Instruction/ maintenance manual of the product ES31C Pelco
Go to page of 68
ES30C/ES31C Series Esprit ® with IOP INSTALLATION/OPERATION C307M-I (11/05).
.
C307M-I (11/05) 3 Contents Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Regulatory Notices .
4 C307M-I (11/05) IR Filter Mode (Models ES30CBW18/ES31CBW18/ES30CBW24/ES31CBW24) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Limit Stops . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
C307M-I (11/05) 5 Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not block any ventilation openings. Install in accordance with the manufacturer’ s instructions.
6 C307M-I (11/05) Regulatory Notices This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
C307M-I (11/05) 7 Description The ES30C and ES31C Series combine a receiver , pan and tilt, enclosure, and Integrated Optics Package (IOP) in a single, easy-to-install system. The Integrated Optics Package contains an auto-focus camera and lens module with programmable features.
8 C307M-I (11/05) Installation 1. When installing the ES30C/ES31C Esprit ® system, allow for sufficient clearance between the top of the unit and overhead obstructions. This will prevent interference when the enclosure is driven to its maximum elevation of 33 degrees.
C307M-I (11/05) 9 4. Route the wires and cables through the center of the Esprit mount. Reinstall the transformer module into the base. The transformer module can be positioned in the mount base in only one orientation. 5. ES30C-5/ES31C-5 Models Only: Set the 120/230 voltage selector switch on the transformer to the appropriate voltage.
10 C307M-I (11/05) 7. Install mount; refer to the installation manual supplied with the mount for instructions. 8. T urn on the power . If the red LED lights, turn off the power and proceed to the next step. If the red LED does not light, refer to the T roubleshooting section.
C307M-I (11/05) 11 TXB Series T ranslator Board Installation (Optional) Pelco’ s TXB Series allows controllers from other companies to communicate with the Esprit system.
12 C307M-I (11/05) HOW TO REINSTALL THE PAN AND T ILT COVER The pan and tilt covers must be properly seated and have a tight seal all the way around when installed. T o reinstall the pan and tilt cover , do the following: 1. Properly position the cover and slide it into place.
C307M-I (11/05) 13 Operation POWER -UP DISPLAY When the system is powered up, the selected protocol, revision number , and other information is displayed on the monitor . For example, the screen might show the following information: The information displayed depends on the selected protocol (C, D, or P) and the menu selection for power -up mode.
14 C307M-I (11/05) OPERATING NOTES ENVIRONMENTAL RANGE The operating temperature ranges from a minimum of -50°F (-45°C) to a maximum of 122°F (50°C) for sustained system operation or 140°F (60°C) absolute maximum. The entire unit can de-ice and be operational in two hours from a temperature of -13°F (-25°C).
C307M-I (11/05) 15 PATTERNS The Esprit system can do either one full pattern (1.5, 3, or 6 minutes long) or two half patterns (.75, 1.5, or 3 minutes long). This pattern can consist of any standard pan and tilt or lens command. Presets, flip, digital zoom, proportional pan, and turbo are not allowed in a pattern.
16 C307M-I (11/05) Programming – ES30C16/ES31C16 Backlight comp Off Zoom limit x- - Reset camera <Gain/AGC> <Auto iris> Next Exit Camera Menu Line Sync On Line Sync Phase 0 Exit Line Syn.
C307M-I (11/05) 17 Programming – ES30C22/ES31C22 Backlight comp Off Zoom limit x- - Reset camera <Gain/AGC> <Auto iris> Next Exit Camera Menu Line Sync On Line Sync Phase 0 Exit Line Syn.
18 C307M-I (11/05) Programming – ES30CBW18/ES31CBW18/ES30CBW24/ES31CBW24 Backlight comp Off Zoom limit x72 Reset camera <Gain/AGC> <Auto iris> Next Exit Camera Menu Line Sync On Line Syn.
C307M-I (11/05) 19 Programming ACCESSING MAIN MENU (PRESET 95) Y ou can call up the main menu on your monitor by programming (setting or creating) preset 95 (28 if in 32-preset mode). Programming preset 95 for Pelco’ s controllers varies according to the type of controller you are using.
20 C307M-I (11/05) CM9740/CM9760/CM9770 1. Press the ESCAPE key to open the Main menu. Select DEF . The Define Menu appears. 2. Enter your four -digit PIN if this is your first time entering this mode. 3. Enter 95 and select PRST . The main menu appears on the monitor .
C307M-I (11/05) 21 AUTO FOCUS MODE There are two auto focus modes: Auto: If auto focus is in the auto mode, pressing the Focus Far or Focus Near button will place the focus in the manual mode. The system will return to auto focus if you pan or tilt the unit or do a zoom function.
22 C307M-I (11/05) AUTO IRIS The following are the settings for auto iris: Mode Level Peak T o change the settings for auto iris: 1. Program preset 95 (28). The main menu appears. 2. Position the cursor (>) beside Camera. 3. Press the Iris Open button to enter the Camera menu.
C307M-I (11/05) 23 AUTO IR LEVEL (MODELS ES30CBW18/ES31CBW18/ES30CBW24/ES31CBW24) The auto IR level is the light level at which the infrared filter switches IN or OUT . Following are the available settings for the Auto IR Level: Dusk (default): approximately 6 lux (black-white) approximately 13 lux (color) Dark: approximately 0.
24 C307M-I (11/05) AUTO SHARPNESS The following settings are available for auto sharpness: On: Automatically sets the sharpness of the camera. Off: The sharpness of the camera needs to be manually set (refer to Sharpness). T o change the mode: 1. Program preset 95 (28).
C307M-I (11/05) 25 AZ/EL Az/El programs the horizontal display position of the Azimuth 1 /Elevation 2 label. NOTE: Az/El display is not available while you are programming or running a pattern. The following settings are available for the Az/El label: Off: Label is not displayed.
26 C307M-I (11/05) AZ/EL LINE Az/El Line controls the vertical display position of the Azimuth/Elevation label. The label may be displayed on lines 3 through 10. Line 3 is the third line from the top of the screen and line 10 is located at the bottom of the screen.
C307M-I (11/05) 27 AZIMUTH ZERO Azimuth is the pan angle from 0° to 359°. Azimuth zero is the programmed 0° point that is normally set to magnetic north. Once programmed, on-screen pan position (azimuth) and compass readings are based on the set azimuth zero point.
28 C307M-I (11/05) BACKLIGHT COMPENSATION There are two backlight compensation modes: On: The system uses the center 10 percent of the picture to adjust the iris. If there is a bright light source outside of this area, it will wash out to white. The camera will adjust the iris so that the object in the sensitive area is properly exposed.
C307M-I (11/05) 29 DIRECTION Direction programs the horizontal display position of the Direction label (N, NW , NE, …). NOTES: • For direction to be accurate, the azimuth zero must be set to magnetic north. • Direction display is not available while you are programmming or running a pattern.
30 C307M-I (11/05) DIRECTION LINE Direction Line controls the vertical display position of the Direction label. The label may be displayed on lines 3 through 10. Line 3 is the third line from the top of the screen and line 10 is located at the bottom of the screen.
C307M-I (11/05) 31 DISPLAY DURATION Display Duration programs the duration the Az/El, Direction, and Zoom labels are displayed on the monitor . The available settings for display duration include the following: Constant: The label is displayed continuously .
32 C307M-I (11/05) GAIN/AGC GAIN LIMIT The gain limit sets the maximum level for the automatic gain control. Increasing the level will increase the signal level and increase the noise level of the picture. T o change the gain: 1. Program preset 95 (28).
C307M-I (11/05) 33 IR FILTER MODE (MODELS ES30CBW18/ES31CBW18/ES30CBW24/ES31CBW24) There are two settings for the IR filter mode: Auto: IR filter switches in and out automatically . NOTES: • Automatic shutter speed must be set to Auto for the IR filter to operate automatically .
34 C307M-I (11/05) LIMIT STOPS NOTE: Limit stops are inactive while setting items in the program menu (e.g. azimuth zero, scan limits, manual pan limits). T URNING LIMIT STOPS ON OR OFF T o change the limit stop mode: 1. Program preset 95 (28). The main menu appears.
C307M-I (11/05) 35 Limit Stops Menu The manual pan limit stops can be set at the controller using the Limit Stops menu: 1. Program preset 95 (28). The main menu appears. 2. Position the cursor (>) beside Limit Stop. 3. Press the Iris Open button to enter the Limit Stop menu.
36 C307M-I (11/05) Limit Stops Menu The manual pan limit stops can be set at the controller using the Limit Stops menu: 1. Program preset 95 (28). The main menu appears. 2. Position the cursor (>) beside Limit Stop. 3. Press the Iris Open button to enter the Limit Stop menu.
C307M-I (11/05) 37 LINE SYNCHRONIZATION If cameras are out of phase with each other , they may produce what appears to be vertical roll when switching between cameras. There are two settings for line synchronization: On: Adjust the synchronization of the power line voltage so that it is in phase with other cameras.
38 C307M-I (11/05) LOWLIGHT LIMIT (MODELS ES30C22/ES31C22, ES30CBW18/ES31CBW18, AND ES30CBW24/ES31CBW24) This setting determines the maximum length of time the shutter will remain open automatically in low light conditions.
C307M-I (11/05) 39 PARK T IME MINUTES This feature causes the system to park at preset 1 after a programmed number of minutes of control inactivity . The time can be set from 1 minute to 720 minutes (12 hours), or it can be set to zero, which disables this feature.
40 C307M-I (11/05) PATTERN LENGTH The Esprit can do the following: One full pattern - 1.5, 3, or 6 minutes long or T wo half patterns - .75, 1.5, or 3 minutes long This pattern can consist of any standard pan, tilt, or lens command. Presets, flip, and turbo are not allowed in a pattern.
C307M-I (11/05) 41 POWER -UP MODE This feature lets the dome resume a desired condition following power -up. The menu includes the following choices. Default: On power -up, the system goes through a configuration cycle and stops at zero reference, showing “Configuration Done,” address, and mode settings on the screen.
42 C307M-I (11/05) PROPORTIONAL PAN There are two proportional pan modes: On: Enables the proportional pan mode. The amount of zoom controls the pan and tilt. At telephoto zoom settings, the pan and tilt speeds will be slower for a given amount of joystick deflection than at wide zoom settings.
C307M-I (11/05) 43 RESET CAMERA Resetting the camera returns the settings to their defaults. T urning off power does not reset the camera. Camera settings are retained in memory . When the power is turned back on, the settings will be the same as they were when the power was turned off.
44 C307M-I (11/05) SCAN SPEED The scan speed is adjustable from 1-40 degrees per second. This occurs in three scan modes: auto, random, and frame scan. T o change the scan speed: 1. Program preset 95 (28). The main menu appears. 2. Position the cursor (>) beside Other .
C307M-I (11/05) 45 SHARPNESS Use the Sharpness setting to manually set the sharpness of the camera. T o manually set the sharpness of the camera: 1. Program preset 95 (28). The main menu appears. 2. Position the cursor (>) beside Camera. 3. Press the Iris Open button to enter the Camera menu.
46 C307M-I (11/05) SHUTTER SPEED There are several electronic shutter speed settings: Auto 1/2 1/4 1/8 1/15 1/30 1/60 1/120 1/180 1/250 1/500 1/1000 1/2000 1/4000 1/10,000 1/30,000 In the Auto setting the camera controls the shutter speed automatically .
C307M-I (11/05) 47 SPEED PROFILE This feature allows the operator to set the wind speed conditions for the location of the Esprit system. Y ou can set two wind speed profiles of 50 mph or 90 mph in which the system will remain operational. In both settings, the pan speed will be a maximum of 40 degrees per second.
48 C307M-I (11/05) WHITE BALANCE The settings for white balance are as follows: Auto white bal R Gain B Gain T o change the white balance settings: 1. Program preset 95 (28). The main menu appears. 2. Position the cursor (>) beside Camera. 3. Press the Iris Open button to enter the Camera menu.
C307M-I (11/05) 49 WIPER MODE There are three wiper settings: Wiper Mode Wiper Dwell Wiper T ime T o change the wiper settings: 1. Program preset 95 (28). The main menu appears. 2. Position the cursor (>) beside Wiper . 3. Press the Iris Open button to enter the Wiper menu.
50 C307M-I (11/05) ZONE BLANK The Esprit system features onscreen programmable zone blanking. This feature lets you define any zone as blanked for video (viewing/recording). Zones can be programmed to overlap each other , although this is not recommended.
C307M-I (11/05) 51 ZOOM Zoom programs the horizontal display position of the Zoom label. The following settings are available for the Zoom label: Off: Label is not displayed. Left: Label is displayed on the left-hand side of the screen. Center (default): Label is displayed in the center of the screen.
52 C307M-I (11/05) ZOOM LIMIT ES30C16/ES31C16: 16X optical zoom and 10X electronic zoom, can be set for 16X, 32X, 64X, 128X, or 160X. ES30C22/ES31C22: 22X optical zoom and 10X electronic zoom, can be set for 22X, 32X, 88X, 176X, or 220X. ES30CBW18/ES31CBW18: 23X optical zoom and 10X electronic zoom, can be set for 23X, 32X, 92X, 184X or 230X.
C307M-I (11/05) 53 ZOOM LINE Zoom Line controls the vertical display position of the Zoom label. The label may be displayed on lines 3 through 10. Line 3 is the third line from the top of the screen and line 10 is located at the bottom of the screen. Line 10 is the default setting.
54 C307M-I (11/05) T roubleshooting Symptom: System does not operate. 1. Check system input voltage. 2. The Esprit system is protected by a resettable overcurrent protective device located in the transformer module.
C307M-I (11/05) 55 Symptom: No video or poor video 1. Check the video and power connections to the camera. 2. Check for power to the camera from the Esprit system camera power output. 3. Check all coax BNC connectors from the camera to the monitor . 4.
56 C307M-I (11/05) APPENDIX NOTE: Esprit will sense and automatically select input from Coaxitron control signals in either the standard or extended mode. Therefore, the DIP switches settings have no effect on Coaxitron control signals. *SW1-3 is not used; set it in the OFF position.
C307M-I (11/05) 57 NOTE: The Esprit will sense and automatically select input from Coaxitron control signals in either the standard or extended mode. Therefore, the DIP switches settings have no effect on Coaxitron control signals. T able B. Switch Settings for SW2 (P-T ype Control) T able C.
58 C307M-I (11/05) 25 ON OFF OFF ON ON OFF OFF OFF 26 OFF ON OFF ON ON OFF OFF OFF 27 ON ON OFF ON ON OFF OFF OFF 28 OFF OFF ON ON ON OFF OFF OFF 29 ON OFF ON ON ON OFF OFF OFF 30 OFF ON ON ON ON OFF .
C307M-I (11/05) 59 74 OFF ON OFF ON OFF OFF ON OFF 75 ON ON OFF ON OFF OFF ON OFF 76 OFF OFF ON ON OFF OFF ON OFF 77 ON OFF ON ON OFF OFF ON OFF 78 OFF ON ON ON OFF OFF ON OFF 79 ON ON ON ON OFF OFF O.
60 C307M-I (11/05) 123 ON ON OFF ON ON ON ON OFF 124 OFF OFF ON ON ON ON ON OFF 125 ON OFF ON ON ON ON ON OFF 126 OFF ON ON ON ON ON ON OFF 127 ON ON ON ON ON ON ON OFF 128 OFF OFF OFF OFF OFF OFF OFF.
C307M-I (11/05) 61 172 OFF OFF ON ON OFF ON OFF ON 173 ON OFF ON ON OFF ON OFF ON 174 OFF ON ON ON OFF ON OFF ON 175 ON ON ON ON OFF ON OFF ON 176 OFF OFF OFF OFF ON ON OFF ON 177 ON OFF OFF OFF ON ON.
62 C307M-I (11/05) 221 ON OFF ON ON ON OFF ON ON 222 OFF ON ON ON ON OFF ON ON 223 ON ON ON ON ON OFF ON ON 224 OFF OFF OFF OFF OFF ON ON ON 225 ON OFF OFF OFF OFF ON ON ON 226 OFF ON OFF OFF OFF ON O.
C307M-I (11/05) 63 Specifications ELECTRICAL Input V oltage 24, 120, or 230 V AC, 50/60 Hz; switch selectable for 120/230 VAC inputs. Reset feature enabled when power becomes unstable or interruped.
64 C307M-I (11/05) Zoom Ratio ES30C16/ES31C16 16X optical zoom, 10X electronic zoom ES30CBW18/ES31CBW18 23X optical zoom, 10X electronic zoom ES30C22/ES31C22 22X optical zoom, 10X electronic zoom ES30.
C307M-I (11/05) 65 NOTE: V A LUES IN PARENTHESES ARE CENTIMETERS; ALL OTHERS ARE INCHES. 5.2 (13.3) 13.3 (33.9) 3.9 (9.9) 14.6 (37.0) 9.8 (24.9) 3.6 (9.
66 C307M-I (11/05).
PRODUCT WARRANTY AND RETURN INFORMA TION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment. Exceptions to this warranty are as noted below: • Five years on FT/FR8000 Series fiber optic products.
W orldwide Headquarters 3500 Pelco W ay Clovis, California 93612 USA USA & Canada T el: 800/289-9100 Fax: 800/289-9150 International T el: 1-559/292-1981 Fax: 1-559/348-1120 www .
An important point after buying a device Pelco ES31C (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Pelco ES31C yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Pelco ES31C - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Pelco ES31C you will learn all the available features of the product, as well as information on its operation. The information that you get Pelco ES31C will certainly help you make a decision on the purchase.
If you already are a holder of Pelco ES31C, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Pelco ES31C.
However, one of the most important roles played by the user manual is to help in solving problems with Pelco ES31C. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Pelco ES31C along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
