Instruction/ maintenance manual of the product CCC5100H Pelco
Go to page of 16
QUICK START GUIDE C2910M-B- Q S (2/06) CCC5100H Series Camera.
2 C2910M-B-QS (2/06) This quick start guide describes how to install and confi gure the CCC5100H Series camera in most applications. It contains a representation of the setup menus to help you locate and change specific settings.
C2910M-B-QS (2/06) 3 H AR DW AR E Refer to Figure 1 as you install the CCC5100H Series camera. Figure 1. CCC5100H Connectors VIDEO CONNECTOR SERVICE CONNECTOR SETUP BUTTONS MULTIFUNCTION (RJ45-10) CON.
4 C2910M-B-QS (2/06) LENS The CCC5100H Series camera supports both manual and DC-drive auto iris lenses, either fixed focal length or varifocal. The camera accepts both CS- and C-mount lenses without an adapter . T o mount the lens onto the camera: 1.
C2910M-B-QS (2/06) 5 CONNECTIONS The CCC5100H Series camera offers standard power and coax video connectors. T o use the RJ45-10 multifunction connector that combines power, video, and control leads, refer to Multifunction Connector in the Installation/Operation manual.
6 C2910M-B-QS (2/06) SETUP MENUS Use the setup menus to customize the camera settings. Refer to the setup menus as shown on this and the opposite page: CAMERA DISPLAY CAMERA NAME CCC5100H RX ADDRESS 1.
C2910M-B-QS (2/06) 7 WHITE BALANCE MODE ATW NORMAL <ATW NORMAL /DESAT> <MANUAL RED/BLUE> <MANUAL COLOR TEMP> BACK EXIT ATW NORMAL /DESAT LOW LIMIT HIGH LIMIT BACK EXIT |------+------| |------+------| 2k 5.5k 5.5k 11k PROFILES ACTIVE WDR SAVE AS CUSTOM1 DEFAULT WDR BACK EXIT SYSTEM INFORMATION FIRMWARE VER.
8 C2910M-B-QS (2/06) A CCESSING THE SETUP MENUS Use the top, center , and bottom buttons on the rear panel to access and navigate the setup menus. T able A lists the button presses for each menu action. A short press is less than one second; a long press is more than one second.
C2910M-B-QS (2/06) 9 C A ME RA P R OFILE Select a basic camera profile and then customize it. After you save your custom camera settings into a user-definable profile, change the default to CUSTOM1 or CUSTOM2. C A UTION: Be sure to save all camera settings into a user-definable profile so they will not be lost in case the camera loses power .
10 C2910M-B-QS (2/06) 4. Select the user-definable profile to use during power -up: a. Select DEFAUL T and press the center button. b. Press the top or bottom button to select your profi le: CUSTOM1 or CUSTOM2. c. Press the center button to set the new default profi le.
C2910M-B-QS (2/06) 11 DC-D R IVE A UTO I R IS LENS SETUP Before using a DC-drive auto iris lens, you must adjust the DC offset setting. Use the following steps to match the camera’ s DC voltage setting to the drive circuit on the auto iris lens: 1. Remove the lens from the camera.
12 C2910M-B-QS (2/06) 9. Hold the auto iris lens so you can watch the iris (refer to Figure 3). Then increase the DC OFFSET setting slowly until the iris closes. Figure 3. Open Iris and Closed Iris 10. As soon as the iris closes, slowly decrease the DC OFFSET value by 14, or until the iris opens again.
C2910M-B-QS (2/06) 13 LENS FOCUS Focus the camera lens. 1. A uto iris only: Cover the auto iris lens with a suitable neutral density (ND) filter to open the iris fully . For best results, use an ND3 filter . 2. Manual iris only: Open the iris completely .
14 C2910M-B-QS (2/06) 6. Fixed focal length lens only: a. Set the lens focal length to far ( ∞ ). b. Adjust the back focus. Move the back focus locking screw on the camera up or down until the image is focused. As the focus improves, the value on the FINE FOCUS menu increases: the higher the number, the better the focus.
C2910M-B-QS (2/06) 15 R evision History Manual No. Date Comments C2910M-QS 9/04 Original version. C2910M-A-QS 4/05 Updated for RGB filters, new firmware. C2910M-B-QS 2/06 Removed the high voltage and RGB models. Updated the OSD version. Changed the active profile default.
Worldwide Headquarters 3500 Pelco Way Clovis, California 93612 USA USA & Canada T el: 800/289-9100 Fax: 800/289-9150 International T el: 1-559/292-1981 Fax: 1-559/348-1120 www .
An important point after buying a device Pelco CCC5100H (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Pelco CCC5100H yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Pelco CCC5100H - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Pelco CCC5100H you will learn all the available features of the product, as well as information on its operation. The information that you get Pelco CCC5100H will certainly help you make a decision on the purchase.
If you already are a holder of Pelco CCC5100H, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Pelco CCC5100H.
However, one of the most important roles played by the user manual is to help in solving problems with Pelco CCC5100H. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Pelco CCC5100H along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
