowly pour it into the water tank.
29 B. Maintenance IMPORTANT This icemaker must be maintained individually, referring to the instruction manual and labels provided with the icemaker. 1. Stainless Steel Exterior To prevent corrosion, wipe the exterior occasionally with a clean and soft cloth.
30 C. Preparing the Icemaker for Long Storage CAUTION When storing the icemaker for an extended time or in sub-freezing temperatures, follow the instructions below to prevent damage. When the icemaker is not used for two or three days under normal conditions, it is sufcient to move the control switch to the "OFF" position.
31 .
An important point after buying a device Perlick H50IMW-AD (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Perlick H50IMW-AD yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Perlick H50IMW-AD - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Perlick H50IMW-AD you will learn all the available features of the product, as well as information on its operation. The information that you get Perlick H50IMW-AD will certainly help you make a decision on the purchase.
If you already are a holder of Perlick H50IMW-AD, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Perlick H50IMW-AD.
However, one of the most important roles played by the user manual is to help in solving problems with Perlick H50IMW-AD. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Perlick H50IMW-AD along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center