Instruction/ maintenance manual of the product DX7016-180 Pelco
Go to page of 52
DX7000 Series Digital V ideo Recor der Installation/ Operation Manual C682M-E (11/01) ® Pelco • 3500 Pelco W ay • Clovis, CA 93612-5699 USA • www .
2 Pelco Manual C682M-E (1 1/01) CONTENTS IMPORT ANT SAFEGUARDS AND W ARNINGS ...................................................... 5 DESCRIPTION .........................................................................................................
Pelco Manual C682M-E (1 1/01) 3 LIST OF T ABLES AV ideo Coaxial Cable Requirements ................................................................... 7 INST ALLING THE DX7000CD (CD-RW Drive) ...................................................... 38 LOADING THE DIRECTCD SOFTW ARE .
4 Pelco Manual C682M-E (1 1/01) (This page intentionally left blank.).
Pelco Manual C682M-E (1 1/01) 5 IMPOR T ANT SAFEGUARDS AND W ARNINGS Prior to installation and use of this product, the following W ARNINGS should be observed. 1. Installation and servicing should only be done by qualified service personnel and con- form to all local codes.
6 Pelco Manual C682M-E (1 1/01) DESCRIPTION The DX7000 Series are high-quality digital video recorders (DVR) that combine the functions of a recorder and multiplexer into a product with versatile recording and playback functions. The units are capable of dual operation and can record and play back video at the same time.
Pelco Manual C682M-E (1 1/01) 7 INST ALLA TION Place the DVR on any flat surface (desk or table) or install in any standard 19-inch (48.26 cm) wide console or rack configuration. Figure 1. Rear View of Back Panel 1 Camera Inputs – Refer to T able A for video coaxial cable distances.
8 Pelco Manual C682M-E (1 1/01) TWO-WIRE CONTROL SYSTEM INST ALLA TION 1. Connect the control wires from the receiver to the RS-422 converter . The DX7000 can support up to 16 PTZ devices. T o connect more than one PTZ to the system, refer to Figure 3.
Pelco Manual C682M-E (1 1/01) 9 PROGRAMMING T urn the system power ON; the Main Screen (DISPLA Y mode) appears. Figure 5. Display Mode DISPLA Y MODE 1 Date and Time Indicator – Displays current date and time. 2 SEARCH Button – Plays back and search recordings by date and time.
10 Pelco Manual C682M-E (1 1/01) DX7000 SYSTEM SETUP To setup the DX7000 Digital Video Recorder use the left mouse button and click on the SETUP button located in the DISPLA Y mode. CAMERA SETUP Figure 6. Channel Setup Menu 1 CAMERA NAME Box 2 SIGNAL TYPE – Selection must correspond with the NTSC/P AL selection switch setting.
Pelco Manual C682M-E (1 1/01) 11 COLOR SETUP Figure 7. Color Setup Menu 1 CON – Adjusts the CONTRAST of the viewed and recorded scene. 2 BRI – Adjusts the BRIGHTNESS of the viewed and recorded scene. 3 RED – Adjusts the RED level of the viewed and recorded scene.
12 Pelco Manual C682M-E (1 1/01) SCHEDULE SETUP Figure 8. Schedule Setup Menu 1 GROUP (01-24) – Selects group to be scheduled. 2 Sets ST ART TIME and END TIME for recording group. 3 Schedule Selection Buttons CLEAR ALL SCHEDULE – Clears all GROUP (1-24) schedules.
Pelco Manual C682M-E (1 1/01) 13 Evaluate the flow of motion at the surveillance site before programming a schedule. A record- ing schedule can consist of one of the following modes and/or a combination of all modes: NORMAL – Continuous recording recommended for surveillance areas with a lot of movement.
14 Pelco Manual C682M-E (1 1/01) SPEED SETUP Figure 9. Speed Setup Menu 1 RECORDING SPEED MODE a. NORMAL – Sets recording speed for continuous recording. b. MOTION – Sets motion detection and pre-alarm recording speeds. c. SENSOR – Sets sensor detection and pre-alarm recording speeds.
Pelco Manual C682M-E (1 1/01) 15 MOTION DETECTION SETUP Figure 10. Motion Detection Setup Menu 1 BEEP – Beeps when motion is detected. 2 SENSITIVITY – Adjusts the sensitivity of the detection areas. 3 CLEAR ALL BLOCK – Deletes all motion detection area blocks.
16 Pelco Manual C682M-E (1 1/01) P ASSWORD SETUP Figure 1 1. Password Setup Menu 1 SELECT LEVEL – Levels include Administrator , Search User , PTZ/Backup User , and Client User . 2 INPUT AREA – Password input window . 3 NUMBER BUTTONS – Use number buttons to input password.
Pelco Manual C682M-E (1 1/01) 17 P AN & TIL T SETUP Figure 12. Pan and T ilt Protocol Menu 1 Select pan and tilt protocol by scrolling through the selections in the RX TYPE box. QUIT TO EXPLORER The DX7000 uses a Window’s based operating system.
18 Pelco Manual C682M-E (1 1/01) OPERA TION RECORDING ST A TUS The colored circle located to the right of the on-screen camera title indicates the recording status of the camera. RED indicates that the camera is recording continuously . If the circle is BLUE, camera recording was triggered by motion detection.
Pelco Manual C682M-E (1 1/01) 19 PA TTERN A pattern is a user-defined, viewable camera path with a definite beginning and end. The pattern can consist of any standard pan and tilt or lens commands. Once defined the pattern is easily activated with the press of an on-screen menu button.
20 Pelco Manual C682M-E (1 1/01) PRESET TOURS A preset tour is a programmed sequential execution of preset positions. How to Program a Pr eset T our 1. Click the PTZ button in the DISPLA Y Mode. The PTZ Mode appears. 2. Click the left mouse button on PRESET .
Pelco Manual C682M-E (1 1/01) 21 SEARCH CONTROL MODE Figure 15. Search Control Menu 1 Date and Time Indicator – Displays current date and time. 2 Search Date – Displays year , month, and time of search. 3 Search Window – Flashes when system is searching through cameras.
22 Pelco Manual C682M-E (1 1/01) SELECT DA TE AND TIME 1. Enter the year and month in the SEARCH DA TE area of the menu. Click the up or down arrow buttons to make a selection. 2. Enter the hour and minute in the SEARCH DA TE area of the menu. Click the arrow buttons up or down to make a selection.
Pelco Manual C682M-E (1 1/01) 23 BACKUP TO 3.5-INCH DISKETTE 1. Press the CAMERA SELECTION button. 2. Disable all cameras in search mode. FDD backup cannot be done when the viewing screen is divided. 3 Select one camera. 4. Click the FDD button. The BACKUP window appears.
24 Pelco Manual C682M-E (1 1/01) REMOTE SITE SOFTW ARE DESCRIPTION Free remote site software is included with the DX7000 to provide remote site viewing of live and recorded video. The software is compatible with Windows 98 and Windows 2000. INST ALLA TION To install the remote users software: 1.
Pelco Manual C682M-E (1 1/01) 25 REGISTERED SITE SETUP Figure 18. Setup Screen 1 Date and Time Indicator – Displays current date and time. 2 SITE NAME – Enters the name of the site. 3 ADDRESS – Inputs the IP address or phone number of site. 4 P ASSWORD – Use only if the DX7000 registered site is CLIENT USER password protected.
26 Pelco Manual C682M-E (1 1/01) OPERA TION Figure 19. Online Mode 1 Date and Time Indicator – Displays current date and time. 2 SEARCH Button – Plays back and searches recordings by date and time. 3 PTZ Control Button – Controls pan, tilt, and zoom functions.
Pelco Manual C682M-E (1 1/01) 27 9 Screen Division – Single camera display Displays cameras 1-9 Quad display , cameras 1-4 Displays cameras 10-16 Quad display , cameras 5-8 Displays all 16 cameras Quad display , cameras 9-12 Sequencing mode – Sequence using single, four , or nine camera displays.
28 Pelco Manual C682M-E (1 1/01) VIEW It is not necessary to use the screen division buttons located in the lower left corner of the screen to change the camera view . Y ou can use the left and right mouse buttons to in- stantly view a single camera or remove the menu bars from the display .
Pelco Manual C682M-E (1 1/01) 29 PA TTERN A pattern is a user-defined, viewable camera path with a definite beginning and end. The pattern can consist of any standard pan and tilt or lens commands. Once defined the pattern is easily activated with the press of an on-screen menu button.
30 Pelco Manual C682M-E (1 1/01) Figure 21. Pattern and Preset Bars PRESET TOURS A preset tour is a programmed sequential execution of preset positions. How to Run A Preset T our 1. Click the PTZ button in the DISPLA Y Mode. The PTZ Mode appears. 2. Click the left mouse button on PRESET .
Pelco Manual C682M-E (1 1/01) 31 SEARCH MODE Figure 22. Search Mode 1 Date and Time Indicator – Displays current date and time. 2 Search Date – Selects month and year to search video. 3 Search Time – Selects the time (hour and minute) to search video.
32 Pelco Manual C682M-E (1 1/01) SELECT DA TE AND TIME 1. Enter the year and month in the SEARCH DA TE area of the menu. Click the up or down arrow buttons to make a selection. 2. Enter the hour and minute in the SEARCH DA TE area of the menu. Click the arrow buttons up or down to make a selection.
Pelco Manual C682M-E (1 1/01) 33 EMERGENCY AGENT SOFTW ARE Figure 24. Emergency Agent Window Emergency Agent software alerts the remote site client of any triggered alarm at the surveil- lance site. When an alarm is triggered a popup widow appears on the monitor of the remote site client.
34 Pelco Manual C682M-E (1 1/01) BACKUP VIEWER SOFTW ARE Use the Backup Viewer software to search images stored on backup media, DA T tape or DVD disc. To install the Backup Viewer: 1. Start Windows 98. 2. Close all programs, including any anti-virus programs.
Pelco Manual C682M-E (1 1/01) 35 BACKUP VIEWER OPERA TION Figure 25. Backup Viewer 1 Date and Time Indicator – Displays current date and time. 2 Search Date – Displays year , month, and time of search. 3 Search Window – Flashes when system is searching through cameras.
36 Pelco Manual C682M-E (1 1/01) WA TERMARK TOOL The W atermark tool allows you to verify if an original image has been altered. The W atermarking V iewer software is available on the Remote Site Software CD. T o install the Watermark V iewer: 1. Start Windows 98.
Pelco Manual C682M-E (1 1/01) 37 Figure 27. The Image Has Been Altered There are three indications that an image has been altered: 1. A red frame around the image. 2. The image is shaded. 3. The message “Image has been altered or has not been watermarked” appears in the lower left-hand corner of the screen.
38 Pelco Manual C682M-E (1 1/01) INST ALLING THE DX7000CD (CD-RW DRIVE) 1. Connect one end of the USB data cable to the CD-RW drive. Connect the other end of the USB data cable to the USB serial port (1 or 2) located on the back panel of the DX7000 DVR.
Pelco Manual C682M-E (1 1/01) 39 6. Click Next. The following message appears: 7. Select Search for the Best Driver for Y our Device. Click Next and the following window appears: 01 182 01 183.
40 Pelco Manual C682M-E (1 1/01) 8. Select Floppy Disk Drives and click Next. The following appears: 9. Accept the recommended driver by clicking Next. The following window appears: 10. Click Finish. 11 . After installing the driver remove the floppy disk from the A:/ drive.
Pelco Manual C682M-E (1 1/01) 41 LOADING THE DirectCD SOFTW ARE 1. From the DISPLA Y mode of the DX7000 click on the SETUP button. The SETUP mode appears. 2. Click the EXIT TO EXPLORER button. Windows Explorer appears. 3. Insert the hp cd-writer installation software – disc 1 into the CD-R W drive.
42 Pelco Manual C682M-E (1 1/01) PREP ARING CD-R W MEDIA FOR BACKUP NOTE: The initial format of a CD-RW disk can take a considerable amount of time, approximately three hours. T o speed up the procedure of copying files to a backup device, always have a formatted CD-RW disc readily available.
Pelco Manual C682M-E (1 1/01) 43 8. Select the CD-RW drive and click Next. The following appears: 9. T ype the title of the CD-RW in the place provided, and then select Finish. The follow- ing dialog box appears. 10. Select OK; fast format is initiated.
44 Pelco Manual C682M-E (1 1/01) BACKUP WINDOW Figure 29. Backup (COPY) Window 1 SELECT DRIVE box – Lists drives with files available for backup. 2 STORED ITEMS box – Lists all files stored in the selected drive. 3 ADD button – Adds stored files to ITEMS TO BACKUP box.
Pelco Manual C682M-E (1 1/01) 45 HOW TO BACKUP (COPY) TO THE CD-RW DRIVE 1. From the DISPLA Y mode of the DX7000, click the COPY button. The SETUP mode appears. NOTE: If the COPY button is not available it has not been initiated. Refer to the Initiate DX7000 Copy Button section of this manual.
46 Pelco Manual C682M-E (1 1/01) DX7000EM (External Modem) CONNECT THE EXTERNAL MODEM TO THE DX7000 1. Connect the 25-pin end of the RS-232 cable (supplied with the modem) to the serial port located on the back panel of the modem. 2. Connect other end of the RS-232 cable to the COM 2 serial port located on the back panel of the DX7000.
Pelco Manual C682M-E (1 1/01) 47 LOAD THE DRIVER FOR THE MODEM 1. From the DISPLA Y mode of the DX7000, click the EXIT button. A dialog box appears. Select Y es. The DX7000 shuts off. 2. T urn ON the modem and restart the DX7000 system by pushing the ON/OFF switch located on the front panel.
48 Pelco Manual C682M-E (1 1/01) 5. Select Search for the Best Driver for Y our Device. Click Next, the following appears: 6. T ype C:WindowsSystem in the space provided. Click Next, the following appears: 7. Accept the recommended driver by clicking Next.
Pelco Manual C682M-E (1 1/01) 49 8. Click Finish, the DX7000’s DISPLA Y mode appears. 9. From the DISPLA Y mode of the DX7000 click the SETUP button. The SETUP mode appears. 10. Click the SPEED button. The SPEED SETUP window appears. a. Check the Use Modem box.
50 Pelco Manual C682M-E (1 1/01) SPECIFICA TIONS ELECTRICAL/VIDEO Input V oltage: 100-240 V AC switchable, 50/60 Hz Signal System: NTSC/P AL CPU & RAM DX7008: Celeron, 128 MB DX7016: Pentium ® II.
Pelco Manual C682M-E (1 1/01) 51 NOTES.
® Pelco, the Pelco logo, Spectra, Genex, and Legacy are registered trademarks of Pelco. © Copyright 2001, Pelco ™ Esprit and Camclosure are trademarks of Pelco. All rights reserved. ® Windows is a registered trademark of Microsoft. ® Pentium is a registered trademark of Intel.
An important point after buying a device Pelco DX7016-180 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Pelco DX7016-180 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Pelco DX7016-180 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Pelco DX7016-180 you will learn all the available features of the product, as well as information on its operation. The information that you get Pelco DX7016-180 will certainly help you make a decision on the purchase.
If you already are a holder of Pelco DX7016-180, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Pelco DX7016-180.
However, one of the most important roles played by the user manual is to help in solving problems with Pelco DX7016-180. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Pelco DX7016-180 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
