Instruction/ maintenance manual of the product 80GY0102 Pella
Go to page of 10
Part Number: 80GY0102 ©2008 Pella Corporation Always read the P ella ® Limited W arranty before purchasing or installing P ella products. B y installing this product, you ar e acknowledging that this Limited W arranty is part of the terms of the sale.
A. V erify the opening is plumb and level. N ote: It is critical that the bottom is level. 1 ROUGH OPENING PREP ARA TION REMEMBER T O USE APPR OPRIA TE PERSONAL PR O TECTIVE EQUIPMENT . B. V erify the windo w will fit the opening. M easure all four sides of the opening to make sure it is 1/2" larger than the windo w in both width and height.
D. F old the water r esistiv e barrier (1D). F old side and bottom flaps into the opening and staple to inside wall. F old top flap up and temporarily fasten with flashing tape. % &YUFSJPS ' & ( E.
B. Windows using F rame Screws: On the roomside of vent windows, drill 13/64" diameter clearance holes thr ough the head, jambs and sill of the frame. S pace the holes using the maximum end and on center spacings as shown on the placement diagram.
3 SETTING AND F ASTENING THE WINDOW TWO OR MORE PEOPLE WILL BE REQUIRED FOR THE FOLL O WING STEPS. " *OUFSJPS # # & A. Insert the windo w from the exterior of the building. Place the bottom of the window on the spacers at the bottom of the opening, then tilt the top into position.
A. Apply side flashing tape . C ut two pieces of flashing tape 5" longer than the frame height of the window . Apply the tape 1/2" onto the frame cladding, ov er the fin and laps onto the water resistive barrier . The tape should extend 2" abov e the top of the window and 3" below the bottom of the window .
B. Drill 1/8" x 1" deep pilot holes into the rough framing through the clearance holes in the unit frame. C. F asten the windo w to the opening by driving #10 x 3-1/2" corrosion resistant wood scr ews into each of the pre-drilled clearance holes.
8 SEALING THE WINDOW TO THE EXTERIOR W ALL CLADDING When applying siding, brick veneer or other exterior finish material, leave adequate space between the window fr ame and the material for sealant. Refer to the illustration that corresponds to y our finish material.
INTERIOR FINISHING If products cannot be finished immediately , cover with clear plastic to pr otect from dirt, damage and moisture. R emove any construction residue befor e finishing. Sand all wood surfaces lightly with 180 grit or finer sandpaper .
INST ALLING ROTO COVER AND CRANK LOCK LEVER REMOV AL AND INSER TION N ote: Finish the interior of the windo w and allow the windo w to dr y before proceeding with these instructions. (T o open the window for finishing, partially insert the lock handle into the jamb, unlock the unit, temporarily attach the cr ank handle and turn to open.
An important point after buying a device Pella 80GY0102 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Pella 80GY0102 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Pella 80GY0102 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Pella 80GY0102 you will learn all the available features of the product, as well as information on its operation. The information that you get Pella 80GY0102 will certainly help you make a decision on the purchase.
If you already are a holder of Pella 80GY0102, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Pella 80GY0102.
However, one of the most important roles played by the user manual is to help in solving problems with Pella 80GY0102. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Pella 80GY0102 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
