Instruction/ maintenance manual of the product 802X0104 Pella
Go to page of 8
Installation Instructions for T ypical W ood F rame Construction. These instructions were developed and tested for use with typical wood frame wall construction in a wall system designed to manage water . These instructions are not to be used with any other construction method.
REMEMBER T O USE APPROPRIA TE PERSONAL PR OTECTIVE EQ UIPMENT . 1 ROUGH OPENING PREP ARA TION A. V erify the opening is plumb and lev el. N ote: It is critical that the bottom is level. Interior 1A Interior 1B B. V erify the window will fit the opening.
E. Apply sill flashing tape #1. # UTAPIECEOFmASHINGTAPELONGER than the opening width. Apply at the bottom of the opening as shown %SOITOVERHANGSTOTHEEXTERIOR N ote: The tape is cut 12" longer than the width so that it will extend 6" up each side of the opening.
D. V erify the sill is flat ONTHEEXTERIOREDGENOTBOWEDORHUMPEDPRIORTO completing attachment of window to opening. N ote: If the sill is not flat screen fit issues may r esult.
5 INTERIOR SEAL Caution: Ensur e use of low pressur e polyurethane window and door insulating foams and strictly follow the foam manufactur er ’s r ecommendations for application. Use of high pressur e foams or improper application of the foam may cause the window frame to bow and hinder operation.
6 SEALING THE WINDOW TO THE EXTERIOR WALL CLADDING When applying siding, brick veneer or other exterior finish material, leave adequate space between the window fr ame and the material for sealant. Refer to the illustration that corresponds to your finish material.
A. F rom the interior , unlock the window and raise the lower sash to the fully open position. B. R otate the screen clips to the open position. C. Grasp the scr een to allow it to pass through the lower sash opening. D. P osition the screen into the window .
INTERIOR FINISHING )FPRODUCTSCANNOTBElNISHEDIMMEDIATELY COVERWITHCLEARPLASTICTOPR OTECTFROMDIR T DAMAGEANDMOISTURE2EMO VEANYCONSTRUCTIONRESIDUEBEFORElNISHING3ANDALLWOODSURFACES LIGHTLYWITHGRITORlNERSANDPAPER $/.
An important point after buying a device Pella 802X0104 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Pella 802X0104 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Pella 802X0104 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Pella 802X0104 you will learn all the available features of the product, as well as information on its operation. The information that you get Pella 802X0104 will certainly help you make a decision on the purchase.
If you already are a holder of Pella 802X0104, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Pella 802X0104.
However, one of the most important roles played by the user manual is to help in solving problems with Pella 802X0104. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Pella 802X0104 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
