Instruction/ maintenance manual of the product Pump Pentair
Go to page of 10
Rev. D 6-5-01 1 P/N 071109 WARNING Risk of electrical shock or electrocution. This pool pump must be installed by a licensed or certified electrician or a qualified pool serviceman in accordance with the National Electrical Code and all applicable local codes and ordinances.
P/N 071109 2 Rev. D 6-5-01 Note When pump is mounted permanently within 5 ft. of the inside walls of a swimming pool, you must use a No. 8 AWG or larger conductor to connect to bonding conductor lug. WARNING To reduce the risk of injury, do not permit children to use this product unless they are closely supervised at all times.
Rev. D 6-5-01 3 P/N 071109 6. Permanently ground the motor using the green ground terminal located on the inside of the motor canopy or access plate, see Figure 1. Use the correct wire size and type specified by National Electrical Code. Make sure the ground wire is connected to an electrical service ground.
P/N 071109 4 Rev. D 6-5-01 WARNING THIS FILTER OPERATES UNDER HIGH PRESSURE. WHEN ANY PART OF THE CIRCULATING SYSTEM (e.g., LOCK RING, PUMP, FILTER, VALVES, ETC.) IS SERVICED, AIR CAN ENTER THE SYSTEM AND BECOME PRESSURIZED. PRESSURIZED AIR CAN CAUSE THE LID TO BLOW OFF WHICH CAN RESULT IN SEVERE INJURY, DEATH, OR PROPERTY DAMAGE.
Rev. D 6-5-01 5 P/N 071109 SECTION III. SERVICE. A. Pump Disassembly. 1. All moving parts are located in the rear sub-assembly of this pump. Tools required: a. 3/32 inch Allen head wrench. b. ½ inch open end wrench. c. 9/16 inch open end wrench. d. Flat blade screwdriver.
P/N 071109 6 Rev. D 6-5-01 B . Pump Reassembly/Seal Replacement; see Section V, Technical Data, Figure 4. 1. When installing the replacement shaft seal, use silicone sealant on the metal portion, before pressing into the seal plate. 2. Before installing the ceramic section of the seal into the impeller, be sure the impeller is clean.
Rev. D 6-5-01 7 P/N 071109 B. Priming the Pump. 1. The pump strainer pot must be filled with water before the pump is initially started. Follow these steps to prime the pump. a. Remove the pump lid plastic clamp. Remove the pump lid. b. Fill the pump strainer pot with water.
P/N 071109 8 Rev. D 6-5-01 A. Replacement Parts. Item Part Model Description No. No. No. Item Part Model Description No. No. No. SECTION VI. TECHNICAL DATA.
Rev. D 6-5-01 9 P/N 071109 B. Pump Curves. SAVE THESE INSTRUCTIONS. Single Speed Models Dual Speed Models.
P/N 071109 10 Rev. D 6-5-01 Pentair Pool Products WhisperFlo ™ Circulating Pump Limited W arranty Pentair Pool Products manufactures its WhisperFlo circulating pumps under high standards of workmanship and with high quality materials.
An important point after buying a device Pentair Pump (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Pentair Pump yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Pentair Pump - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Pentair Pump you will learn all the available features of the product, as well as information on its operation. The information that you get Pentair Pump will certainly help you make a decision on the purchase.
If you already are a holder of Pentair Pump, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Pentair Pump.
However, one of the most important roles played by the user manual is to help in solving problems with Pentair Pump. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Pentair Pump along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center