Instruction/ maintenance manual of the product MC3651H-2 Pelco
Go to page of 12
® Installation/Operation MC3651H-2 Series DSP Monochr ome Camera C1985M-E (4/03) Pelco World Headquarters • 3500 Pelco Way, Clovis, CA 93612-5699 USA • www.
[ 2 ] Pelco Manual C1985M-E (4/03) Prior to installation and use of this product, the following WARNINGS should be observed. 1. Installation and servicing should only be done by qualified service and installation personnel.
Pelco Manual C1985M-E (4/03) [ 3 ] CAMERA LA YOUT Figure 1. Camera Layout INST ALLA TION Lens Mounting The camera can use a fixed iris, manual iris, or auto iris. The camera is factory set for a CS-mount lens, but is easily adjusted for a C-mount lens.
[ 4 ] Pelco Manual C1985M-E (4/03) Power and Video Connections The MC3651H-2 camera is designed to operate from a 12 VDC or 24 V AC power supply . The power sup- ply connections are shown in Figure 1. The LED on the back panel of the camera indicates that power is connected.
Pelco Manual C1985M-E (4/03) [ 5 ] To connect the camera power and video: 1. Remove the cosmetic trim ring from the camera (refer to Figure 1). Thread cabling through the rear cover . 2. Connect the power cable to the two pin power connector on the back of the camera using the terminal block connector (provided).
[ 6 ] Pelco Manual C1985M-E (4/03) LENS SETUP AND FOCUS PROCEDURES V ideo Drive Auto Iris Lens When a video drive auto iris lens is used, the lens mode selector switch must be set to AIV . Switch the ESC and AGC OFF . Refer to the lens instructions and adjust the lens for the optimum picture (video out- put level of 1V peak-to-peak).
Pelco Manual C1985M-E (4/03) [ 7 ] Figure 5. Back Focus Adjustment BACK FOCUS ADJUSTMENT The back focus adjustment is located at the front of the camera and is accessible from either side of the case. To adjust the back focus: 1. Loosen the two back focus locking screws (one on each side).
[ 8 ] Pelco Manual C1985M-E (4/03) Figure 6. Default Settings OFF OFF OFF OFF AIV INT NOR OFF OFF OFF BLC AGC OPT ESC AID LL SHP LC DS1 DS2 ON PHASE LEVEL + - H L 1 2 3 4 5 6 7 8 9 10 00026 1 BLC - Back Light Compensation OFF (Default setting) - Disables the BLC mode.
Pelco Manual C1985M-E (4/03) [ 9 ] 7 NOR/SHP - Sharpness NOR (Default setting) - Sets the camera to normal sharpness mode. SHP - Enables the Sharpness mode. Enhances picture detail by increasing the aperture gain of the camera, sharpening the edges in the picture.
[ 10 ] Pelco Manual C1985M-E (4/03) CAMERA SYNCHRONIZA TION (AC OPERA TION ONL Y) When using more than one camera power supply , a brief vertical roll may occur on the monitor each time a camera view is switched. T o eliminate vertical roll, adjust the phase control by synchronizing, or line- locking, the cameras to one another .
Pelco Manual C1985M-E (4/03) [ 11 ] SPECIFICA TIONS GENERAL CCD Sensor: 1/3-inch interline transfer Picture Elements MC3651H-2: 768 (H) x 494 (V) MC3651H-2X: 795 (H) x 596 (V) Sensing Area: 6 mm diagonally Synchronize System: INT/AC line lock Horizontal Resolution 570 TV lines Iris Control: Electronic/passive Minimum Illumination 0.
[ 12 ] Pelco Manual C1985M-E (4/03) REVISION HISTOR Y Manual # Date Comments C1985M 10/00 Original version. C1985M-A 12/00 Added note for cosmetic trim ring. Revised switch setting illustration to depict default settings. C1985M-B 7/01 Added camera model MC3651H-2X.
An important point after buying a device Pelco MC3651H-2 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Pelco MC3651H-2 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Pelco MC3651H-2 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Pelco MC3651H-2 you will learn all the available features of the product, as well as information on its operation. The information that you get Pelco MC3651H-2 will certainly help you make a decision on the purchase.
If you already are a holder of Pelco MC3651H-2, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Pelco MC3651H-2.
However, one of the most important roles played by the user manual is to help in solving problems with Pelco MC3651H-2. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Pelco MC3651H-2 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
