Instruction/ maintenance manual of the product eh8106l Pelco
Go to page of 12
C1420M-G (12/04) ® INSTALLATION/OPERATION EH8106L Legacy ® Pressurized Enclosure.
2 C1420M-G (12/04) Contents Important Safeguards and Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Description . .
C1420M-G (12/04) 3 Important Safety Instructions Prior to installation and use of this product, the following W ARNINGS should be observed. 1. Installation and servicing should be done only by qualified service personnel and conform to all local codes.
4 C1420M-G (12/04) Installation MOUNTING To attach the enclosure to the pan and tilt unit, perform the following installation steps. 1. Make sure the tilt shaft on the pan and tilt unit is near horizontal so that the connector in the tilt shaft is pointing upward.
C1420M-G (12/04) 5 Figure 1. EH8106L Enclosure - Rear View Figure 2. EH8106L Enclosure - Wiring Diagram SCHRAEDER VA LV E SPIRAL RET AINING SPRING RET AINING SPRING END PRESSURE RELIEF V AL VE T -HANDLE GROUND STUD AC NEUT AC LINE THERMOST A T HTR HTR PP ZOOM PP FOCUS PP COM PP +5V LENS COM ZOOM FOCUS IRIS PIN NO.
6 C1420M-G (12/04) MATING CONNECTOR ASSEMBLY To assemble the 16-pin mating connector , perform the following steps: 1. Discard the white plastic sleeve that is included with the connector assembly . Thread the cable through the compression nut/strain relief and connector shell.
C1420M-G (12/04) 7 RECHARGING THE ENCLOSURE Y ou may use your own charging equipment or Pelco’ s EH8000RKIT to recharge the enclosure. If you are using your own equipment, adjust the regulator for an output pressure of 12 psi (83 kPa).
8 C1420M-G (12/04) Servicing DISASSEMBLY 1. Disconnect the power from the enclosure. 2. Remove the mating connector from the rear of the enclosure by turning the outer ring counterclockwise until a click is felt; then pull the mating portion of the connector off.
C1420M-G (12/04) 9 Specifications Electrical Input V oltage 120 V AC (230 V AC optional) for heaters Power Requirements 160 watts Connector 16-pin jam nut receptacle Maximum Cable Distances 12 AWG 2,640 ft (804 m) 14 AWG 1,660 ft (505 m) 16 AWG 1,040 ft (316 m) 18 AWG 650 ft (198 m) 20 AWG 410 ft (124 m) Heater T wo 40 watt, 120 V AC.
10 C1420M-G (12/04) ENVIRONMENT AL Ambient Operating T emperature -40° to 122°F (-40° to 50°C) (with heater) Vibration 5 to 60 Hz with 0.082 inch total travel (15 g’ s at 60 Hz).
PRODUCT WARRANTY AND RETURN INFORMA TION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment.
® W orldwide Headquarters 3500 Pelco W ay Clovis, California 93612 USA USA & Canada T el: 800/289-9100 Fax: 800/289-9150 International T el: 1-559/292-1981 Fax: 1-559/348-1120 www .
An important point after buying a device Pelco eh8106l (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Pelco eh8106l yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Pelco eh8106l - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Pelco eh8106l you will learn all the available features of the product, as well as information on its operation. The information that you get Pelco eh8106l will certainly help you make a decision on the purchase.
If you already are a holder of Pelco eh8106l, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Pelco eh8106l.
However, one of the most important roles played by the user manual is to help in solving problems with Pelco eh8106l. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Pelco eh8106l along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
