Instruction/ maintenance manual of the product 801W0103 Pella
Go to page of 8
INST ALLA TION INSTRUCTION - INSTRUC CIONES DE INST ALACIÓN FOR CLAD SLIDING P A TIO DOOR PUERT A C ORREDERA P ARA P A TIO Installation Instructions for T ypical W ood F rame Construction. ese instructions were developed and tested for use with typical wood frame wall construction in a wall system designed to manage water .
D. F old the water resistiv e barrier (1D). Fold side aps into the opening and staple to inside wall. F old top ap up and temporarily fasten with ashing tape. YOU WILL NEED T O SUPPL Y : T OOLS REQUIRED: • Cedar or Impervious shims/spacers (12 to 20) • 2" galvanized roong nails (1/4 lb .
2 PREP ARE THE DOOR FOR INST ALLA TION A. Remo v e the plastic wrap and cardboar d packaging from the door . N ote: If screens, grilles or har dwar e are r emoved fr om the door at this time, label them and store them in a protected ar ea. 1 ROUGH OPENING PREP ARA TION (C ONTINUED) 2D 1H 1" 1G 1F 1" 1/2" 1/2" 6" 1E E.
3 SETTING AND F AS TENING THE DOOR A. Place three 3/8" beads of sealant. e rst bead should be approximately 3/4" from the exterior of the rough opening, the second 2-1/2" in from the rst bead of sealant. Place a third bead of sealant in the groov e of the sill support or 1/4" from the exterior edge of the wood blocking.
4 INTEGRA TING THE DOOR TO THE WA TER RESIS TIVE BARRIER A. Apply side ashing tape. C ut two pieces of ashing tape 4" longer than the frame height of the door . Apply one piece 1/2" onto the frame cladding, over the nailing n and onto the water resistive barrier on each side.
6 INTERIOR SEAL Caution: Ensur e use of low pr essur e polyurethane windo w and door insulating foams and strictly follow the foam manufactur er ’ s r ecommendations for application. Use of high pressur e foams or improper application of the foam may cause the door frame to bo w and hinder operation.
7 SEALING THE DOOR T O THE EXTERIOR WALL CLADDING When applying siding, brick veneer or other exterior nish material, leave adequate space between the door frame and the material for sealant. Refer to the illustr ation that corresponds to your nish material.
EXTERIOR FINISH e exterior frame and sash are protected by aluminum cladding with our tough E nduraClad® or EnduraClad Plus baked-on factory nish that needs no painting. Clean this surface with mild soap and water . Stubborn stains and deposits may be remo ved with mineral spirits.
An important point after buying a device Pella 801W0103 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Pella 801W0103 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Pella 801W0103 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Pella 801W0103 you will learn all the available features of the product, as well as information on its operation. The information that you get Pella 801W0103 will certainly help you make a decision on the purchase.
If you already are a holder of Pella 801W0103, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Pella 801W0103.
However, one of the most important roles played by the user manual is to help in solving problems with Pella 801W0103. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Pella 801W0103 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
