Instruction/ maintenance manual of the product IS210 Pelco
Go to page of 24
INST ALLA TION C3428M-A (1/08) IS210 Series Camclosure ® Integrated Camera Sy stem.
.
C3428M-A (1/08) 3 Contents Important Safety Ins tructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Regulatory Notices . . . . . . . . . . . . . . . . . . . . . . . . . . .
4 C3428M-A (1/08) Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not block any ventilation openings. Install in accordance with the manufacturer’ s instructions.
C3428M-A (1/08) 5 REGULATORY NOTICES This device complies with Part 15 of the FCC Rules. O peration is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
6 C3428M-A (1/08) Description The IS210 Series Camclosure ® is a wedge-style integrate d camera system that is quick and easy to install. The system is designed to mount directly to a wall or ceiling, or to a corner with the IS210-CM corner mount. The IS210 system is shipped fully a ssembled.
C3428M-A (1/08) 7 Installation PREPARE MOUNTING SURFACE 1. Remove the cover of the IS210. Use the screwdriver bit (supplied) to loosen the three tamperproof screws, and then lift the cover from the base. 2. Remove the camera assembly from the base by removing the Phillips screws on each side of the camera assembly (refer to Figure 2).
8 C3428M-A (1/08) Figure 3. Fixed Mounting Pattern Figure 4. Adjustable Mounting Patter n FIXED MOUNTING PATTERN ADJU S TABLE MOUNTING PATTERN.
C3428M-A (1/08) 9 INSTALL BASE WITHOUT CONDUIT 1. Pull the power and video wiring for the camera through the mounting surface and then through the wiring hole in the mounting plate. Fasten the mounting plate to the mounting surface with # 8 stainless steel screws (not supplied) of the appropriate length.
10 C3428M-A (1/08) Figure 5. Removing the Wiring Plug 4. Insert the hole plug (supplied) into the hole in the base of the Camclosure (refer to Figure 6). Figure 6. Installin g the Hole Plug 5. Pull the wiring through the conduit opening (refer to Figure 7 on page 11): a.
C3428M-A (1/08) 11 Figure 7. Removing th e Conduit Cover 6. Install a 0.75-inch (1.91 cm) conduit connector in the conduit opening. Line up the mounting holes in the base with the mounting holes o f the mounting pl ate. Attach the base to the mounting plate with the three 8-32 x 0.
12 C3428M-A (1/08) REINSTALL CAMERA MODULE Reinstall the camera module (refer to Figure 8). Make sure the top of the camera is oriented properly; the lens housing contains a label that reads TOP . NOTE: T o prevent damage to the camera or lens, install the camera in the correct hole positions of the mounting bracket.
C3428M-A (1/08) 13 DN/CH SERIES ADJUSTMENTS Refer to Figure 10 to adjust the IS210-DN or IS210-CH model. Figure 10. Adjusting the IS210-DN/C H Series Camclosure SWITCH SETTINGS Locate the DIP switch.
14 C3428M-A (1/08) SW4-4: Flickerless In certain lighting conditions, a flicker in the light source may affect camera operation. Flic kering can be caused by a number of conditions, including the qua lity of the source power and the age and type of fluorescent bulbs and ballasts.
C3428M-A (1/08) 15 Adjusting V ertical Phase Y ou may need two people when synchronizing the cameras: one at the camera, the other at the monitor to observe the vertical roll and the effect of any camera adjustments. T o synchronize the cameras: 1. Choose a reference camera to which all other cameras will be phased.
16 C3428M-A (1/08) DAY/NIGHT OPERATION NOTE: This section only applies to DN model cameras. DN model cameras regularly check the brightness level of the field of view t o determine when to switch between day (color) and nig ht (black-white) operation.
C3428M-A (1/08) 17 DW/CW SERIES (WIDE DYNAMIC RANGE) ADJUSTMENTS Refer to Figure 12 to adjust the IS210-DW or IS210-CW model. Figure 12. Adjusting the IS210-DW/C W Series Camclosure SWITCH SETTINGS Locate the DIP switch. Then set the switches for your installation.
18 C3428M-A (1/08) SW1-4: Auto White Balance/Ma nual White Balance Auto white balance (AWB) is enabled by default (ON). T o manually set and lock the white balance: 1. Set SW1-4 to ON. 2. Hold a white background in front of the lens until the vide o is all white.
C3428M-A (1/08) 19 SW1-8: Day/Night Operation (DW models o nly) NOTE: On CW models, SW1-8 is unused and does not affect camera operation. DW model cameras regularly check the brightness level of the field of view to determine when to switch between day (color) and nig ht (black-white) operation.
20 C3428M-A (1/08) AUTO IRIS LEVEL ADJUSTMENT The electronics of the IS210-DW and IS210-CW Series Camclosures automatically adjust the camera to the auto iris. Auto iris level adjustments are n ot necessary . V ERTICAL PHASE ADJUSTMENT NOTE: Use this procedure for 24 V AC operation only .
C3428M-A (1/08) 21 Service Connector The IS210 Series Camclosure integrated camera system includes a service connector that outputs ca mera video. Use it at the installation site to set up the field of view and focus the camera.
22 C3428M-A (1/08) Specifications GENERAL Pan/T ilt Adjustment Manual Pan 180° T ilt 180° Construction Aluminum base and cover , steel camera mounting bracket Finish Gray polyester powder coa t Envi.
PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merc handise proved defective in materi al or workmanship for a period of one year after the da te of shipment.
Worl dwide Headquarters 3500 Pelco W ay Clovis, California 93612 USA USA & Canada T el: 800/289-9100 Fax: 800/289-9150 International T el: 1-559/292-1981 Fax: 1-559/348-1120 www .
An important point after buying a device Pelco IS210 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Pelco IS210 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Pelco IS210 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Pelco IS210 you will learn all the available features of the product, as well as information on its operation. The information that you get Pelco IS210 will certainly help you make a decision on the purchase.
If you already are a holder of Pelco IS210, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Pelco IS210.
However, one of the most important roles played by the user manual is to help in solving problems with Pelco IS210. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Pelco IS210 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
