Instruction/ maintenance manual of the product 81CP0101 Pella
Go to page of 9
P art Number: 81CP0101 ©2012 P ella Corpor ation INST ALLA TION INSTRUCTIONS - INS TRUCCIONE S P ARA LA INS T ALACIÓN CLAD WINDOWS WITH FL USH FLANGE Lea las instrucciones en español en el r everso Installation Instructions for Replacement of Aluminum Windows in Har d Coat Stucco Applications in arid climates.
2" 1A Y OU WILL NEED TO SUPPL Y : • CompositeorImperviousshims/spacers (12 to 20) • P ressure-tr eated2x4(4-6ft) • 3-1/4”nishheadscrews(16-20) • W oodblockingtosupportnewwindow.
1/4" minimum Sealant 1F Repeat steps C - E for all four sides of the opening. F. Remove any debris, paint or stucco from the exterior face of the existing window frame that will interfere with the new window installation. Clean any dirt or debris from the e xisting sill and ensure the weep holes are open and clear .
I. Install wood blocking around the entir e opening. The blocking must be the same height as the existing aluminum window frame. The blocking must extend to the interior far enough to provide full support for the sill of the new window, however may extend as far to the interior as desired.
Drill 1/8" clearance hole Double-Hung Jamb 1/4" Double-Hung Head Drill 1/8" clearance hole 1/2" Double-Hung Sill Drill 1/8" clearance hole 1/2" Clad Frame Sill Drill 1/8&.
Window Frame 3/4" Min. A. T est fit the window in the opening from the exterior . Inser t shims around the window temporarily while you verify that thewindowwilltintotheopeningand the window flanges will overlap the stucco or existing aluminum window frame by a minimumof3/4"onall(4)sides.
A. Place a corner bead of sealant on the edge of the window flush flange on top, sides and bottomtothestucco. Leavea2"gapinthe sealant bead at the bot tom, corresponding to the weep hole locations in the existing aluminum window frame.
Theexteriorfr ameandsashareprotectedbyaluminumcladdingwithourtoughEnduraClad ® or EnduraCladPlusbaked-onfactorynishtha trequiresnopainting. Cleanthissurfacewithmild soap and water .
INST ALLING ROTO COVER AND CRANK Note: Y ou may want to remove the lock lever prior to finishing the window, or if it needs to be replaced with a lock lever in a differ ent finish. A. Unlock and open the window . B. Place the lock lever in the locked position.
An important point after buying a device Pella 81CP0101 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Pella 81CP0101 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Pella 81CP0101 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Pella 81CP0101 you will learn all the available features of the product, as well as information on its operation. The information that you get Pella 81CP0101 will certainly help you make a decision on the purchase.
If you already are a holder of Pella 81CP0101, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Pella 81CP0101.
However, one of the most important roles played by the user manual is to help in solving problems with Pella 81CP0101. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Pella 81CP0101 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center