Instruction/ maintenance manual of the product 803V0102 Pella
Go to page of 12
P art Number: 803V0102 © 2012 P ella Corpor ation INST ALLA TION INSTRUCTIONS IMPERVIA ® SLIDING P A TIO DOOR WITH FINS Installation Instructions for T ypical W ood Fr ame Construction. These instructions wer e developed and tested for use with typical wood frame wall construction in a wall system designed to manage water .
YOU WILL NEED T O SUPPL Y : Ř Cedar or Impervious shims/spacers (12 to 20) Ř 2" galvanized roofing nails (1/4 lb.) Ř Closed cell foam backer r od/sealant backer (24 to 32 ft.
Exterior 1D ' & ( ) D. Fold the wa ter resistive barrier . Fold side flaps into the opening and staple to the inside wall. F old the top flap up and temporarily fasten with flashing tape.
A. Place three 3/8" beads of sealant. The first bead should be approxima tely 3/4" from the exterior of the rough opening, the second 2-1/2" in fr om the first bead of sealant. OX/X O doors only: Place a third bead of sealant in the groove of the sill support or 1/4" from the exterior edge of the wood blocking.
A. Apply side flashing tape. Cut two pieces of flashing tape 4" longer than the frame height of the door . Apply one piece to each side over the nailing fin and onto the water resistive barrier . T he tape should extend 2" above the top of the door and 2" below the bottom of the door .
Caution: Ensure use of low expansion polyurethane window and door installa tion foams and strictly follow the foam manufacturer’ s recommendations for application. Use of high expansive foams or improper application of the foam may cause the door to bow and hinder operation.
" # Note: Application of closed cell foam backer r od and sealant does not apply to stucco. A. Insert closed cell foam backer r od into the space around the door as deep as it will go. T his should provide at le ast a 1/2” clearance between the backer r od and the exterior face of the door .
MULLING INSTRUCTION HORIZONT AL MULLIONS: Note: If transoms are to be attached (mulled) to the top of the unit, perform this process before a ttaching fins. A. Apply two strips of foam tape across the bottom of the transom frame. Note: The tape must extend the full width of the transom frame.
VERTICAL MULLIONS: A. Lay the units on a smooth clean surface, exterior side up to perform these steps. & 9 5 & * 0 3 3 * # * / 5 & * 0 3 3 * # # % & & 9 5 & * 0 3 3 * # * / 5 & * 0 3 3 * # ' B. Apply two strips of foam tape down the fixed door frame sides.
APPL YING INST ALLA TION FINS A. Cut the fins to length. Using the following formula, cut the fins to length, making sure the end cut is square on both ends.
APPL YING HEAD DRIP FIN - REQUIRED FOR VER TICAL MULLION APPLICA TIONS A. Apply a bead of sealant along the whole width of the mulled composite behind the exterior rib. B. On vertical mulls, cut the head drip to the width of the units. Attach the head drip to the top of units aligning the ends and seal to the frame on both ends.
T his page lef t blank intentionally ..
An important point after buying a device Pella 803V0102 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Pella 803V0102 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Pella 803V0102 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Pella 803V0102 you will learn all the available features of the product, as well as information on its operation. The information that you get Pella 803V0102 will certainly help you make a decision on the purchase.
If you already are a holder of Pella 803V0102, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Pella 803V0102.
However, one of the most important roles played by the user manual is to help in solving problems with Pella 803V0102. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Pella 803V0102 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
