Instruction/ maintenance manual of the product MC3600H-2 Pelco
Go to page of 16
Pelco • 3500 Pelco Way • Clovis, CA 93612-5699 USA • www.pelco.com In North America and Canada: Tel (800) 289-9100 or FAX (800) 289-9150 International Customers: Tel +1 (559) 292-1981 or FAX +1 .
[ 2 ] Pelco Manual C1982M-A (12/00).
Pelco Manual C1982M-A (12/00) [ 3 ] CONTENTS IMPORT ANT SAFEGUARDS AND W ARNINGS ................................................................................. 4 REGULA TOR Y NOTICES .................................................................
[ 4 ] Pelco Manual C1982M-A (12/00) IMPORT ANT SAFEGU ARDS AND WARNINGS Prior to installation and use of this product, the following WARNINGS should be observed. 1. Installation and servicing should only be done by qualified service and installation personnel.
Pelco Manual C1982M-A (12/00) [ 5 ] DESCRIPTION The MC3500 and MC3600 Series are compact, monochrome video cameras with a 1/3-inch CCD imager . All cameras have a direct drive/auto iris lens connector and adjustable back focus, and accept C and CS lenses.
[ 6 ] Pelco Manual C1982M-A (12/00) CAMERA LA Y OUT Figure 1. Camera Layout NOTE: The cosmetic trim ring conceals the LED light for more discreet surveillance operations.
Pelco Manual C1982M-A (12/00) [ 7 ] 3 4 12 PIN DD LENS CONNECTIONS AI LENS CONNECTIONS 1 Control coil negative (-) Not used 2 Control coil positive (+) Lens positive supply 3 Drive coil positive (+) Video drive signal 4 Drive coil negative (-) Ground Figure 2.
[ 8 ] Pelco Manual C1982M-A (12/00) POWER AND VIDEO CONNECTIONS T o connect the camera power and video do the following: 1. Remove the rear cover from the camera (refer to Figure 1).
Pelco Manual C1982M-A (12/00) [ 9 ] Table A. Recommended Wire Gauge and Wiring Distances The following are the recommended maximum distances for 24 V AC applications and are calculated with a 10-percent voltage drop. (T en percent is generally the maximum allowable voltage drop for AC-powered devices.
[ 10 ] Pelco Manual C1982M-A (12/00) LENS SETUP AND FOCUS PR OCEDURES Video Drive Auto Iris Lens When a video drive auto iris lens is used, the lens mode selector switch must be set to AI. Switch the EI and AGC OFF . Refer to the lens instructions and adjust the lens for the optimum picture (video out- put level of 1V peak-to-peak).
Pelco Manual C1982M-A (12/00) [ 11 ] BACK FOCUS ADJUSTMENT The back focus adjustment is located at the front of the camera and is accessible from either side of the case. T o adjust the back focus: 1. Loosen the two back focus locking screws (one on each side).
[ 12 ] Pelco Manual C1982M-A (12/00) SWIT CH SETTINGS Figure 7. Switch Settings 10 LL/INT Synchronization Selection Locks the frame rate to the power supply frequency . Eliminates vertical roll caused by multiple cameras connected to the same switching de- vice.
Pelco Manual C1982M-A (12/00) [ 13 ] 4 EI ON/EI OFF (Electronic Iris) The EI (Electronic Iris) feature compensates for an excessive light level by automatically adjusting shutter speed. When the EI is ON, the DD lens level potentiometer on the side of the camera may be used to adjust the EI threshold level.
[ 14 ] Pelco Manual C1982M-A (12/00) CAMERA PHASE ADJUSTMENT When using one AC power supply in a multi camera system, a brief vertical roll may occur on the monitor each time a camera view is switched. T o eliminate vertical roll, adjust the phase control to synchronize (line-lock), the cameras to one another .
Pelco Manual C1982M-A (12/00) [ 15 ] SPECIFICA TIONS GENERAL CCD Sensor: 1/3-inch Synchronization System: AC line lock or internal oscillator Horizontal Resolution MC3500S-2: 380 TV lines MC3600H-2: 570 TV lines Iris Control: Electronic/passive Minimum Illumination MC3500S-2: 0.
[ 16 ] Pelco Manual C1982M-A (12/00) Pelco, the Pelco logo, Camclosure, Esprit, Genex, Legacy, and Spectra are registered trademarks of Pelco. Endura and ExSite are trademarks of Pelco. HyperHAD and EXview HAD CCD are trademarks of the Sony Corporation.
An important point after buying a device Pelco MC3600H-2 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Pelco MC3600H-2 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Pelco MC3600H-2 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Pelco MC3600H-2 you will learn all the available features of the product, as well as information on its operation. The information that you get Pelco MC3600H-2 will certainly help you make a decision on the purchase.
If you already are a holder of Pelco MC3600H-2, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Pelco MC3600H-2.
However, one of the most important roles played by the user manual is to help in solving problems with Pelco MC3600H-2. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Pelco MC3600H-2 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
