Instruction/ maintenance manual of the product 812WO100 Pella
Go to page of 10
INST ALLA TION INSTRUCTION - INSTRUCCIONES DE INST ALACIÓN FOR CLAD AWNING, CASEMENT & NON-RECT ANGULAR CASEMENT WINDOW p ARA LAS VENT ANAS DE MADERA RECUbIERT AS DE ALUMINIO TIpO bISAGRAS, bA TIENTE y bA TIENTE NO-RECT ANGULAR Installation Instructions for T ypical W ood F rame Construction.
YOU WILL NEED T O SUPPL Y : T OOLS REQUIRED: • Cedar or Impervious shims/spacers (12 to 20) • 2" galvanized roofing nails (1/4 lb .) • Closed cell foam backer rod/sealant backer (12 to 30 ft.
E. Apply sill flashing tape #1 . C ut a piece of flashing tape 12" longer than the opening width. Apply at the bottom of the opening as shown (1E) so it o verhangs 1" to the exterior . N ote: The tape is cut 12" longer than the width so that it will extend 6" up each side of the opening.
Interior 2F 2F F . Plumb and square windo w . Place shims 1" from the bottom and top of the window between the window and the sides of the opening. Adjust the shims as required to plumb and squar e the window in the opening. If the frame height exceeds 53", place shims at the midpoint of the window sides.
1 2 0 3 0 4 0 5 0 6 0 7 0 2 3 INCHES mm 2G 2I N ote: The flashing tape must be applied approximately 1/2" onto the frame cladding at the jambs and head. P re-folding the tape at 1/2" before r emoving the paper backing will make it easier to apply the tape correctly .
3D 3C 3D Exterior 3C 3C 3B 3 INTEGRA TING THE WINDOW TO THE W A TER RESISTIVE bARRIER (continued) C. F old down top flap of water r esistive barrier (3C). D. Apply flashing tape to diagonal cuts . C ut pieces of flashing tape at least 1" longer than the diagonal cuts in the water resistive barrier .
Caution: Ensur e use of low pr essur e polyurethane windo w and door insulating foams and strictly follow the foam manufactur er ’ s r ecommendations for application. Use of high pr essur e foams or improper application of the foam may cause the window frame to bow and hinder oper ation.
A. Insert backer rod into the space around the windo w approximately 3/8" deep . This should pro vide at least a 3/8" clearance between the backer rod and the exterior face of the window . N ote: Backer rod adds shape and depth for the sealant line.
INTERIOR FINISHING If products cannot be finished immediately , co ver with clear plastic to protect from dirt, damage and moisture. Remo ve any construction residue before finishing. S and all wood surfaces lightly with 180 grit or finer sandpaper .
INST ALLING ROTO COVER AND CRANK N ote: Finish the interior of the windo w and allow the window to dry before proceeding with these instructions. (T o open the window for finishing, partially insert the lock handle into the jamb, unlock the unit, temporarily attach the crank handle and turn to open.
An important point after buying a device Pella 812WO100 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Pella 812WO100 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Pella 812WO100 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Pella 812WO100 you will learn all the available features of the product, as well as information on its operation. The information that you get Pella 812WO100 will certainly help you make a decision on the purchase.
If you already are a holder of Pella 812WO100, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Pella 812WO100.
However, one of the most important roles played by the user manual is to help in solving problems with Pella 812WO100. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Pella 812WO100 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
