Instruction/ maintenance manual of the product CM9700MDD-EVS Pelco
Go to page of 54
CM9700MDD-EVS Matrix Digital Decoder INSTALLATION/OPERATION C1570M-C (5/06).
.
C1570M-C (5/06) 3 Contents Regulatory Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Description .
4 C1570M-C (5/06) List of Illustrations 1 CM9700MDD-EVS Front View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 2 CM9700MDD-EVS Rear View .
C1570M-C (5/06) 5 List of T ables A RS-422 Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 B Video Coaxial Cable Requirements .
6 C1570M-C (5/06) Regulatory Notices REGULA TORY NOTICES This device co mplies with Pa rt 15 of the FCC Rules. Operat ion is subject to the following two conditions: (1) this device may n ot c ause harmful interference, and (2 ) this device must accept any interference received , including interference t hat may cause undesired op erat io n.
C1570M-C (5/06) 7 Description The CM970 0MDD-EVS matrix di gital decode r uses th e latest En dura ™ technology to transmit video from E ndura products to CM97 00 Series matrix switcher s (using 9.
8 C1570M-C (5/06) FRONT VIEW Figure 1 illustrates the co mponents on the front of the CM9700MDD-EVS. Refer to Front Panel Indicato rs in the Operation s ection for a d escription o f each indic ator . Figure 1. CM9700MDD-EVS Front V iew REAR V IEW Figure 2 illustrates the co mponents on the rear of the CM9700MDD-EVS.
C1570M-C (5/06) 9 SAMPLE APPLICATION IMPORTANT NOTE. PLEASE READ The network implem entation is shown as a ge neral repres entation onl y and is no t intended to show a deta iled network topology. Y our actual network will differ , requ iring changes or per haps additional netw ork equipment to accommoda te the syst em as illustra ted.
10 C1570M-C (5/06) Installation HARDWARE INSTALLATION OVERVIEW The following steps provide an overview of how to ins tall the CM9700 MDD-EVS: 1. Install all components of the matrix switching system. Refer to the ma trix system documentat ion for instruc tions.
C1570M-C (5/06) 11 PRODUCT SERIAL NUMB ER LABEL PLACEMENT Product serial number labe ls help Pelco’ s Product Support id entify your system and its factory configuration in the event that the CM9700MDD-EVS or its componen ts require ser vice. A label citing your product’ s serial number is attached to the bottom pan el of the CM9700MDD-EVS.
12 C1570M-C (5/06) MOUNTING Use one of the following in stallation meth ods for the CM 9700MDD-EVS: • Place the CM9700M DD-EVS on a flat surface, such as a shelf or desktop • Mount the CM9700MD D-EVS to a wall using the option al WM5001-4U wall mount kit • Install the CM9700MDD-EVS in the optional RK5 000PS-5U rack mo unt kit.
C1570M-C (5/06) 13 WALL MOUNT INSTALLATION The CM9700MDD-E VS can be mounted to a wall u sing the optional WM50 01-4U wall mount system. Y ou can mount up to four CM9700MDD-EVS un its, in any co mbination, in a fully expa nded WM5001-4U (one WM5001-4U wit h up to thre e WM5001-4UE XP expansion units).
14 C1570M-C (5/06) RACK MOUNT INSTALLATION Up to 12 CM97 00MDD-EVS unit s can be moun ted in the o ptional RK500 0PS-5U rack mount kit. Ea ch unit plugs di rectly into a power c onnector in the rack and is powere d by the rack. NOTE: The RK5000PS-5U only supplies power .
C1570M-C (5/06) 15 PELCO BADGE ORIENTATION The Pelco ba dge on the f ront panel of the CM9700MDD -EVS can be ro tated in quar ter turns. If you install the unit on a flat sur f ace, the Pelco badge will be turn ed the wrong way . T o rotate the Pelco badge: 1.
16 C1570M-C (5/06) BASIC HARDWARE CONNECTIONS CM9700-CC1 CONNECTION Use the 16-pin te rminal block for the RS- 422 serial connection (Pelco P protocol) between the CM9700MDD-EVS an d the CM9700-CC1 . The termina l block has t ension clamps instead of screw terminal s.
C1570M-C (5/06) 17 NOTE: Remember that the first fe w RS-422 COM ports on the CC1 must be use d for one or more matrix bays and any n etwork interface unit s and hot swit ch units.
18 C1570M-C (5/06) Figure 13. Sample Video Connection Between the CM9700MDD-EVS and the CM9760-MXB NOTE: Figure 13 illustrates a samp le video connection.
C1570M-C (5/06) 19 Figure 14. Sample Video Connection Between the CM 9700M DD-EVS and the CM9770-MXB NOTE: Figure 14 illustrates a samp le video connection.
20 C1570M-C (5/06) Figure 15. Sample Video Connection Between the CM9700MDD-EVS and the CM9780-MXB NOTE: Figure 15 illustrates a samp le video connection.
C1570M-C (5/06) 21 AUDIO OUTPUT CONNECTION The CM9700MDD -EVS supports one audio output, which allows you to contro l a speaker or oth er audio equipmen t at the monitored lo cation. NOTE: When using mul tiple CM9700MDD -EVS units, an additional audio routing solution may be required.
22 C1570M-C (5/06) NETWORK CONNECTION NOTE: Consult your network admi nistrator before installing the CM9700MDD-EVS to avoid possible network conflicts. Use the netw ork port on t he front pan el and a 10 0BaseT netw ork Ca t5e (or better) cable with RJ-45 conn ectors to connect the CM9 700MDD-E VS to your system networ k.
C1570M-C (5/06) 23 POWER CONNECTION The CM9700MDD -EVS offers a single four -pin power connecto r . The RK5000PS-5 U rack mount kit and the NET5 301PS attach to the fo ur -pin connector . When using a d ifferent power supply, attach power to th e enclosed four-pin to two-pin adapt er and att ach the ad apter to t he uni t.
24 C1570M-C (5/06) Connect power to the CM9700MDD-EVS. The Pelco badge (blue) an d the status light (gre en) on the fron t panel should glow . Figure 18.
C1570M-C (5/06) 25 Software Configuration Once the hardwar e installation and all device connect ions are comp leted, you will need to complete the follo wing software confi guration tasks: • Use the CM9700 -MGR software to a dd the CM9700 MDD-EVS and Endu ra cameras to t he matrix syste m configuratio n.
26 C1570M-C (5/06) ADD THE CM9700MDD-EVS AND ENDURA CA MERAS TO THE 9700 MATRIX CONFIGURATION T o add a CM9700MDD-EVS to a 9700 matrix system configuration, you ne ed to complete the following tasks: 1. Add the CM9700M DD-EVS to the matrix system configuratio n.
C1570M-C (5/06) 27 Figure 21. Number of Devices Page Select the numb er of CM9700MD D-EVS units. Remembe r that one mat rix bay input must be availa ble for eac h CM9700MDD-EVS, s o the number of un its cannot exce ed the num ber of ava ilable inputs o n the matr ix bay .
28 C1570M-C (5/06) CONFIGURE THE CM9700MDD-EVS SETTINGS When you click a CM9700M DD-EVS unit in the tree view port ion of the CM9700-MGR main window , the CM9700MDD-EVS unit’ s properties open in the proper ties box. Use these pr operty fields to configure each CM9700MDD-E VS unit.
C1570M-C (5/06) 29 ADD ENDURA CAMERAS TO THE MATR IX SY STEM CONFIGURATION 1. Click Wizards > Add Device Wiza rd. The Add Device wizard op ens. 2. Specify Camera in the Select Device T yp e drop-down box, and th en click EnduraCam in the Sele ct Model drop-down box.
30 C1570M-C (5/06) Figure 27. Device Identification Page 6. Specify the device name(s) an d logical number range by complet ing the following fields: Name: T ype a base name for the device. If you wan t a space between th e name and the logic al number , use the spa cebar to ente r a space after the name.
C1570M-C (5/06) 31 CONFIGURE A CM9700 SOFT ALARM TO REPRESENT AN ENDURA ALARM 1. Use the Endur a WS5000 app lication to conf igure alarms in t he Endura system. Be sure to assign e ach alarm a uniqu e logical num ber . These can be contact alarms or motion alarms.
32 C1570M-C (5/06) MACRO CONFIGURATION T o configure a CM 9700 macro to activate a s cript in the E ndura system, co mplete the fol lowing steps: 1. In the Endura system co nfigure a script to complete the desired task.
C1570M-C (5/06) 33 Figure 32. Macro Editor Windo w 3. In the macro comma nd tree, click Mi scellaneous, and then double cl ick the RES (Run Endura Script) command. The command is add ed as a step in the macro step gr id. Figure 33. Add a Run Endura Script Command 4.
34 C1570M-C (5/06) NETWORK VIDEO RECORDER MANAGEMENT Y ou can u se the matri x system and t he CM9700MDD-E VS as an NVR (networ k video re corder) manage ment tool.
C1570M-C (5/06) 35 5. Click Finis h on the Add More Devices p age. The spe cified numb er of NVR units is added to the matrix sy stem configu ration. 6. T o view an NVR, click the + symbol next to any CM9700MDD-EVS, and then click the + symb ol next to the IP Network.
36 C1570M-C (5/06) CONFIGURE A CM9700 MACRO TO SW ITCH VIDEO TO A BACKUP NVR 1. Use the CM9700 -MGR software to a dd a macro, and t hen click Edit Steps to open th e Macro Editor window . Refer to the Ma cros section in the CM9700-MG R Software Guide for de tailed instru ctions.
C1570M-C (5/06) 37 ASSOCIATE A MACRO WITH A SOFT ALARM 1. Use the CM9700- MGR Add Soft Alarms Wiza rd to add a soft alarm for ea ch NVR. 2. (Optional) Give each alarm a recogniza ble name. 3. Click a soft alarm, and then select a macro in the Ma cro drop-down bo x.
38 C1570M-C (5/06) EXPORT THE CONFIGURATION FILES AND T R ANSFER THE DATA TO THE CM9700MDD-EVS Once you have configured the CM 9700MDD-EVS settings in the CM9700-MGR software, complete the following tasks to transfer the da ta to the matrix system c omponents: • Export the configura tion files, and then transf er these files to th e CM9700-CC1.
C1570M-C (5/06) 39 3. Use the Endu ra WS5000 applica tion to transfer the XML file to the CM9700MDD-EVS t hrough th e Endura net work, as des cribed in t he following steps: a. Click the Devices tab in the WS5000 Setu p Window . b. Navigat e to the CM97 00MDD-EVS unit.
40 C1570M-C (5/06) Operation FRONT PANEL INDICATORS Figure 45. CM9700MDD-EVS Front Panel Pelco badge (power indica tor) The Pelco ba dge glows blu e when the unit has power . Unit status indicator Unit status is indicated by one of the following th ree colors: Green The unit is functio ning normally.
C1570M-C (5/06) 41 VI E W I N G VI D E O If you have not already do ne so, install the CM9760-KBD keyboard, connect it to the matrix system, and then complete the basic setup process. Refer to the CM9760-KBD/CM9760-KBR Installation/Operation ma nual for instructions; this manual is provided in the matrix system binder .
42 C1570M-C (5/06) 5. T o switch the video mode (from live to recorded , or vice versa), press the MORE ico n to view DVR Menu 2, an d then press the S witch Mode icon. Figure 47. DVR Menu 2 6. T o access the r emaining DVR icons, which appear on DVR Menu 3, press the MORE icon.
C1570M-C (5/06) 43 V IEWING AND CONTROLLING VIDEO NOTE: In the fol lowing proced ures the “Sel ect Play” or “Select Pause ” step can b e accomplished either by mo ving the joys tick or by pr essing the keyboard icon.
44 C1570M-C (5/06) Seek (Search for a Specific T ime) Live Video 1. While viewi ng live video, press the Se ek icon. The keyboard LCD disp lays the dat e field. 2. Enter the date (MMDDYYYY), and then press the Seek icon again. The keyboard LCD displays the time field.
C1570M-C (5/06) 45 Using Digital Zoom (Recorded V ideo Only) During pl ayback of re corded vi deo, you can use the di gital zoom f eature to enlarge a portion of the video image. When th e digit al zoom feature is enabled, you wil l see a picture-in- picture fra me on the monitor .
46 C1570M-C (5/06) Controlling Recorded Vi deo wit h the Joy stick Many of the jo ystick moveme nts described below oper ate in both mo mentary and lat ching modes. These modes a re defined as follows : • Momentary mode: The operatio n is activa ted until yo u release the joystick.
C1570M-C (5/06) 47 Current Mode = Play: • T o the right a little: vid eo plays at 2 x (momentary). • T o the right a little more : video plays at 4x (momen tary). • T o the right al l the way: vi deo plays at 2x (latching ). • T o the right all the way a gain: video plays at 4x (latching).
48 C1570M-C (5/06) CONFIGURING THE OFFSET+ AND OFFSET - FUNCTIONS TO SWITCH CAMERAS The Offset+ an d Offset - functions allow you t o configur e an offse t value, wh ich a llows an easy way to switch cameras. T o configure th e Offset+ and Offset - functions, complete the fo llowing steps: 1.
C1570M-C (5/06) 49 Figure 52. Assigning an Alternate Camera 3. Specify the Endura logi cal camera number as the altern ate ca mera. For the examp le described ab ove, you would specif y logical camera number 5001. 4. Click OK to close the Alternate Cameras dia log box, and then save the configuration changes.
50 C1570M-C (5/06) T roubleshooting If the following in structions fa il to solve your problem, contact Pelco P roduct Support at 1-800-289-91 00 or 1-559- 292-1981 for ass istance. Access the pro perties window f or the CM9700MDD- EVS unit on th e WS5050 Endura work station (ref er to the WS5000 operation manua l) .
C1570M-C (5/06) 51 Specifications MODEL CM9700MDD-EV S Matrix digital de coder (NET5301R optimized fo r us e with matrix) that converts digital video streams from Endura prod ucts into ana log video to be viewed an d controlled on a Pelco CM9700 Series matrix switch er .
52 C1570M-C (5/06) POWER Power Consumptio n 12 watts, 41BTU/H Power Input 12 VDC +10%/-1 5% 24 VAC +10%/-15% Power Connecto rs 4-pin For RK50 00PS-5U or NET5301P S 4-pin to 2- pin adap ter Fo r user-s.
PRODUCT WARRANTY AND RETURN INFORMA TION WARRANTY Pelco will repair or replace, witho ut charge, an y merchandise p roved defecti ve in material or workmanship for a period of one year after the date of sh ipment.
United States | Canada | United Kingdom | The Netherlands | Singapore | Spain | Scandinavia | France | Middle East W orldwide Headquarters 3500 Pelco W ay Clovis, California 93612 USA USA & Canada T el: 800/289-9100 Fax: 800/289-9150 International T el: 1-55 9/292-1981 Fax: 1-559/348-1120 www .
An important point after buying a device Pelco CM9700MDD-EVS (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Pelco CM9700MDD-EVS yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Pelco CM9700MDD-EVS - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Pelco CM9700MDD-EVS you will learn all the available features of the product, as well as information on its operation. The information that you get Pelco CM9700MDD-EVS will certainly help you make a decision on the purchase.
If you already are a holder of Pelco CM9700MDD-EVS, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Pelco CM9700MDD-EVS.
However, one of the most important roles played by the user manual is to help in solving problems with Pelco CM9700MDD-EVS. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Pelco CM9700MDD-EVS along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
