Instruction/ maintenance manual of the product Spectra IV SE Pelco
Go to page of 16
INSTALLATION Spectra ® IV Series Spectra ® IV SE Series C3417M-B (11/06) In-Ceiling Mount Back Box.
2 C3417M-B (11/06) Installation 1 3 4 2 5.
C3417M-B (11/06) 3 1. Locate the center point of th e mounting location and inser t the compass tool. Draw a circle. 2. Cut the circle out of the ceiling. 3. Attach the conduit fitting, lock nut, and safety chain bracket. Install a safety ch ain/cable (not supplied) that will support up to 16 poun ds (7.
4 C3417M-B (11/06) 6 7 VIDEO UTP+ UTP- RX- RX+ TX+ TX- PWR- PWR+ GND AUX2 GND GND NO NC COM 7 6 5 4 3 2 1 ALARMS AUX1.
C3417M-B (11/06) 5 6. Suspended Ceiling Only: Install the ceiling tile with th e back box. Attach a T -rail cl ip on each side of the ceiling tile. 7. Connect wiring to the circuit board inside the back box. Whe n finished, clos e the door to th e back box and tur n on the power .
6 C3417M-B (11/06) A 8 9 10 SWITCH 1 AND 2.
C3417M-B (11/06) 7 8. Configure DIP switche s SW1 and SW2 locate d on the top of the dome drive. For DIP switch settings, ref er to the labels locat ed on the top of the dome drive o r to the Switch Settings section. NOTE: When connecting mor e than one Spectra ® dome to a single cont roller , terminate th e unit farth est from th e controller .
8 C3417M-B (11/06) T roubleshooting If your dome do es not power u p properly after installati on, use the following steps. 1. Check the fuse on the circuit board inside the ba ck box for continuity . Replace the fuse if needed . 2. Check the wi ring with a vo lt meter to en sure pr oper voltage is being received into the back box.
C3417M-B (11/06) 9 Switch Settings WAR N IN G : If you are using D-ty pe or P-type control, your system may no t operate if the baud rate and address switches are not set corre ctly . T he switches are set at the fact ory at the de faults for D- type control (2400 baud an d address 1).
10 C3417M-B (11/06) T able F . Switch Settings for SW1, P-T ype Control NOTE: For Coaxitron controls, SW1 is not us ed; set all switches OFF . For D-type con trol systems, refer to T a ble G. T able G. Switch Settings for SW1, D-T ype Control NOTE: For Coaxitron controls, SW1 is not used; set all switches OFF .
C3417M-B (11/06) 11 SPECTRA ADDRESS SWITCH SETTI NG SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-8 71 ON ON ON OFF OFF OFF ON O FF 72 OFF OFF OFF ON OFF OFF ON OFF 73 ON OFF OFF ON OFF OFF ON O FF 74.
12 C3417M-B (11/06) SPECTRA ADDRESS SWITCH SETTI NG SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-8 151 ON ON ON OFF ON OFF OFF ON 152 OFF OFF OFF ON ON OFF OFF ON 153 ON OFF OFF ON ON OFF OFF ON 154 .
C3417M-B (11/06) 13 SPECTRA ADDRESS SWITCH SETTI NG SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-8 223 ON ON ON ON ON OFF ON ON 224 OFF OFF OFF OFF OFF ON ON ON 225 ON OFF OFF OFF OFF ON ON ON 226 OF.
14 C3417M-B (11/06) Specifications The materials used in the manufacture of this document and its co mponents are compliant to the requirements of Directive 2002/9 5/EC.
PRODUCT WARRANTY AND RETURN INFORMA TION WARRA NTY Pelco will r epair or repla ce, without charge, any merchandise p roved defectiv e in material or workmanship for a period of one year after the date of shipment.
W orldwide Headquarters 3500 Pelco W ay Clovis, California 93612 USA USA & Canada T el: 800/289-9100 Fax: 800/289-9150 International T el: 1-559/292-1981 Fax: 1-559/348-1120 www .
An important point after buying a device Pelco Spectra IV SE (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Pelco Spectra IV SE yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Pelco Spectra IV SE - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Pelco Spectra IV SE you will learn all the available features of the product, as well as information on its operation. The information that you get Pelco Spectra IV SE will certainly help you make a decision on the purchase.
If you already are a holder of Pelco Spectra IV SE, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Pelco Spectra IV SE.
However, one of the most important roles played by the user manual is to help in solving problems with Pelco Spectra IV SE. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Pelco Spectra IV SE along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
