Instruction/ maintenance manual of the product ERD2000 Pelco
Go to page of 16
IRD/ERD2000 Series Receiver C1506M-A (8/02) ® INST ALLA TION/OPERA TION.
2 C1506M-A (8/02).
C1506M-A (8/02) 3 CONTENTS Section Page IMPORT ANT SAFEGUARDS AND WARNINGS ..................................................................................... 4 DESCRIPTION ............................................................................
4 C1506M-A (8/02) 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not block any ventilation openings.
C1506M-A (8/02) 5 The IRD/ERD2000 Series Receiver operates Pelco’ s fixed speed pan/tilts and domes. The receiver works with standard and extended Coaxitron ® controllers, including the CM6700/ 7500/8500/9500, KBD9000, MPT9000/9008/9500, and MX4000.
6 C1506M-A (8/02) ERD2200 WIRING E N C L O S U R E POWER O U T L L N N GROUND STUD POWER TERMINALS M A I N POW E R IN Figure 2. ERD2200 Receiver Figure 3. ERD2200 Power Connections 1. Fuses are installed for 115 V AC operation. For 230 V AC operation, install the appropriate fuses (supplied).
C1506M-A (8/02) 7 A C A C 24V 50/60HZ INPUT POWER ~ 24V ~ 50/60HZ P/T POWER SELECT 115 /230V ~ 50/60HZ A C A C ERD OPTION TLC OUT VIDEO IN PWR CX LENS AUX1 AUX2 C N N OC 24V ,1A ~ I F Z C CAM PWR C C PA N/ T I LT 5V CLASS 2 WIRING ERD OPTIONS 11 5/230V 50/60Hz .
8 C1506M-A (8/02) IRD2024 WIRING 1. Connect power to the 24 V AC INPUT connector on the rear of the receiver . The receiver’ s power requirement is a maximum of 5 V A, not including the camera and pan/tilt. Refer to the pan/tilt manual for its power requirements.
C1506M-A (8/02) 9 When power is applied to the receiver , the green PWR LED on the receiver lights. Whenever the receiver gets a valid Coaxitron control signal, the green CX LED blinks.
10 C1506M-A (8/02) FUSE REPLACEMENT CAUTION: These service instructions are for use by qualified service personnel only . T o reduce the risk of electrical shock, do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so.
C1506M-A (8/02) 11 TROUBLESHOOTING Check the wiring connections. If the CX LED does not blink when commands are sent to the receiver , make sure the controller is working properly . Also check the video coaxial cable between the controller and the VIDEO OUT connection on the receiver .
12 C1506M-A (8/02) WIRING T ABLES Wire Gauge Table A. 24 VAC Wiring Distances Table The following are the recommended maximum wire distances (transformer to load) for 24 V AC applications and are calculated with a 10-percent voltage drop. (T en percent is generally the maximum allowable voltage drop for AC-powered devices.
C1506M-A (8/02) 13 SPECIFICA TIONS ERD2200 Electrical Input V oltage: 115/230 V AC, 50/60 Hz Output V oltage Camera: 24 V AC (or 115/230 VAC if using enclosure power) Lens: 8 VDC Pan/T ilt: 24/115/230.
14 C1506M-A (8/02) REGULA TORY NOTICES NOTE: This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
C1506M-A (8/02) 15 REVISION HISTORY Manual # Date Comments C1506M 3/00 Original version. C1506M-A 8/02 Revised manual per ECO #02-8195 to meet UL standards. Added FCC notice. W ARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment.
World Headquarters 3500 Pelco Way Clovis, California 93612 USA USA & Canada Tel: 800/289-9100 Fax: 800/289-9150 International Tel: 1-559/292-1981 Fax: 1-559/348-1120 www.
An important point after buying a device Pelco ERD2000 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Pelco ERD2000 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Pelco ERD2000 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Pelco ERD2000 you will learn all the available features of the product, as well as information on its operation. The information that you get Pelco ERD2000 will certainly help you make a decision on the purchase.
If you already are a holder of Pelco ERD2000, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Pelco ERD2000.
However, one of the most important roles played by the user manual is to help in solving problems with Pelco ERD2000. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Pelco ERD2000 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
