Instruction/ maintenance manual of the product IS150 Pelco
Go to page of 12
Addendum IS90/IS110/IS150 Series Camclosure ® C3438M (5/07).
2 C3438M (5/07) Introduction This addendum updates the camera adjustment sections in the IS90, IS110, and IS1 50 Series Camclosure ® Installation manuals.
C3438M (5/0 7) 3 DN/CH/C Series Adjustments Refer to Figure 1 to adjust IS90-DN/CH/C models. Refer to Figure 2 to adjust IS110-DN/CH or IS150-DN/CH models.
4 C3438M (5/07) SWITCH SETTINGS Locate the DIP switch. Then set the switches for your installation. SW4-1: AGC (Auto Gain Control) The AGC (automatic gain control) adjusts the image automatically to compensate for changes in light levels. Set to ON to enable AG C.
C3438M (5/0 7) 5 AUTO IRIS LEVEL ADJUSTMENT T o adjust the auto iris DC-drive level (refer to Figure 1 or Figure 2 on page 3): 1. T ilt or rotate the camera module until you can access the auto iris level control (R19). 2. T urn the screw clockwise to increase the brig htness level or counterclockwise to decrease the brightness level.
6 C3438M (5/07) T o manually correct defective pixels (r efer to Figure 1 or Figure 2 on page 3): 1. Cover the lens completely . Make sure no light can enter the lens. NOTE: The mechanical iris lens aperture does not completely block the light. 2. Press and hold button SW3 for one second.
C3438M (5/0 7) 7 DW/CW Series (Wide Dy namic Range) Adjustments Refer to Figure 4 to adjust IS90-DW/CW models. Refer to Figure 5 to adjust IS110-DW/CW or IS150-DW/CW models.
8 C3438M (5/07) SWITCH SETTINGS Locate the DIP switch. Then set the switches for your installation. SW1-1: Video Format Set to ON for NTSC. Set to OFF for PAL. The default is ON. SW1-2: Line Sync When multiple cameras are connected to the same sw itching device, vertical roll may occur on the monitor .
C3438M (5/0 7) 9 SW1-7: DSS (Digital Slow Shutter) The default shutter speed for NTSC is 30 frames per sec ond (fps). It is 25 fps for P AL. This is also known as SENS 2X. Y ou can decrease the shutter speed to 7.5 fps (NTSC) or 6.25 fps (P AL). This is known as SENS 8X, which improves low light sensitivity .
10 C3438M (5/07) AUTO IRIS LEVEL ADJUSTMENT The electronics of the IS90-DW and IS90-CW Series Ca mclosure s automatically adjust the camera to the auto iris. Au to iris level adjustments are not necessary . V ERTICAL PHASE ADJUSTMENT NOTE: Use this procedure for 24 V AC operation only .
PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merc handise pr oved defective in mate rial or work manship for a period of one year after the date of shipment.
Worl dwide Headquarters 3500 Pelco W ay Clovis, California 93612 USA USA & Canada T el: 800/289-9100 Fax: 800/289-9150 International T el: 1-559/292-1981 Fax: 1-559/348-1120 www .
An important point after buying a device Pelco IS150 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Pelco IS150 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Pelco IS150 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Pelco IS150 you will learn all the available features of the product, as well as information on its operation. The information that you get Pelco IS150 will certainly help you make a decision on the purchase.
If you already are a holder of Pelco IS150, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Pelco IS150.
However, one of the most important roles played by the user manual is to help in solving problems with Pelco IS150. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Pelco IS150 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
