Instruction/ maintenance manual of the product SD5AM Pelco
Go to page of 28
SD5BC Series Color or SD5AM Series Monochr ome Spectra II™ Dome Systems Operation and Programming Manual C2419M-A (5/00) ® P elco • 3500 P elco Wa y • Clovis, CA 93612-5699 USA • www .
2 Pelco Manual C2419M-A (5/00) CONTENTS Section Page IMPORT ANT SAFEGU ARDS AND W ARNINGS ................................................................ 3 OPERA TION ...................................................................................
Pelco Manual C2419M-A (5/00) 3 IMPOR T ANT SAFEGUARDS AND W ARNINGS Prior to installation and use of this product, the following W ARNINGS should be observed. 1. Installation and ser vicing should only be done by qualified service personnel and conform to all local codes.
4 Pelco Manual C2419M-A (5/00) OPERA TION POWER-UP DISPLA Y When the Spectra II™ dome is pow ered up , the selected protocol, re vision number , and other inf or mation is displa yed on the monitor .
Pelco Manual C2419M-A (5/00) 5 OPERA TING NOTES P AN AND TIL T FUNCTIONS Controller T ype Pan Tilt Fixed speed Speed determined by controller Speed determined by controller Va r iab le speed 0.
6 Pelco Manual C2419M-A (5/00) PA TTERNS The Spectra II dome can do either one full pattern (1.5, 3, or 6 minutes long) or two half patterns (.75, 1.5, or 3 minutes long). This patter n can consist of any standard pan and tilt or lens command. Presets, flip, and turbo are not allowed in a pattern.
Pelco Manual C2419M-A (5/00) 7 AUXILIAR Y OUTPUTS An A UX 1 command from the controller will activate the relay in the dome and oper ate the de vice that is connected to the relay .
8 Pelco Manual C2419M-A (5/00) PROGRAMMING Programming Guide - Spectra II LowLight Color Spectra II Monochrome 1. Access main menu (preset 95). 2. Make main menu selections . Joystic k: Move up or down to position cursor or to toggle between selections.
Pelco Manual C2419M-A (5/00) 9 ACCESSING MAIN MENU (PRESET 95) Y ou can call up the main menu on your monitor by progr amming (setting or creating) preset 95 (28 if in 32-preset mode). Programming preset 95 f or Pelco’ s controllers varies according to the type of controller you are using.
10 Pelco Manual C2419M-A (5/00) ALARMS The Spectra II dome has se ven alarm inputs, which can be designated as either high or lo w prior ity . The high priority setting is significant when more than one alarm is activated. If pr iority in alarms is not required, leave all alarms in the low setting.
Pelco Manual C2419M-A (5/00) 11 6. P osition the cursor (>) beside the number of the alarm input for which you w ant to set the pattern. 7. Press the Iris Open button. The cursor mov es to the r ight, beside the words Full P at, Half P at 1, Half P at 2, or No Pattern.
12 Pelco Manual C2419M-A (5/00) AUTO FLIP There are two auto flip modes: On - Auto flip mode is enab led. Off - A uto flip mode is disabled. To change the auto flip mode: 1. Program preset 95 (28). The main menu appears. 2. P osition the cursor (>) beside Other.
Pelco Manual C2419M-A (5/00) 13 AUTO IRIS The following are the settings for auto iris: Mode Level Peak To change the settings for auto iris: 1. Program preset 95 (28). The main menu appears. 2. Position the cursor (>) beside Camera. 3. Press the Iris Open button to enter the Camera menu.
14 Pelco Manual C2419M-A (5/00) AUX MODE A ux Men u Aux 1 mode Normal Aux 2 mode Normal Exit Main Menu <Camera> <Line Sync> <Power Up> <Aux> <Alarms, Zone Blank> <Other> EXIT There are three settings for A UX mode: Normal - Controller operated.
Pelco Manual C2419M-A (5/00) 15 Main Menu <Camera> <Line Sync> <Power Up> <Aux> <Alarms, Zone Blank> <Other> EXIT Camera Menu Backlight comp Off Zoom limit x- - Res.
16 Pelco Manual C2419M-A (5/00) LIMIT STOPS Main Menu <Camera> <Line Sync> <Power Up> <Aux> <Alarms, Zone Blank> <Other> EXIT Other Menu A uto flip On Proportional .
Pelco Manual C2419M-A (5/00) 17 LINE SYNCHRONIZA TION Main Menu <Camera> <Line Sync> <Power Up> <Aux> <Alarms, Zone Blank> <Other> EXIT Line Sync Menu Line sync On .
18 Pelco Manual C2419M-A (5/00) P ARK TIME MINUTES This feature causes the dome to park at preset 1 after a progr ammed number of minutes of control inactivity . The time can be set from 1 minute to 720 minutes (12 hours), or it can be set to zero, which disables this feature.
Pelco Manual C2419M-A (5/00) 19 This f eature lets the dome resume a desired condition follo wing power-up . The men u includes the following choices. Default - On power-up, the dome goes through a configuration cycle and stops at z ero ref erence, showing “Configur ation Done, ” address, and mode settings on the screen.
20 Pelco Manual C2419M-A (5/00) Main Menu <Camera> <Line Sync> <Power Up> <Aux> <Alarms, Zone Blank> <Other> EXIT Other Menu A uto flip On Proportional pan On Limit.
Pelco Manual C2419M-A (5/00) 21 RESET CAMERA Main Menu <Camera> <Line Sync> <Power Up> <Aux> <Alarms, Zone Blank> <Other> EXIT Camera Menu Backlight comp Off Zoom limit x- - Reset camera <Gain/AGC> <Auto-iris> <Next> Exit Resetting the camera returns the settings to their defaults .
22 Pelco Manual C2419M-A (5/00) SCAN SPEED Next Men u LowLight limit 2 Shutter speed Auto Auto focus mode Auto <Sharpness> <White balance> Prev (bac k to prev .
Pelco Manual C2419M-A (5/00) 23 SHUTTER SPEED Next Men u LowLight limit 2 Shutter speed Auto Auto focus mode Auto <Sharpness> <White balance> Prev (bac k to pre v .
24 Pelco Manual C2419M-A (5/00) WHITE BALANCE (Color Camera Only) Next Men u LowLight limit 2 Shutter speed Auto Auto focus mode Auto <Sharpness> <White balance> Prev (bac k to prev .
Pelco Manual C2419M-A (5/00) 25 NOTE: The Spectra II LowLight Color camer a cannot do electronic zoom in a pattern. Optical zoom will operate in a pattern.
26 Pelco Manual C2419M-A (5/00) MAINTENANCE DOME CLEANING Clean the acrylic dome as necessary to maintain a clear picture. Be careful not to scratch the surfaces of the dome. Exterior Surface - Clean the dome’ s exterior surface with a nonabr asive cleaning cloth and cleaning agent that is safe f or acr ylic.
Pelco Manual C2419M-A (5/00) 27 Horizontal Resolution: >470 TV lines Lens Minimum f-stop 16X: F1.4 22X: F1.6 Focal Length 16X: 4 mm to 64 mm optical 22X: 4 mm to 88 mm optical Zoom Ratio Spectra II.
28 Pelco Manual C2419M-A (5/00) P elco, the P elco logo, Camclosure, Esprit, Genex, Legacy , and Spectra are registered trademarks of P elco . © Cop yr ight 2000, P elc o. Endura and ExSite are trademarks of P elco. All rights reser ved. U .S. P atent No .
An important point after buying a device Pelco SD5AM (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Pelco SD5AM yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Pelco SD5AM - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Pelco SD5AM you will learn all the available features of the product, as well as information on its operation. The information that you get Pelco SD5AM will certainly help you make a decision on the purchase.
If you already are a holder of Pelco SD5AM, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Pelco SD5AM.
However, one of the most important roles played by the user manual is to help in solving problems with Pelco SD5AM. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Pelco SD5AM along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
