Instruction/ maintenance manual of the product EH66X Pelco
Go to page of 20
Pelco Manual C411M-D (1/96) 17 Pelco • 3500 Pelco Way, Clovis, CA 93612-5699 • USA • www.pelco.com (559) 292-1981 or (800) 289-9100 • FAX (559) 292-3827 or (800) 289-9150 EH66/EH66X Envir onme.
TABLE OF CONTENTS S ection P age 1.0 W ARNINGS ........................................................................................................................................ 1 2.0 SCOPE .......................................................
LIST OF ILLUSTRA TIONS F igur e P age 1 EH66/EH66X Dimension Dra wing ................................................................................................. 2 2 Wiring Diagram f or Windo w Defroster , Wiper/W asher and Blow er/Heater Assemblies .
This page intentionally left blank. iv Pelco Manual C411M-D (1/96).
Pelco Manual C411M-D (1/96) 1 Please thoroughly familiarize yourself with the information in this manual prior to installation and operation. This symbol indicates that dangerous voltage constituting a risk of electric shock is present within this unit.
2 Pelco Manual C411M-D (1/96) 2.0 SCOPE The information contained within this manual covers the EH66/EH66X Series environmental enclosure. 3.0 DESCRIPTION The EH66 Series is an all-weather environmental enclo- sure for 2/3" and 1" cameras with a maximum camera/ lens size of 7" W x 7" H x 22" L (17.
Pelco Manual C411M-D (1/96) 3 NOTE : Cameras with a low optical centerline or using a large diameter lens require an ele va- tion block (1 inch or 2 inch) for proper posi- tioning. See Section 8.0, Optional Accessories, for the correct model number . 3.
4 Pelco Manual C411M-D (1/96) Figure 2 . Wiring Diagram for Window Defroster, Wiper/Washer and Blower/Heater Assemblies to control.
Pelco Manual C411M-D (1/96) 5 4.3 FIXED ENCLOSURE MOUNTING The are two types of mounts that can be used with the EH66 enclosure: wall, or pedestal/ceiling (see Figures 3 and 4).
6 Pelco Manual C411M-D (1/96) 4.4 P AN/TIL T ENCLOSURE MOUNTING The EH66 enclosure can also be mounted to a pan/tilt assembly in addition to the wall or pedestal/ceiling mount. To include the pan/tilt assembly in your configuration, perform the following steps: 1.
Pelco Manual C411M-D (1/96) 7 4.5 WINDOW WIPER INST ALLA TION To install the window wiper kit, perform the following steps and refer to Figures 7 and 8: 1. Turn the EH66 enclosure over so the bottom is facing up. 2. If necessary, lay out the locations of the four (4) .
8 Pelco Manual C411M-D (1/96) 4.6 B66KIT/E624HB/H66KIT INST ALLA TION All heater and blower kits are supplied partially as- sembled. Install in the enclosure according to the fol- lowing instructions: 1.
Pelco Manual C411M-D (1/96) 9 Figure 9 . EH66 Enclosure Exploded Assembly Diagram 6.0 EXPLODED ASSEMBL Y DIAGRAMS See Figures 9 and 10 for exploded assembly diagrams of the EH66 enclosure and WW66, WW66-5/220 wiper assembly.
10 Pelco Manual C411M-D (1/96) Figure 10 . WW66, WW66-5/220 Wiper Exploded Assembly Diagram NOTE: FIGURE DOES NOT REPRESENT CURRENT PUMP IN USE..
Pelco Manual C411M-D (1/96) 11 7.0 MECHANICAL P ARTS LISTS 7.1 MECHANICAL AND ELECTRICAL PARTS LIST FOR EH66 ENCLOSURE Item No. Qty Description Part Number 1 4 Gasket, Window Frame EH110042 2 1 Gasket, Cable Entry EH110072 3 1 Plate, Cable Entry EH14231COMP 4 2 Gasket, Rim EH450010000 5 2 Gland, UL, PG-13.
12 Pelco Manual C411M-D (1/96) 7.2 MECHANICAL P ARTS LIST FOR WW66 AND WW66-5/220 WINDOW WIPER ASSEMBL Y Item No. Qty Description Part Number 1 3 Bearing 776003 2 1 Diode DIOPT40F 3 — Not used — 4 1 Switch SWIV3L 5 1 Spacer, 1/4" Hex x .6254-40 tap SPA8404 6 1 Transformer TRF21162.
Pelco Manual C411M-D (1/96) 13 8.0 OPTIONAL ACCESSORIES FACTORY INSTALLED EHRC Relay module for low voltage control of wiper/washer and camera on/off. Requires MEH24DT control module. TI66 Thermal insulation provides increased thermal protection for enclosure and contents at extreme temperatures (for model EH66 series only).
14 Pelco Manual C411M-D (1/96) 9.1 RECOMMENDED CABLE SIZE CAUTION : When a single po wer source is used for both the camera and accessories, the camera power consumption must be taken into consideration when determining the wire gauge.
Pelco Manual C411M-D (1/96) 15 10.0 WARRANTY AND RETURN INFORMATION PRODUCT WARRANTY AND RETURN INFORMA TION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment.
16 Pelco Manual C411M-D (1/96) Pelco 3500 Pelco Way, Clovis, CA 93612-5699 • (559) 292-1981 • (800) 289-9100 FAX (559) 292-3827 • (800) 289-9150 • www.pelco.com International customers call 1-559-292-1981 or FAX 1-559-348-1120 (Product specifications subject to change without notice.
An important point after buying a device Pelco EH66X (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Pelco EH66X yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Pelco EH66X - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Pelco EH66X you will learn all the available features of the product, as well as information on its operation. The information that you get Pelco EH66X will certainly help you make a decision on the purchase.
If you already are a holder of Pelco EH66X, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Pelco EH66X.
However, one of the most important roles played by the user manual is to help in solving problems with Pelco EH66X. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Pelco EH66X along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
