Instruction/ maintenance manual of the product EH8100 Series Pelco
Go to page of 12
® INSTALLATION/OPERATION C1407M-G (12/04) EH8100 Series Pressurized Camera Enclosure.
2 C1407M-G (12/04) Contents Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Description .
C1407M-G (12/04) 3 Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions.
4 C1407M-G (12/04) Description Enclosures in the EH8100 Series are sealed and pressurized. They will accept CCD cameras with fixed focal length or motorized zoom lenses.
C1407M-G (12/04) 5 Figure 1. EH8100 Series Enclosure - Rear View Figure 2. EH8100 Series Enclosure - Wiring Diagram SCHRAEDER VALVE SPIRAL RETAINING SPRING RETAINING SPRING END PRESSURE RELIEF VALVE T.
6 C1407M-G (12/04) MATING CONNECTOR ASSEMBLY To assemble the 16-pin mating connector , perform the following steps: 1. Discard the white plastic sleeve that is included with the connector assembly . Thread the cable through the compression nut/strain relief and connector shell.
C1407M-G (12/04) 7 RECHARGING THE ENCLOSURE Y ou may use your own charging equipment or Pelco’ s EH8000RKIT to recharge the enclosure. If you are using your own equipment, adjust the regulator for an output pressure of 12 psi (83 kPa).
8 C1407M-G (12/04) Servicing DISASSEMBLY 1. Disconnect the power from the enclosure. 2. Remove the mating connector from the rear of the enclosure by turning the outer ring counterclockwise until a click is felt; then pull the mating portion of the connector off.
C1407M-G (12/04) 9 Specifications Electrical Input V oltage 120 V AC (230 VAC optional) for heaters Power Requirements 40 watts (EH8104) 80 watts (EH8106) Connector 16-pin receptacle with jam nut Mat.
10 C1407M-G (12/04) Environmental Ambient Operating T emperature -40° to 122°F (-40° to 50°C) (with heater) Vibration 5 to 60 Hz with 0.082-inch total travel (15 g’ s at 60 Hz).
PRODUCT WARRANTY AND RETURN INFORMA TION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment.
® W orldwide Headquarters 3500 Pelco W ay Clovis, California 93612 USA USA & Canada T el: 800/289-9100 Fax: 800/289-9150 International T el: 1-559/292-1981 Fax: 1-559/348-1120 www .
An important point after buying a device Pelco EH8100 Series (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Pelco EH8100 Series yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Pelco EH8100 Series - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Pelco EH8100 Series you will learn all the available features of the product, as well as information on its operation. The information that you get Pelco EH8100 Series will certainly help you make a decision on the purchase.
If you already are a holder of Pelco EH8100 Series, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Pelco EH8100 Series.
However, one of the most important roles played by the user manual is to help in solving problems with Pelco EH8100 Series. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Pelco EH8100 Series along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
