Instruction/ maintenance manual of the product EH4718L/PSA Pelco
Go to page of 12
EH4718L/WPSA and EH4718L/PSA Envir onmental Enclosur es Installation/ Operation Manual C1415M-PSA (12/97) Pelco • 3500 W. Pelco Way, Clovis • CA 93612-5699 USA • www.
12 Pelco Manual C1415M-PSA (12/97) ii CONTENTS Section Page 1.0 GENERAL .................................................................................................. 1 1.1 IMPORT ANT SAFEGUARDS AND WARNINGS ............................... 1 2.0 DESCRIPTION .
Pelco Manual C1415M-PSA (12/97) 1 Please thoroughly familiarize yourself with the information in this manual prior to installation and operation. 1.0 GENERAL 1.1 IMPORT ANT SAFEGUARDS AND W ARNINGS Prior to installation and use of this product, the following W ARNINGS should be observed.
2 Pelco Manual C1415M-PSA (12/97) 2.0 DESCRIPTION The EH4718L/WPSA and EH4718L/PSA environmental enclosures are constructed of aluminum. They are installed by attaching the bottom of the enclosure to the tilt shaft of an PT780-24P/PPPSA pan/tilt. 2.1 MODELS EH4718L/WPSA Environmental enclosure with rear opening lid.
Pelco Manual C1415M-PSA (12/97) 3 3.0 INST ALLA TION 1. Unlatch and raise the enclosure lid. The gas spring will hold the lid in place when it is fully opened. 2. Remove the parts tied to the camera sled 3. Remove the elevator from the camera sled. 4.
4 Pelco Manual C1415M-PSA (12/97) Figure 1. Support Bracket Installation.
Pelco Manual C1415M-PSA (12/97) 5 4.0 WINDOW WIPER ADJUSTMENTS 1. Open the enclosure lid. 2. Refer to Figure 2 and set either of the following two options: a. The time between wiper strokes can be adjusted between 3 and 10 sec- onds by rotating the potentiometer R8.
6 Pelco Manual C1415M-PSA (12/97) 5.0 OPERA TION The fan turns on at 1 10 ° F (43 ° C) and turns off at 88 ° F (31 ° C)..
Pelco Manual C1415M-PSA (12/97) 7 6.0 MAINTENANCE Clean the window with a mild nonabrasive detergent in water and a soft cloth to maintain picture clarity .
8 Pelco Manual C1415M-PSA (12/97) 7.0 WIRING DIAGRAM Figure 3. EH4718L/WPSA and EH4718L/PSA Wiring Diagram.
Pelco Manual C1415M-PSA (12/97) 9 8.0 SPECIFICA TIONS ELECTRICAL Input Voltage: 24, 120 or 230 VAC, 50/60 Hz Electrical Connections: 9-pin round lens control connector Two wires for camera power BNC f.
10 Pelco Manual C1415M-PSA (12/97) 9.0 WARRANTY AND RETURN INFORMA TION Pelco, the Pelco logo, Camclosure, Esprit, Genex, Legacy, and Spectra are registered trademarks of Pelco. Endura and ExSite are trademarks of Pelco. © Copyright 1997, Pelco. All rights reserved.
An important point after buying a device Pelco EH4718L/PSA (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Pelco EH4718L/PSA yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Pelco EH4718L/PSA - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Pelco EH4718L/PSA you will learn all the available features of the product, as well as information on its operation. The information that you get Pelco EH4718L/PSA will certainly help you make a decision on the purchase.
If you already are a holder of Pelco EH4718L/PSA, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Pelco EH4718L/PSA.
However, one of the most important roles played by the user manual is to help in solving problems with Pelco EH4718L/PSA. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Pelco EH4718L/PSA along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
