Instruction/ maintenance manual of the product 812W0100 Pella
Go to page of 11
INST ALLA TION INSTRUCTION - INSTRUCCIONES DE INST ALACIÓN FOR CLAD AWNING, CASEMENT & NON-RECT ANGULAR CASEMENT WINDOW P ARA LAS VENT ANAS DE MADERA RECUBIERT AS DE ALUMINIO TIPO BISAGRAS, BA TIENTE Y BA TIENTE NO-RECT ANGULAR Installation Instructions for T ypical W ood F rame Construction.
YOU WILL NEED T O SUPPL Y : T OOLS REQUIRED: • Cedar or Impervious shims/spacers (12 to 20) • 2" galvanized roong nails (1/4 lb .) • Closed cell foam backer rod/sealant backer (12 to 30 ft.
E. Apply sill ashing tape #1 . C ut a piece of ashing tape 12" longer than the opening width. Apply at the bottom of the opening as shown (1E) so it o verhangs 1" to the exterior . N ote: e tape is cut 12" longer than the width so that it will extend 6" up each side of the opening.
Interior 2F 2F F. Plumb and square windo w . Place shims 1" from the bottom and top of the window between the window and the sides of the opening. Adjust the shims as required to plumb and squar e the window in the opening. If the frame height exceeds 53", place shims at the midpoint of the window sides.
1 2 0 3 0 4 0 5 0 6 0 7 0 2 3 INCHES mm 2G 2I G. Check the interior reveal . M ake sure the measurement fr om the interior face of the window to the interior face of the wall is equal at several points around the window . N ote: If the dimensions are not equal, check to make sur e the ns ar e folded out to 90° at all points.
3D 3C 3D C. F old down top ap of water r esistive barrier (3C). D. Apply ashing tape to diagonal cuts . C ut pieces of ashing tape at least 1" longer than the diagonal cuts in the water resistive barrier . Apply the tape co vering the entire diagonal cut in the water resistive barrier at both upper corners of the window .
Exterior 3C 3C 3B 3 INTEGRA TING THE WINDOW TO THE WA TER RESISTIVE BARRIER (continued) Curv e T op and Angle T op U nits Only: A. U nits that do not hav e pr e-applied n corners: Cut four pieces of ashing tape 1-1/2" long.
Caution: Ensur e use of low pr essur e polyurethane windo w and door insulating foams and strictly follow the foam manufactur er ’ s r ecommendations for application. Use of high pr essur e foams or improper application of the foam may cause the window frame to bow and hinder oper ation.
A. Insert backer rod into the space around the windo w approximately 3/8" deep . is should provide at least a 3/8" clearance between the backer rod and the exterior face of the window . N ote: Backer rod adds shape and depth for the sealant line.
INTERIOR FINISHING If products cannot be nished immediately , co ver with clear plastic to protect from dirt, damage and moisture. Remo ve any construction residue before nishing. S and all wood surfaces lightly with 180 grit or ner sandpaper .
INST ALLING ROTO COVER AND CRANK N ote: Finish the interior of the windo w and allow the window to dry before proceeding with these instructions. (T o open the window for nishing, partially insert the lock handle into the jamb, unlock the unit, temporarily attach the crank handle and turn to open.
An important point after buying a device Pella 812W0100 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Pella 812W0100 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Pella 812W0100 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Pella 812W0100 you will learn all the available features of the product, as well as information on its operation. The information that you get Pella 812W0100 will certainly help you make a decision on the purchase.
If you already are a holder of Pella 812W0100, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Pella 812W0100.
However, one of the most important roles played by the user manual is to help in solving problems with Pella 812W0100. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Pella 812W0100 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
