Instruction/ maintenance manual of the product MC5700 Pelco
Go to page of 12
MC5700 Series 1/3-Inch Monochr ome Camera Installation/ Operation Manual C1903M (4/99) Pelco • 3 5 00 Pelco Way • Clovis , CA 93612-5699 USA • www.
2 Pelco Manual C1903M (4/99) IMPOR T ANT SAFEGUARDS AND W ARNINGS 1. Installation and servicing should only be done by qualified service personnel and conform to all local codes. 2. T o pre v ent fire or shock hazard, do not e xpose the unit to rain or moisture .
Pelco Manual C1903M (4/99) 3 LOCA TION AND FUNCTION OF P ARTS Refer to Illustration B for the location of the camera parts listed below . NOTE: References to illus- trations in this manual are keyed to the illustrations in the manual that is supplied with the camera.
4 Pelco Manual C1903M (4/99) Be sure to attach the lens mount cap when the lens is not mounted. When using an auto-iris lens, use only a DC-driven type or a direct current drive coil with a resistance value over 150 ohms. When using an auto-iris lens, attach it as follows.
Pelco Manual C1903M (4/99) 5 E A C CS 2 1 4 3 CCD-IRIS ON OFF Lens Installation CCD-Iris Function.
6 Pelco Manual C1903M (4/99) NOT A V AILABLE ON 5700 SERIES Incident Light LENS CAMERA (STYLIZED) Iris opening (sometimes referred to as aperture) is defined by f/stop numbers.
Pelco Manual C1903M (4/99) 7 Information Box Information Box LENS TYPE MANUAL IRIS V ARIABLE LIGHT CONDITIONS ST A TIC LIGHT CONDITIONS AUT O IRIS • Turn Manual Iris ring so iris is fully open and set the Focus ring for ∞ (or distant object). • Adjust Backfocus with CCD IRIS switch initially set to the OFF position.
8 Pelco Manual C1903M (4/99) Information Box Information Box The purpose of backfocusing is to make the adjustments necessary for the picture to remain in focus throughout the camera’s zoom range, which is the case for instance, in motorized zoom, auto iris configurations.
Pelco Manual C1903M (4/99) 9 CAMERA Install the camera where it will not be affected by fluorescent lights or window reflections. If the camera is used under illumination that is not steady , the picture may flicker . The MC5700-2 must be operated with a 24 V AC, 60 Hz, Class 2 power supply.
10 Pelco Manual C1903M (4/99) V -PHASE ADJUSTMENT V ertical phase adjustment is required only if your system uses two or more cameras. The vertical phase can be manually adjusted within the range of approximately -90 degrees to +90 degrees (refer to Illustration H).
Pelco Manual C1903M (4/99) 11 INCIDENT LIGHT LEVEL ADJUSTMENT Since the incident light level has been preset at the factory , usually no further adjustment is required. If the picture is too dark, however , or if the picture’s highlights are extremely overexposed, adjust the LEVEL adjustment screw .
12 Pelco Manual C1903M (4/99) REVISION HISTOR Y Manual # Date Comments C1903M 1 1/96 Original version. 4/99 Added MC5700-2X model. Revised manual to new format. ® Pelco and the Pelco logo are registered trademarks of Pelco. © Copyright 1999, Pelco. All rights reserved.
An important point after buying a device Pelco MC5700 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Pelco MC5700 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Pelco MC5700 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Pelco MC5700 you will learn all the available features of the product, as well as information on its operation. The information that you get Pelco MC5700 will certainly help you make a decision on the purchase.
If you already are a holder of Pelco MC5700, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Pelco MC5700.
However, one of the most important roles played by the user manual is to help in solving problems with Pelco MC5700. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Pelco MC5700 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
