Instruction/ maintenance manual of the product ICS210 Pelco
Go to page of 20
® INST ALLA TION ICS210 Series Camclosure ® Integrated Camera System C2491M-C (1/06).
2 C2491M-C 1/06 Contents Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Regulatory Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
C2491M-C (1/06) 3 Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not block any ventilation openings. Install in accordance with the manufacturer’ s instructions.
4 C2491M-C (1/06) Regulatory Notices This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
C2491M-C (1/06) 5 Description The ICS210 Series Camclosure ® is a wedge style integrated camera system that is quick and easy to install. The system is designed to mount directly to a wall or ceiling, or to a corner with the ICS210- CM corner mount. ICS210 system is shipped fully assembled.
6 C2491M-C (1/06) Installation PREPARE MOUNTING SURFACE 1. Remove the cover of the ICS210. Use the screwdriver bit that is provided to loosen the three tamperproof screws, and then lift the cover from the base. 2. Remove the camera assembly from the base by removing the Phillips screws on each side of the camera assembly (refer to Figure 2).
C2491M-C (1/06) 7 4. Select a fixed or adjustable mounting pattern (refer to Figure 3 and Figure 4). Using the mounting plate as a template, mark the wire feedthrough and fastener hole positions on the mounting surface. Prepare the holes for the installation.
8 C2491M-C (1/06) INSTALL BASE WITHOUT CONDUIT 1. Pull the power and video wiring for the camera through the mounting surface and then through the wiring hole in the mounting plate. Fasten the mounting plate to the mounting surface with #8 stainless steel screws (not provided) of the appropriate length.
C2491M-C (1/06) 9 3. Using a blunt tool push out the wiring plug in the bottom of the base (refer to Figure 6). Pull the wiring inside the base. Figure 6. Removing the Wiring Plug 4. Insert the hole plug that is supplied into the hole in the base of the Camclosure (refer to Figure 7).
10 C2491M-C (1/06) 6. Install a 3/4-inch (1.91 cm) conduit connector in the conduit opening. Line up the mounting holes in the base with the mounting holes of the mounting plate. Attach the base to the mounting plate with the three 8-32 x 0.375-inch screws and lock washers previously removed.
C2491M-C (1/06) 11 ADJUST POSITION 1. T urn on power to the camera and monitor . 2. V arifocal lens only: Loosen the focal length and focus locking screws (refer to Figure 9). Adjust according to scene detail. Retighten the screws. Figure 9. V arifocal Lens Adjustment 3.
12 C2491M-C (1/06) Adjustments (Color Camera Only) If you have a color camera, it is set up at the factory and normally requires no adjustments. Sometimes, however , adjustments may be necessary. 1. Remove the cover using the supplied 1/8-inch hollow screwdriver bit.
C2491M-C (1/06) 13 AUTO IRIS LEVEL ADJUSTMENT If you have a varifocal lens or fi xed focal length lens with an auto iris, you can adjust the iris level setting to increase or decrease brightness. Figure 11. Iris Level Adjustment FOCUS ADJUSTMENT FOR FIXED FOCAL LENGTH LENS WITH AUTO IRIS T o adjust the focus, do the following: 1.
14 C2491M-C (1/06) HEATER BOARD REMOVAL T o remove the heater board, do the following: 1. Disconnect the four -pin heater connector (red, orange, and black wires) if it is plugged in. Figure 13. Removing Heater Board 2. Wait for the heater elements to cool if they are hot.
C2491M-C (1/06) 15 SWITCH SETTINGS FOR FIXED FOCAL LENGTH LENS WITH AUTO IRIS Refer to Figure 14. The switch is located next to the lens. Automatic backlight compensation (factory setting) is used under varying lighting conditions (such as outdoors) or fi xed lighting conditions where there are no bright spots that darken other picture details.
16 C2491M-C (1/06) SWITCH SETTINGS FOR V ARIFOCAL LENS The high resolution camera with varifocal lens and auto iris is confi gured at the factory for automatic exposure. Figure 16. Switch Settings for Varifocal Lens For manually setting and locking the white balance Place a white background in front of camera and turn off switch 1.
C2491M-C (1/06) 17 Specifications General Pan/T ilt Adjustment Manual; 5° above horizontal to 20° below horizontal tilt; 24° pan adjustment when using the adjustable mounting pattern in base Ratin.
PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment. Exceptions to this warranty are as noted below: • Five years on FT/FR8000 Series fiber optic products.
REVISION HISTORY Manual # Date Comments C2491M 6/05 Orginal version. C2491M-A 7/05 Revised per new camera shell design for varifocal lens. C2491M-B 10/05 Revised switch-setting descriptions for varifocal lens. C2491M-C 1/06 Revised factory switch settings for varifocal lens.
Worldwide Headquarters 3500 Pelco Way Clovis, California 93612 USA USA & Canada T el: 800/289-9100 Fax: 800/289-9150 International T el: 1-559/292-1981 Fax: 1-559/348-1120 www.
An important point after buying a device Pelco ICS210 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Pelco ICS210 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Pelco ICS210 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Pelco ICS210 you will learn all the available features of the product, as well as information on its operation. The information that you get Pelco ICS210 will certainly help you make a decision on the purchase.
If you already are a holder of Pelco ICS210, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Pelco ICS210.
However, one of the most important roles played by the user manual is to help in solving problems with Pelco ICS210. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Pelco ICS210 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
